Hi ALL!!!
I have one ROACH-2 boards (ver.2) telling somethings about i2c
read/write failures at boot time (log attached). I have checked all
internal cables and wires and it seems to be all ok, all fans are
rotating at nominal speed (they sound like other ROACHs). Does anybody
have got the same message? I still working on the overall
infrastructure and I didn't test any bof yet. Are these messages
telling there is something so dangerous to deny the use of that board?
The ROACH2 board is booting via NFS and I got no errors when flashing the envs.
Thanks to ALL!
Cheers,
Andrea
################################################################
U-Boot 2011.06-rc2-00000-g2694c9d-dirty (Dec 04 2013 - 20:58:06)
CPU: AMCC PowerPC 440EPx Rev. A at 533.333 MHz (PLB=133 OPB=66 EBC=66)
No Security/Kasumi support
Bootstrap Option C - Boot ROM Location EBC (16 bits)
32 kB I-Cache 32 kB D-Cache
Board: ROACH2
I2C: ready
DRAM: 512 MiB
Flash: 128 MiB
In: serial
Out: serial
Err: serial
CPLD: 2.1
USB: Host(int phy)
I2C read: failed 2
cannot read from i2c device: 54
I2C write: failed 6
DTT: 1 FAILED INIT
I2C write: failed 6
DTT: 2 FAILED INIT
Net: ppc_4xx_eth0
Sensors ConfigI2C write: failed 6
cannot write to i2c device: 50@42
max16071: vmon config failed
I2C write: failed 6
cannot write to i2c device: 51@42
max16071: cmon config failed
I2C write: failed 6
cannot write to i2c device: 4c@01
ad7414: ambient0 config failed
I2C write: failed 6
cannot write to i2c device: 4e@01
ad7414: ambient1 config failed
I2C write: failed 6
cannot write to i2c device: 18@12
max1805: remote temp config failed
I2C write: failed 6
cannot write to i2c device: 48@00
max6650: fpga fan config failed
I2C write: failed 6
cannot write to i2c device: 4b@00
max6650: chs0 config failed
I2C write: failed 6
cannot write to i2c device: 1b@00
max6650: chs1 config failed
I2C write: failed 6
cannot write to i2c device: 1f@00
max6650: chs2 config failed
type run netboot to boot via dhcp+tftp+nfs
type run soloboot to run from flash independent of network
Hit any key to stop autoboot: 0
=> run netboot
Waiting for PHY auto negotiation to complete.. done
ENET Speed is 100 Mbps - FULL duplex connection (EMAC0)
BOOTP broadcast 1
*** Unhandled DHCP Option in OFFER/ACK: 28
*** Unhandled DHCP Option in OFFER/ACK: 28
DHCP client bound to address 192.168.10.122
Using ppc_4xx_eth0 device
TFTP from server 192.168.10.4; our IP address is 192.168.10.122
Filename '/roach2/boot/uImage-r2borph3'.
Load address: 0x4000000
Loading: #################################################################
#################################################################
#######################
done
Bytes transferred = 2231549 (220cfd hex)
## Booting kernel from Legacy Image at 04000000 ...
Image Name: Linux-3.7.0-rc2+
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 2231485 Bytes = 2.1 MiB
Load Address: 00500000
Entry Point: 005010d4
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
CPU clock-frequency <- 0x1fca0550 (533MHz)
CPU timebase-frequency <- 0x1fca0550 (533MHz)
/plb: clock-frequency <- 7f28154 (133MHz)
/plb/opb: clock-frequency <- 3f940aa (67MHz)
/plb/opb/ebc: clock-frequency <- 3f940aa (67MHz)
/plb/opb/serial@ef600300: clock-frequency <- 54c563 (6MHz)
/plb/opb/serial@ef600400: clock-frequency <- 54c563 (6MHz)
Memory <- <0x0 0x0 0x3ffff000> (1023MB)
ethernet0: local-mac-address <- 02:44:01:02:09:4d
zImage starting: loaded at 0x00500000 (sp: 0x1fe22b40)
Allocating 0x4b0508 bytes for kernel ...
gunzipping (0x00000000 <- 0x0050e000:0x00966034)...done 0x447880 bytes
Linux/PowerPC load: console=ttyS0,115200 root=/dev/nfs
rootpath=192.168.10.4:/roach2/current,nolock ip=dhcp
Finalizing device tree... flat tree at 0x973160
roach2: claiming matching platform
Using PowerPC 44x Platform machine description
Linux version 3.7.0-rc2+ (shanly@shanly-HP8710w) (gcc version 4.6.1
20110627 (prerelease) (GCC) ) #21 Mon Nov 19 09:30:32 SAST 2012
bootconsole [udbg0] enabled
setup_arch: bootmem
arch: exit
Zone ranges:
DMA [mem 0x00000000-0x2fffffff]
Normal empty
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x00000000-0x2fffffff]
MMU: Allocated 1088 bytes of context maps for 255 contexts
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 195072
Kernel command line: console=ttyS0,115200 root=/dev/nfs
rootpath=192.168.10.4:/roach2/current,nolock ip=dhcp
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 774576k/786432k available (4176k kernel code, 11856k reserved,
208k data, 417k bss, 144k init)
Kernel virtual memory layout:
* 0xfffdf000..0xfffff000 : fixmap
* 0xfde00000..0xfe000000 : consistent mem
* 0xfddfe000..0xfde00000 : early ioremap
* 0xf1000000..0xfddfe000 : vmalloc & ioremap
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:512 nr_irqs:512 16
UIC0 (32 IRQ sources) at DCR 0xc0
UIC1 (32 IRQ sources) at DCR 0xd0
UIC2 (32 IRQ sources) at DCR 0xe0
clocksource: timebase mult[1e00000] shift[24] registered
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
regulator-dummy: no parameters
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
SCSI subsystem initialized
Switching to clocksource timebase
NET: Registered protocol family 2
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP: reno registered
UDP hash table entries: 512 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 512 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
jffs2: version 2.2. (NAND) \ufffd© 2001-2006 Red Hat, Inc.
ROMFS MTD (C) 2007 Red Hat, Inc.
msgmni has been set to 1512
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0x1ef600300 (irq = 16) is a 16550A
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
serial8250.0: ttyS1 at MMIO 0x1ef600400 (irq = 17) is a 16550A
roach2_fpga: ROACH2 FPGA Access driver
roach2: major 252Virtex 5 family
roach2_fpga 1d0000000.fpga: ROACH2 FPGA driver
roach2_fpga 1d0000000.fpga: check parameters,addr:0x1d0000000,size:0x4000000
roach2_fpga 1d0000000.fpga: ioremap 1d0000000 to f1080000 with size 4000000
roach2_fpga 1d0000000.fpga: ioremap 1c0100000 to f5100000 with size 200000
roach2_fpga 1d0000000.fpga: char devices successfully registered
brd: module loaded
1f8000000.nor_flash: Found 1 x16 devices at 0x0 in 16-bit bank.
Manufacturer ID 0x000001 Chip ID 0x002801
Amd/Fujitsu Extended Query Table at 0x0040
Amd/Fujitsu Extended Query version 1.3.
number of CFI chips: 1
6 ofpart partitions found on MTD device 1f8000000.nor_flash
Creating 6 MTD partitions on "1f8000000.nor_flash":
0x000000000000-0x000000400000 : "kernel"
0x000000400000-0x000004400000 : "rootfs"
0x000004400000-0x000007400000 : "userfs"
0x000007400000-0x000007f00000 : "v6bitstream"
0x000007f40000-0x000007f80000 : "ubootenv"
0x000007f80000-0x000008000000 : "uboot"
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <m...@qualcomm.com>
PPC 4xx OCP EMAC driver, version 3.54
MAL v2 /plb/mcmal, 2 TX channels, 2 RX channels
ZMII /plb/opb/emac-zmii@ef600d00 initialized
RGMII /plb/opb/emac-rgmii@ef601000 initialized with MDIO support
/plb/opb/emac-rgmii@ef601000: input 0 in RGMII mode
eth0: EMAC-0 /plb/opb/ethernet@ef600e00, MAC 02:44:01:02:09:4d
eth0: found Marvell 88E1111 Ethernet PHY (0x01)
PPP generic driver version 2.4.2
mousedev: PS/2 mouse device common for all mice
input: roach2chassis as /devices/virtual/input/input0
ibm-iic 1ef600700.i2c: using standard (100 kHz) mode
ibm-iic 1ef600800.i2c: using standard (100 kHz) mode
ad7414 0-004c: chip found
ad7414 0-004c: ad7414_probe unable to read config register.
ad7414 0-004e: chip found
ad7414 0-004e: ad7414_probe unable to read config register.
max16065: probe of 0-0050 failed with error -121
max16065: probe of 0-0051 failed with error -121
max6650 0-0048: Error reading config, aborting.
max6650: probe of 0-0048 failed with error -5
max6650 0-004b: Error reading config, aborting.
max6650: probe of 0-004b failed with error -5
max6650 0-001b: Error reading config, aborting.
max6650: probe of 0-001b failed with error -5
max6650 0-001f: Error reading config, aborting.
max6650: probe of 0-001f failed with error -5
cpuidle: using governor ladder
cpuidle: using governor menu
IPv4 over IPv4 tunneling driver
TCP: cubic registered
NET: Registered protocol family 17
Key type dns_resolver registered
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
### of_selftest(): No testcase data in device tree; not running tests
eth0: link is up, 100 FDX, pause enabled
Sending DHCP requests ., OK
IP-Config: Got DHCP answer from 192.168.10.4, my address is 192.168.10.122
IP-Config: Complete:
device=eth0, addr=192.168.10.122, mask=255.255.255.0, gw=255.255.255.255
host=roach-2-b, domain=, nis-domain=(none)
bootserver=192.168.10.4, rootserver=192.168.10.4,
rootpath=/roach2/current,nolock
nameserver0=192.168.10.4VFS: Mounted root (nfs filesystem)
readonly on device 0:11.
Freeing unused kernel memory: 144k freed
INIT: version 2.88 booting
about to run simple init script
warning: can't open /etc/mtab: No such file or directory
mount: mount point /proc/bus/usb does not exist
INIT: Entering runlevel: 2
1 Jan 00:00:10 ntpdate[446]: no servers can be used, exiting
Starting OpenBSD Secure Shell server: sshd.
Starting NFS common utilities: statd failed!
Starting NTP server: ntpd.
tcpborphserver: ... loading roach mmap driver ...
insmod: can't read '/lib/modules/roach_mmap.ko': No such file or directory
version *3* using mmap
tcpborphserver3: about to go into background
Debian GNU/Linux 6.0 roach-2-b ttyS0
roach-2-b login:
--
Andrea Mattana
I.N.A.F. - Istituto di Radioastronomia
Radiotelescopi di Medicina
Via Fiorentina, 3513 - 40059 Medicina (Bo)
Tel. 051/6965834 Fax. 051/6965810
