Hello,
So then it seems I may be needing to switch
operating systems. I am currently using XUBUNTU 11.04. Guessing this is
probably my problem. Any recommendations? I'm thinking CentOS...
- Louis Dartez
(956) 372-5812
Arecibo Remote Command Center Scholar
Center for Gravitational Wave Astronomy
University of Texas at Brownsville
On 7/13/11 5:32 PM, Jack Hickish wrote:
Hi Louis,
The error you describe sounds similar to that encountered when trying
to compile on Ubuntu -- see here:
http://www.mail-archive.com/casper@lists.berkeley.edu/msg01224.html
Are you using Centos/RHEL/one of the supported OSs?
Cheers,
Jack
On 13 July 2011 23:10, Louis Dartez <louisdar...@gmail.com
<mailto:louisdar...@gmail.com>> wrote:
Hi Mark,
I tried running ctrl-D and updating my design and
then re-compiling with 'bee_xps' (version 1.1). The compilation
process crashed once more with the exact same message in the
dialogue box as before. The output within the MATLAB command
window is as follows:
Detected Linux OS
#############################
## System Update ##
#############################
Warning: The model 'tutorial1_revisited' does not have continuous
states,
hence Simulink is using the solver 'VariableStepDiscrete' instead of
solver 'ode45'. You can disable this diagnostic by explicitly
specifying
a discrete solver in the solver tab of the Configuration Parameters
dialog, or by setting the 'Automatic solver parameter selection'
diagnostic to 'none' in the Diagnostics tab of the Configuration
Parameters dialog.
> In gen_xps_files at 199
In bee_xps>run_Callback at 150
In bee_xps at 82
Warning: Using a default value of 0.2 for maximum step size. The
simulation step size will be equal to or less than this value.
You can
disable this diagnostic by setting 'Automatic solver parameter
selection'
diagnostic to 'none' in the Diagnostics page of the configuration
parameters dialog.
> In gen_xps_files at 199
In bee_xps>run_Callback at 150
In bee_xps at 82
#############################
## Block objects creation ##
#############################
######################
## Checking objects ##
######################
Running system generator ...
Warning: The model 'tutorial1_revisited' does not have continuous
states,
hence Simulink is using the solver 'VariableStepDiscrete' instead of
solver 'ode45'. You can disable this diagnostic by explicitly
specifying
a discrete solver in the solver tab of the Configuration Parameters
dialog, or by setting the 'Automatic solver parameter selection'
diagnostic to 'none' in the Diagnostics tab of the Configuration
Parameters dialog.
> In
/opt/Xilinx/11.1/DSP_Tools/lin64/sysgen/bin/xlCompileGenerateMdl.p>xlCompileGenerateMdl
at 181
In
/opt/Xilinx/11.1/DSP_Tools/lin64/sysgen/bin/xlGenerateButton.p>xlGenerateButton
at 281
In gen_xps_files at 324
In bee_xps>run_Callback at 150
In bee_xps at 82
Warning: Using a default value of 0.2 for maximum step size. The
simulation step size will be equal to or less than this value.
You can
disable this diagnostic by setting 'Automatic solver parameter
selection' diagnostic to 'none' in the Diagnostics page of the
configuration parameters dialog.
> In
/opt/Xilinx/11.1/DSP_Tools/lin64/sysgen/bin/xlCompileGenerateMdl.p>xlCompileGenerateMdl
at 181
In
/opt/Xilinx/11.1/DSP_Tools/lin64/sysgen/bin/xlGenerateButton.p>xlGenerateButton
at 281
In gen_xps_files at 324
In bee_xps>run_Callback at 150
In bee_xps at 82
>>
I'm at a complete loss as to what may be causing this problem. If
you (or anyone else reading this) know of any other
troubleshooting procedures that may help pin down the problem it
would be greatly appreciated.
Thanks,
Louis
On Mon, Jul 11, 2011 at 2:01 PM, Mark Wagner
<mwag...@ssl.berkeley.edu <mailto:mwag...@ssl.berkeley.edu>> wrote:
Hi Louis,
Can you run control-D to update the design? This
will propagate the data types
and may give you some idea where the issue lies.
Mark
On Fri, Jul 8, 2011 at 9:27 PM, Louis Dartez
<louisdar...@gmail.com <mailto:louisdar...@gmail.com>> wrote:
Hello,
I've been trying to compile tutorial 1 using
the bee_xps command on MATLAB. After waiting a while I get
a dialogue box titled 'NGC Netlisting Error' with the
following errors:
[: 21:
/opt/Xilinx/11.1/ISE/lib/lin64:/opt/Xilinx/11.1/DSP_Tools/lin64/sysgen/lib:
/usr/local/MATLAB/R2009a/sys/os/glnxa64:/usr/local/MATLAB/R2009a/bin/glnxa64:/usr/local/MATLAB/R2009a/extern/lib/glnxa64:/usr/local/MATLAB/R2009a/sys/java/jre/glnxa64/jre/lib/amd64/native_threads:/usr/local/MATLAB/R2009a/sys/java/jre/glnxa64/jre/lib/amd64:/opt/Xilinx/11.1/ISE/bin/lin64:
unexpected operator
[: 22:
/opt/Xilinx/11.1/DSP_Tools/lin64/sysgen/lib:/opt/Xilinx/11.1/ISE/lib/lin64:
/opt/Xilinx/11.1/DSP_Tools/lin64/sysgen/lib:/usr/local/MATLAB/R2009a/sys/os/glnxa64:/usr/local/MATLAB/R2009a/bin/glnxa64:/usr/local/MATLAB/R2009a/extern/lib/glnxa64:/usr/local/MATLAB/R2009a/sys/java/jre/glnxa64/jre/lib/amd64/native_threads:/usr/local/MATLAB/R2009a/sys/java/jre/glnxa64/jre/lib/amd64/server:/usr/local/MATLAB/R2009a/sys/java/jre/glnxa64/jre/lib/amd64:/opt/Xilinx/11.1/ISE/bin/lin64:
unexpected operator
In addition to the dialogue box above, I'm getting the
following output within the MATLAB prompt:
> In
/opt/Xilinx/11.1/DSP_Tools/lin64/sysgen/bin/xlCompileGenerateMdl.p>xlCompileGenerateMdl
at 181
In
/opt/Xilinx/11.1/DSP_Tools/lin64/sysgen/bin/xlGenerateButton.p>xlGenerateButton
at 281
In gen_xps_files at 324
In bee_xps>run_Callback at 150
In bee_xps at 82
Error using ==> gen_xps_files at 328
XSG generation failed:
Any Ideas as to what may be behind these errors? Any
advice would be appreciated.
Thanks,
--
-- Louis Dartez
(956) 372-5812
Arecibo Remote Command Center Scholar
Center for Gravitational Wave Astronomy
University of Texas at Brownsville
--
-- Louis Dartez
(956) 372-5812 <tel:%28956%29%20372-5812>
Arecibo Remote Command Center Scholar
Center for Gravitational Wave Astronomy
University of Texas at Brownsville
