Hello there,
I have connected the debug cable, heres the output:
/U-Boot SPL 2014.10-rc2-00017-g621bc23 (Sep 04 2014 - 19:58:48)//
//
//
//U-Boot 2014.10-rc2-00017-g621bc23 (Sep 04 2014 - 19:58:48), Build:
jenkins-github_Bootloader-Builder-22//
//
// Watchdog enabled//
//I2C: ready//
//DRAM: 512 MiB//
//MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1//
//Using default environment//
//
//Net: <ethaddr> not set. Validating first E-fuse MAC//
//cpsw, usb_ether//
//Hit any key to stop autoboot: 0//
//gpio: pin 53 (gpio 53) value is 1//
//Card did not respond to voltage select!//
//Card did not respond to voltage select!//
//gpio: pin 56 (gpio 56) value is 0//
//gpio: pin 55 (gpio 55) value is 0//
//gpio: pin 54 (gpio 54) value is 0//
//switch to partitions #0, OK//
//mmc1(part 0) is current device//
//gpio: pin 54 (gpio 54) value is 1//
//SD/MMC found on device 1//
//Checking for: /uEnv.txt ...//
//Checking for: /boot.scr ...//
//Checking for: /boot/boot.scr ...//
//Checking for: /boot/uEnv.txt ...//
//gpio: pin 55 (gpio 55) value is 1//
//764 bytes read in 21 ms (35.2 KiB/s)//
//Loaded environment from /boot/uEnv.txt//
//Checking if uname_r is set in /boot/uEnv.txt...//
//gpio: pin 56 (gpio 56) value is 1//
//Running uname_boot ...//
//loading /boot/vmlinuz-3.8.13-bone64 ...//
//5605264 bytes read in 377 ms (14.2 MiB/s)//
//loading /boot/dtbs/3.8.13-bone64/am335x-boneblack.dtb ...//
//26098 bytes read in 30 ms (848.6 KiB/s)//
//loading /boot/initrd.img-3.8.13-bone64 ...//
//2282569 bytes read in 150 ms (14.5 MiB/s)//
//debug: [console=ttyO0,115200n8
root=UUID=49a3b628-4d8e-4a0f-b159-bd265e36a9df ro rootfstype=ext4
rootwait fixrtc quiet init=/lib/systemd/systemd] ...//
//debug: [bootz 0x82000000 0x88080000:22d449 0x88000000] ...//
//Kernel image @ 0x82000000 [ 0x000000 - 0x558790 ]//
//## Flattened Device Tree blob at 88000000//
// Booting using the fdt blob at 0x88000000//
// Loading Ramdisk to 8fdd2000, end 8ffff449 ... OK//
// Loading Device Tree to 8fdc8000, end 8fdd15f1 ... OK//
//
//Starting kernel ...//
//
//Uncompressing Linux... done, booting the kernel.//
//[ 0.338513] omap2_mbox_probe: platform not supported//
//[ 0.493476] tps65217-bl tps65217-bl: no platform data provided//
//[ 0.553819] bone-capemgr bone_capemgr.9: slot #0: No cape found//
//[ 0.590929] bone-capemgr bone_capemgr.9: slot #1: No cape found//
//[ 0.628036] bone-capemgr bone_capemgr.9: slot #2: No cape found//
//[ 0.665145] bone-capemgr bone_capemgr.9: slot #3: No cape found//
//[ 0.680842] bone-capemgr bone_capemgr.9: slot #6: BB-BONELT-HDMIN
conflict P8.45 (#5:BB-BONELT-HDMI)//
//[ 0.690402] bone-capemgr bone_capemgr.9: slot #6: Failed verification//
//[ 0.697136] bone-capemgr bone_capemgr.9: loader: failed to load
slot-6 BB-BONELT-HDMIN:00A0 (prio 2)//
//[ 0.713682] omap_hsmmc mmc.5: of_parse_phandle_with_args of 'reset'
failed//
//[ 0.776740] pinctrl-single 44e10800.pinmux: pin 44e10854 already
requested by 44e10800.pinmux; cannot claim for gpio-leds.8//
//[ 0.788424] pinctrl-single 44e10800.pinmux: pin-21 (gpio-leds.8)
status -22//
//[ 0.795694] pinctrl-single 44e10800.pinmux: could not request pin
21 on device pinctrl-single//
//Loading, please wait...//
//systemd-fsck[201]: rootfs: clean, 12849/111104 files, 77267/444160
blocks//
//Welcome to emergency mode. Use "systemctl default" or ^D to enter
default mode./
Then I enter systemctl default to enter the prompt. I comment the fstab
entry adn everything works again. I tried to read into your script, I
found the place where the partition is created:
/if [ "x${bborg_production}" = "xenable" ] ; then//
// conf_boot_endmb="96"//
// conf_boot_fstype="fat"//
// sfdisk_fstype="0xE"//
// sfdisk_partition_layout//
// else//
// sfdisk_single_partition_layout//
// media_rootfs_partition=1//
// fi/
You said that everything is stored on a single partition in this image,
while it looks like there is a second one in fat16 for the usb. Im not
sure either I understand this correctly, if this is a single partition,
how can i create a separate one for the usb? I would really aprichiate
your help.
W dniu 2014-09-30 15:38, Robert Nelson pisze:
On Tue, Sep 30, 2014 at 8:35 AM, Bremenpl <breme...@gmail.com> wrote:
But why can I mount it by hand then without any problems?
I doubt it's really mounting what you think it's mounting..
Regards,
--
Bremenpl
--
For more options, visit http://beagleboard.org/discuss
---
You received this message because you are subscribed to the Google Groups "BeagleBoard" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to beagleboard+unsubscr...@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
