On Thu, Jan 3, 2019 at 1:56 PM <sam.abb...@gmail.com> wrote:
>
> Hi Robert,
>
> Here below is my boot log:
> """
> U-Boot 2018.09-00002-gd5b4c4b656 (Oct 19 2018 - 14:16:02 -0500), Build: 
> jenkins-
> github_Bootloader-Builder-84
>
> CPU  : AM335X-GP rev 2.1
> I2C:   ready
> DRAM:  512 MiB
> No match for driver 'omap_hsmmc'
> No match for driver 'omap_hsmmc'
> Some drivers were not found
> Reset Source: Global warm SW reset has occurred.
> Reset Source: Power-on reset has occurred.
> RTC 32KCLK Source: External.
> MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
> Loading Environment from EXT4... ** File not found /boot/uboot.env **
>
> ** Unable to read "/boot/uboot.env" from mmc0:1 **
> Board: BeagleBone Black
> <ethaddr> not set. Validating first E-fuse MAC
> BeagleBone Black:
> Timed out in wait_for_event: status=0000
> Check if pads/pull-ups of bus are properly configured
> BeagleBone: cape eeprom: i2c_probe: 0x54:
> Timed out in wait_for_event: status=0000
> Check if pads/pull-ups of bus are properly configured
> BeagleBone: cape eeprom: i2c_probe: 0x55:
> Timed out in wait_for_event: status=0000
> Check if pads/pull-ups of bus are properly configured
> BeagleBone: cape eeprom: i2c_probe: 0x56:
> Timed out in wait_for_event: status=0000
> Check if pads/pull-ups of bus are properly configured
> BeagleBone: cape eeprom: i2c_probe: 0x57:
> Net:   eth0: MII MODE
> cpsw, usb_ether
> Press SPACE to abort autoboot in 2 seconds
> board_name=[A335BNLT] ...
> board_rev=[000C] ...
> switch to partitions #0, OK
> mmc0 is current device
> SD/MMC found on device 0
> switch to partitions #0, OK
> mmc0 is current device
> Scanning mmc 0:1...
> gpio: pin 56 (gpio 56) value is 0
> gpio: pin 55 (gpio 55) value is 0
> gpio: pin 54 (gpio 54) value is 0
> gpio: pin 53 (gpio 53) value is 1
> switch to partitions #0, OK
> mmc0 is current device
> gpio: pin 54 (gpio 54) value is 1
> Checking for: /uEnv.txt ...
> Checking for: /boot.scr ...
> Checking for: /boot/boot.scr ...
> Checking for: /boot/uEnv.txt ...
> gpio: pin 55 (gpio 55) value is 1
> 2100 bytes read in 20 ms (102.5 KiB/s)
> Loaded environment from /boot/uEnv.txt
> debug: [dtb=am335x-boneblack.dtb] ...
> Using: dtb=am335x-boneblack.dtb ...
> Checking if uname_r is set in /boot/uEnv.txt...
> gpio: pin 56 (gpio 56) value is 1
> Running uname_boot ...
> loading /boot/vmlinuz-4.9.45-ti-r57 ...
> 9464664 bytes read in 612 ms (14.7 MiB/s)
> debug: [enable_uboot_overlays=1] ...
> debug: [enable_uboot_cape_universal=1] ...
> debug: [uboot_base_dtb_univ=am335x-boneblack-uboot-univ.dtb] ...
> uboot_overlays: [uboot_base_dtb=am335x-boneblack-uboot-univ.dtb] ...
> debug: unable to find [am335x-boneblack-uboot-univ.dtb] using 
> [am335x-boneblack-
> uboot.dtb] instead ...
> debug: [uboot_base_dtb_univ=am335x-boneblack-uboot.dtb] ...
> uboot_overlays: [uboot_base_dtb=am335x-boneblack-uboot.dtb] ...
> uboot_overlays: Switching too: dtb=am335x-boneblack-uboot.dtb ...
> loading /boot/dtbs/4.9.45-ti-r57/am335x-boneblack-uboot.dtb ...
> 55752 bytes read in 36 ms (1.5 MiB/s)
> uboot_overlays: [fdt_buffer=0x60000] ...
> uboot_overlays: loading /lib/firmware/BB-BONE-eMMC1-01-00A0.dtbo ...
> 1440 bytes read in 345 ms (3.9 KiB/s)
> uboot_overlays: loading /lib/firmware/BB-HDMI-TDA998x-00A0.dtbo ...
> 4920 bytes read in 219 ms (21.5 KiB/s)
> uboot_overlays: loading /lib/firmware/BB-ADC-00A0.dtbo ...
> 711 bytes read in 599 ms (1000 Bytes/s)
> uboot_overlays: loading /lib/firmware/univ-bbb-EVA-00A0.dtbo ...
> 61976 bytes read in 644 ms (93.8 KiB/s)
> loading /boot/initrd.img-4.9.45-ti-r57 ...
> 6395122 bytes read in 420 ms (14.5 MiB/s)
> debug: [console=ttyO0,115200n8 bone_capemgr.uboot_capemgr_enabled=1 
> root=/dev/mm
> cblk0p1 ro rootfstype=ext4 rootwait coherent_pool=1M net.ifnames=0 quiet 
> video=H
> DMI-A-1:1024x768@60e] ...
> debug: [bootz 0x82000000 0x88080000:6194f2 88000000] ...
> ## Flattened Device Tree blob at 88000000
>    Booting using the fdt blob at 0x88000000
>    Loading Ramdisk to 8f9e6000, end 8ffff4f2 ... OK
>    reserving fdt memory region: addr=88000000 size=7d000
>    Loading Device Tree to 8f966000, end 8f9e5fff ... OK
>
> Starting kernel ...
>
> [    0.001790] clocksource_probe: no matching clocksources found
> [    2.416644] wkup_m3_ipc 44e11324.wkup_m3_ipc: could not get rproc handle
> [    2.670204] omap_voltage_late_init: Voltage driver support not added
> [    2.677613] PM: Cannot get wkup_m3_ipc handle
> [    3.167898] musb-hdrc musb-hdrc.1: VBUS_ERROR in a_wait_vrise (80, 
> <SessEnd),
>  retry #3, port1 0008010c
> [    4.089472] tda998x 0-0070: read edid timeout
> [    4.185191] bone_capemgr bone_capemgr: slot #0: auto loading handled by 
> U-Boo
> t
> [    4.192591] bone_capemgr bone_capemgr: slot #1: auto loading handled by 
> U-Boo
> t
> [    4.200032] bone_capemgr bone_capemgr: slot #2: auto loading handled by 
> U-Boo
> t
> [    4.207386] bone_capemgr bone_capemgr: slot #3: auto loading handled by 
> U-Boo
> t
> [    6.389654] tda998x 0-0070: read edid timeout
> rootfs: clean, 127622/217728 files, 744131/869376 blocks
>
> Debian GNU/Linux 9 beaglebone ttyS0
>
> BeagleBoard.org Debian Image 2017-08-31
>
> Support/FAQ: http://elinux.org/Beagleboard:BeagleBoneBlack_Debian
>
> default username:password is [debian:temppwd]
>
> beaglebone login: debian
> Password:
>
> """"
> For the same image, please also see my boot log on beaglebone.
>
> U-Boot 2016.03-00001-gd12d09f (Mar 17 2016 - 16:16:15 -0500), Build: 
> jenkins-gi1
>
>        Watchdog enabled
> I2C:   ready
> DRAM:  512 MiB
> Reset Source: Power-on reset has occurred.
> MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
> Using default environment
>
> Net:   <ethaddr> not set. Validating first E-fuse MAC
> cpsw, usb_ether
> Press SPACE to abort autoboot in 2 seconds
> switch to partitions #0, OK
> mmc0 is current device
> Scanning mmc 0:1...
> gpio: pin 56 (gpio 56) value is 0
> gpio: pin 55 (gpio 55) value is 0
> gpio: pin 54 (gpio 54) value is 0
> gpio: pin 53 (gpio 53) value is 1
> switch to partitions #0, OK
> mmc0 is current device
> gpio: pin 54 (gpio 54) value is 1
> Checking for: /uEnv.txt ...
> Checking for: /boot.scr ...
> Checking for: /boot/boot.scr ...
> Checking for: /boot/uEnv.txt ...
> gpio: pin 55 (gpio 55) value is 1
> 2080 bytes read in 40 ms (50.8 KiB/s)
> Loaded environment from /boot/uEnv.txt
> Checking if uname_r is set in /boot/uEnv.txt...
> gpio: pin 56 (gpio 56) value is 1
> Running uname_boot ...
> loading /boot/vmlinuz-4.9.45-ti-r57 ...
> 9464664 bytes read in 546 ms (16.5 MiB/s)
> loading /boot/dtbs/4.9.45-ti-r57/am335x-boneblack.dtb ...
> 58161 bytes read in 95 ms (597.7 KiB/s)
> loading /boot/initrd.img-4.9.45-ti-r57 ...
> 6395122 bytes read in 384 ms (15.9 MiB/s)
> debug: [console=ttyO0,115200n8 root=/dev/mmcblk0p1 ro rootfstype=ext4 
> rootwait .
> debug: [bootz 0x82000000 0x88080000:6194f2 0x88000000] ...
> Kernel image @ 0x82000000 [ 0x000000 - 0x906b58 ]
> ## Flattened Device Tree blob at 88000000
>    Booting using the fdt blob at 0x88000000
>    Loading Ramdisk to 8f9e6000, end 8ffff4f2 ... OK
>    Loading Device Tree to 8f9d4000, end 8f9e5330 ... OK
>
> Starting kernel ...
>
> [    0.000861] clocksource_probe: no matching clocksources found
> [    2.352397] wkup_m3_ipc 44e11324.wkup_m3_ipc: could not get rproc handle
> [    2.570055] omap_voltage_late_init: Voltage driver support not added
> [    2.577597] PM: Cannot get wkup_m3_ipc handle
> [    2.944617] bone_capemgr bone_capemgr: slot #0: No cape found
> [    2.975621] bone_capemgr bone_capemgr: slot #1: No cape found
> [    3.008278] bone_capemgr bone_capemgr: slot #2: No cape found
> [    3.040942] bone_capemgr bone_capemgr: slot #3: No cape found
> rootfs: recovering journal
> rootfs: Clearing orphaned inode 72631 (uid=0, gid=0, mode=040700, size=4096)
> rootfs: Clearing orphaned inode 72632 (uid=0, gid=0, mode=041777, size=4096)
> rootfs: clean, 126996/217728 files, 740103/869376 blocks
> [   18.675503] tilcdc 4830e000.lcdc: tilcdc_crtc_irq(0x00000020): FIFO 
> underflow
> [   18.683167] tilcdc 4830e000.lcdc: tilcdc_crtc_irq(0x00000004): Sync lost
> [   18.690576] tilcdc 4830e000.lcdc: tilcdc_crtc_irq(0x00000004): Sync lost
> [   18.699830] tilcdc 4830e000.lcdc: tilcdc_crtc_irq(0x00000004): Sync lost
> [   18.700543] tilcdc 4830e000.lcdc: tilcdc_crtc_irq(0x00000004): Sync lost
> [   18.716500] tilcdc 4830e000.lcdc: tilcdc_crtc_irq(0x00000004): Sync lost
> [   18.717208] tilcdc 4830e000.lcdc: tilcdc_crtc_irq(0x00000004): Sync lost
> [   18.733165] tilcdc 4830e000.lcdc: tilcdc_crtc_irq(0x00000004): Sync lost
> [   18.733870] tilcdc 4830e000.lcdc: tilcdc_crtc_irq(0x00000004): Sync lost
> [   18.749842] tilcdc 4830e000.lcdc: tilcdc_crtc_irq(0x00000004): Sync lost
> [   18.750537] tilcdc 4830e000.lcdc: tilcdc_crtc_irq(0x00000004): Sync lost
> [   19.133859] tilcdc 4830e000.lcdc: tilcdc_crtc_irq(0x00000004): Sync lost 
> flog
>
> Debian GNU/Linux 9 beaglebone ttyS0
>
> BeagleBoard.org Debian Image 2017-08-31
>
> Support/FAQ: http://elinux.org/Beagleboard:BeagleBoneBlack_Debian
>
> default username:password is [debian:temppwd]
>
> beaglebone login:
> ********
> The only difference I see in the log is U-boot bootloader being a different 
> version in beaglebone. In beaglebone its not showing when it loads u-boot 
> overlays.
>
> Also during Kernel loading I can see this tilcdc: "[   18.683167] tilcdc 
> 4830e000.lcdc: tilcdc_crtc_irq(0x00000004): Sync lost ", but I don't see this 
> during boot on the clone board.

This ^ was fixed in u-boot back in v2017.01-rc2:

https://github.com/u-boot/u-boot/commit/8c17cbdf8a8023abdd0009af4dc9dbc0541b4a0f#diff-5ceb6e6d8a7e6348a75c69a248999eb3

>
> I would really appreciate if you can help me out with fixing the colors.

Please retest with
https://rcn-ee.net/rootfs/bb.org/testing/2018-12-30/stretch-lxqt/bone-debian-9.6-lxqt-armhf-2018-12-30-4gb.img.xz

Using u-boot v2018.09 and v4.14.x based kernel that is shipped with the image..

Regards,

-- 
Robert Nelson
https://rcn-ee.com/

-- 
For more options, visit http://beagleboard.org/discuss
--- 
You received this message because you are subscribed to the Google Groups 
"BeagleBoard" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to beagleboard+unsubscr...@googlegroups.com.
To view this discussion on the web visit 
https://groups.google.com/d/msgid/beagleboard/CAOCHtYhhA1iW3ngH31mik4L%3Dj0Za87BB8_%2BuJK%3DbvZ6s5vyG-w%40mail.gmail.com.
For more options, visit https://groups.google.com/d/optout.

Reply via email to