Hi, I have tried to save my information with this procedure, but when the BBB start (Power led ON), with the S2 pushed, The USR leds are not Blinked (OFF), I pushed for several seconds and minutes, but they do not turn ON, after 15 or 20 min. nothing happen inseide the uSD, no data are save?
Could someone help me?, can't have my data save in order to reflashed the BBB El jueves, 26 de septiembre de 2013, 12:16:54 (UTC-5), Jason Kridner escribió: > > There are lots of ways to extract the contents of the eMMC to save off and > reuse. I'm proposing a method using Buildroot and an initramfs such that > you can simply drop a few files from a .zip onto a normal, FAT-formatted SD > card to perform the extraction. There are several things really handy here, > such as the ability to edit autorun.sh to be whatever script you want to > run on your board at boot. In the archive, I only have the necessary > autorun.sh for *saving* your eMMC content. The flip-side is provided here > in the text such that you need to go through a couple of steps before you > trash your eMMC. > > The steps for saving off your eMMC contents to a file: > * Get a 4GB or larger uSD card that is FAT formatted. > * Download https://s3.amazonaws.com/beagle/beagleboneblack-save-emmc.zip > and extract the contents onto your uSD card. > * Eject uSD card from your computer, insert into powered-off BeagleBone > Black and apply power to your board. > * You'll notice USR0 (the LED closest to the S1 button in the corner) will > (after about 20 seconds) start to blink steadily, rather than the > double-pulse "heartbeat" pattern that is typical when your BeagleBone Black > is running the typical Linux kernel configuration. > * It'll run for a bit under 10 minutes and then USR0 will stay ON steady. > That's your cue to remove power, remove the uSD card and put it back into > your computer. > * You should see a file called BeagleBoneBlack-eMMC-image-XXXXX.img, where > XXXXX is a set of random numbers. Save off this file to use for restoring > your image later. > > Because the date won't be set on your board, you might want to adjust the > date on the file to remember when you made it. Delete the file if you want > to make room for a new backup image. For storage on your computer, these > images will typically compress very well, so use your favorite compression > tool. > > To restore the file, make sure there is a valid > BeagleBoneBlack-eMMC-image-XXXX.img file on the uSD card and edit > autorun.sh with your favorite text editor to contain the following: > #!/bin/sh > echo timer > /sys/class/leds/beaglebone\:green\:usr0/trigger > dd if=/mnt/BeagleBoneBlack-eMMC-image-XXXXX.img of=/dev/mmcblk1 bs=10M > sync > echo default-on > /sys/class/leds/beaglebone\:green\:usr0/trigger > > *NOTE*: Be certain to replace the 'XXXXX' above with the proper name of > your image file. > > This image was built using Buildroot. The sources are at > https://github.com/jadonk/buildroot with tag save-emmc-0.0.1. Download > via https://github.com/jadonk/buildroot/releases/tag/save-emmc-0.0.1 or > clone the git repo. It is a small fork from git:// > git.buildroot.net/buildroot tag e9f6011617528646768e69203e85fe64364b7efd. > > To build, 'make beagleboneblack_defconfig; make; ./mkuimage.sh'. Output > files (am335x-boneblack.dtb, MLO, u-boot.img and uImage) will be in the > output/images subdirectory. The following files were created manually. > > uEnv.txt: > bootpart=0:1 > bootdir= > fdtaddr=0x81FF0000 > optargs=quiet capemgr.disable_partno=BB-BONELT-HDMI,BB-BONELT-HDMIN > uenvcmd=load mmc 0 ${loadaddr} uImage;run loadfdt;setenv bootargs > console=${console} ${optargs};bootm ${loadaddr} - ${fdtaddr} > > autorun.sh: > #!/bin/sh > echo timer > /sys/class/leds/beaglebone\:green\:usr0/trigger > dd if=/dev/mmcblk1 of=/mnt/BeagleBoneBlack-eMMC-image-$RANDOM.img bs=10M > sync > echo default-on > /sys/class/leds/beaglebone\:green\:usr0/trigger > > The kernel is based on > https://github.com/beagleboard/kernel/commit/9fdb452245a58158a4bea787cdc663c17681bcfe, > > but I applied the patches, added firmware and uploaded it to > https://github.com/beagleboard/linux/commit/ddd36e546e53d3c493075bbebd6188ee843208f9 > > to pull down in the Buildroot makefile. The link to the source for the > firmware is in the commit. > > I've applied to join the Buildroot mailing list to send these patches > upstream. The power management firmware is not yet loading properly, but > that is something I can look into. > > Happy hacking! > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to beagleboard+unsubscr...@googlegroups.com. For more options, visit https://groups.google.com/d/optout.
