I had taken off a tire that some one had used this kind of stuff on and it really makes a nasty slimy mess. I had to take several rags and clean every thing up first and then I decided to put a tube in the tire. In my opinion if you are going to go to the trouble of taking off a tire on a small application like a riding mower you might just as well put in an inertube. Robert
-----Original Message----- From: blindhandyman@yahoogroups.com [mailto:[EMAIL PROTECTED] Behalf Of carl Sent: Saturday, April 05, 2008 6:20 AM To: blindhandyman@yahoogroups.com Subject: Re: [BlindHandyMan] Flat tire on riding mower. on a simalor subjeckt i hav heard of a produckt that eather you put on a punckture or you put in your tyres but if you get a punckture it seels it an re inflates the tyre is this trew? ----- Original Message ----- From: Max Robinson To: blindhandyman@yahoogroups.com <mailto:blindhandyman%40yahoogroups.com> Sent: Saturday, April 05, 2008 3:28 AM Subject: Re: [BlindHandyMan] Flat tire on riding mower. I would never try to air up tires without a tire gauge. I'm a pretty cautious guy. Regards. Max. K 4 O D S. Email: [EMAIL PROTECTED] <mailto:max%40maxsmusicplace.com> Transistor site http://www.funwithtransistors.net <http://www.funwithtransistors.net> Vacuum tube site: http://www.funwithtubes.net <http://www.funwithtubes.net> Music site: http://www.maxsmusicplace.com <http://www.maxsmusicplace.com> To subscribe to the fun with tubes group send an email to, [EMAIL PROTECTED] <mailto:funwithtubes-subscribe%40yahoogroups.com> ----- Original Message ----- From: "Robert j" < [EMAIL PROTECTED] <mailto:robertjmoore%40embarqmail.com> > To: < blindhandyman@yahoogroups.com <mailto:blindhandyman%40yahoogroups.com> > Sent: Friday, April 04, 2008 8:16 PM Subject: RE: [BlindHandyMan] Flat tire on riding mower. I have had my share of these and what I find works great is to take the wheel off of the mower and then with the tire in the upwrite position bounce it off the floor and rotate the tire as you do this. this will tend to snap the beed outward with every bounce so if you turn the tire a few inches every time and do this prossess for a couple of rotations you should be good to go. This has never failed to work for me. Although the way that max did it is very reliable too. If I am not mistaken tire places actually have a band that is designed just for that task. While we are on the topic be very carefull about extreme over inflation. I have heard my share of horrer stories. My local mechanic in town here had a friend of his get killed by a truck tire. I think it was actually the rim that got him. It was a large truck tire and it had a split rim. I don't know if they even make them any more. Don't be afraid of airing up your tires but keep within the normal range for the tire that you are airing up. I myself tend to go over the recommendation but only by about 2 pounds. Which is still wel within the maximum. My tires I think recamend about 35 LBS but the maximum states some where around 5 LBS. -----Original Message----- From: blindhandyman@yahoogroups.com <mailto:blindhandyman%40yahoogroups.com> [mailto: blindhandyman@yahoogroups.com <mailto:blindhandyman%40yahoogroups.com> ]On Behalf Of Max Robinson Sent: Thursday, April 03, 2008 7:36 PM To: Blind Handyman Subject: [BlindHandyMan] Flat tire on riding mower. Hi All. Here's a story that may help someone else who finds themselves in the same position some day. This spring, just a few days ago, when we got the riding lawn mower out of its house we found that one of the tires was flat. It had separated from the rim. I thought that lifting it off the ground would allow it to reengage to the rim so I could inflate it with my air compressor. Sue took the compressor hose to the hardware store to get the necessary adaptor to fit a valve stem. Then I cut a piece of scrap 2 by 4 just long enough to hold the wheel, it was a front one, off the carport when placed under the axel. I used an 8 foot 2 by 4 to leaver up the front end while Sue placed the block under the axel. The tire did not pop back into place. We fiddled with it for a while and then decided that was too dangerous so I removed the wheel. We tried several ways of pushing on it but couldn't get it to seal well enough to take air. Then we both had the same thought at the same time. We tied a length of rope around the circumference of the tire, right in the middle. We put a screwdriver through the knot and began to twist. This compression caused the walls of the tire to be forced outward and they finally made a seal good enough to get a few pounds of pressure in the tire. Then we removed the tourniquet and finished inflating to the recommended 15 pounds. Checking the other three tires revield anywhere from 3 to 5 pounds of pressure. We pumped them all up to 15. Before this year we didn't own an air compressor so we couldn't have aired up the tires even if we had thought of it. From now on, checking the tire pressure will be a part of spring maintenance for the riding mower. Regards. Max. K 4 O D S. Email: [EMAIL PROTECTED] <mailto:max%40maxsmusicplace.com> <mailto:max%40maxsmusicplace.com> Transistor site http://www.funwithtransistors.net <http://www.funwithtransistors.net> < http://www.funwithtransistors.net <http://www.funwithtransistors.net> > Vacuum tube site: http://www.funwithtubes.net <http://www.funwithtubes.net> < http://www.funwithtubes.net <http://www.funwithtubes.net> > Music site: http://www.maxsmusicplace.com <http://www.maxsmusicplace.com> < http://www.maxsmusicplace.com <http://www.maxsmusicplace.com> > To subscribe to the fun with tubes group send an email to, [EMAIL PROTECTED] <mailto:funwithtubes-subscribe%40yahoogroups.com> <mailto:funwithtubes-subscribe%40yahoogroups.com> [Non-text portions of this message have been removed] ------------------------------------ To listen to the show archives go to link http://www.acbradio.org/pweb/index.php?module=pagemaster&PAGE_user_op=view_p age&PAGE_id=33&MMN_position=47:29 <http://www.acbradio.org/pweb/index.php?module=pagemaster&PAGE_user_op=view_ page&PAGE_id=33&MMN_position=47:29> Or ftp://ftp.acbradio.org/acbradio-archives/handyman/ <ftp://ftp.acbradio.org/acbradio-archives/handyman/> The Pod Cast address for the Blind Handy Man Show is. http://www.acbradio.org/news/xml/podcast.php?pgm=saturday <http://www.acbradio.org/news/xml/podcast.php?pgm=saturday> Visit The Blind Handy Man Files Page To Review Contributions From Various List Members At The Following address: http://www.jaws-users.com/JAWS/handyman/ <http://www.jaws-users.com/JAWS/handyman/> Visit the archives page at the following address http://www.mail-archive.com/blindhandyman@yahoogroups.com/ <http://www.mail-archive.com/blindhandyman@yahoogroups.com/> If you would like to join the JAWS Users List, then visit the following address for more information: http://www.jaws-users.com/ <http://www.jaws-users.com/> For a complete list of email commands pertaining to the Blind Handy Man list just send a blank message to: [EMAIL PROTECTED] <mailto:blindhandyman-help%40yahoogroups.comYahoo> ! Groups Links -- No virus found in this incoming message. Checked by AVG. Version: 7.5.519 / Virus Database: 269.22.6/1360 - Release Date: 4/4/2008 6:02 PM [Non-text portions of this message have been removed] [Non-text portions of this message have been removed]
