Yes the same U-boot version and boot procedure. How can test it without looking at the terminal console?
Thanks, Andrea 2014-11-17 13:40 GMT+01:00 John Ford <jf...@nrao.edu>: >> Thanks John, >> but I see this behaviour only on one board out of 4 with the same >> conditions, I guess should be deterministic, doesn't it? > > It seems so to me. Do they all have the same operating system image and > boot setup? > > I can't explain it, but it seems to be the same errors I saw. If you > don't have the usb plugged in, do you still get the errors? > > John > >> >> >> 2014-11-17 13:22 GMT+01:00 John Ford <jf...@nrao.edu>: >>>> Hi ALL!!! >>>> >>>> I have one ROACH-2 boards (ver.2) telling somethings about i2c >>>> read/write failures at boot time (log attached). I have checked all >>>> internal cables and wires and it seems to be all ok, all fans are >>>> rotating at nominal speed (they sound like other ROACHs). Does anybody >>>> have got the same message? I still working on the overall >>>> infrastructure and I didn't test any bof yet. Are these messages >>>> telling there is something so dangerous to deny the use of that board? >>>> >>>> The ROACH2 board is booting via NFS and I got no errors when flashing >>>> the >>>> envs. >>> Hi. >>> >>> I have found that the IIC does not work right if the console port is >>> active, i.e. with the usb cable plugged in. See: >>> >>> http://www.mail-archive.com/casper%40lists.berkeley.edu/msg04861.html >>> >>> John >>> >>>> >>>> Thanks to ALL! >>>> >>>> Cheers, >>>> Andrea >>>> >>>> ################################################################ >>>> >>>> U-Boot 2011.06-rc2-00000-g2694c9d-dirty (Dec 04 2013 - 20:58:06) >>>> >>>> CPU: AMCC PowerPC 440EPx Rev. A at 533.333 MHz (PLB=133 OPB=66 >>>> EBC=66) >>>> No Security/Kasumi support >>>> Bootstrap Option C - Boot ROM Location EBC (16 bits) >>>> 32 kB I-Cache 32 kB D-Cache >>>> Board: ROACH2 >>>> I2C: ready >>>> DRAM: 512 MiB >>>> Flash: 128 MiB >>>> In: serial >>>> Out: serial >>>> Err: serial >>>> CPLD: 2.1 >>>> USB: Host(int phy) >>>> I2C read: failed 2 >>>> cannot read from i2c device: 54 >>>> I2C write: failed 6 >>>> DTT: 1 FAILED INIT >>>> I2C write: failed 6 >>>> DTT: 2 FAILED INIT >>>> Net: ppc_4xx_eth0 >>>> Sensors ConfigI2C write: failed 6 >>>> cannot write to i2c device: 50@42 >>>> max16071: vmon config failed >>>> I2C write: failed 6 >>>> cannot write to i2c device: 51@42 >>>> max16071: cmon config failed >>>> I2C write: failed 6 >>>> cannot write to i2c device: 4c@01 >>>> ad7414: ambient0 config failed >>>> I2C write: failed 6 >>>> cannot write to i2c device: 4e@01 >>>> ad7414: ambient1 config failed >>>> I2C write: failed 6 >>>> cannot write to i2c device: 18@12 >>>> max1805: remote temp config failed >>>> I2C write: failed 6 >>>> cannot write to i2c device: 48@00 >>>> max6650: fpga fan config failed >>>> I2C write: failed 6 >>>> cannot write to i2c device: 4b@00 >>>> max6650: chs0 config failed >>>> I2C write: failed 6 >>>> cannot write to i2c device: 1b@00 >>>> max6650: chs1 config failed >>>> I2C write: failed 6 >>>> cannot write to i2c device: 1f@00 >>>> max6650: chs2 config failed >>>> >>>> type run netboot to boot via dhcp+tftp+nfs >>>> type run soloboot to run from flash independent of network >>>> >>>> Hit any key to stop autoboot: 0 >>>> => run netboot >>>> Waiting for PHY auto negotiation to complete.. done >>>> ENET Speed is 100 Mbps - FULL duplex connection (EMAC0) >>>> BOOTP broadcast 1 >>>> *** Unhandled DHCP Option in OFFER/ACK: 28 >>>> *** Unhandled DHCP Option in OFFER/ACK: 28 >>>> DHCP client bound to address 192.168.10.122 >>>> Using ppc_4xx_eth0 device >>>> TFTP from server 192.168.10.4; our IP address is 192.168.10.122 >>>> Filename '/roach2/boot/uImage-r2borph3'. >>>> Load address: 0x4000000 >>>> Loading: >>>> ################################################################# >>>> ################################################################# >>>> ####################### >>>> done >>>> Bytes transferred = 2231549 (220cfd hex) >>>> ## Booting kernel from Legacy Image at 04000000 ... >>>> Image Name: Linux-3.7.0-rc2+ >>>> Image Type: PowerPC Linux Kernel Image (gzip compressed) >>>> Data Size: 2231485 Bytes = 2.1 MiB >>>> Load Address: 00500000 >>>> Entry Point: 005010d4 >>>> Verifying Checksum ... OK >>>> Uncompressing Kernel Image ... OK >>>> CPU clock-frequency <- 0x1fca0550 (533MHz) >>>> CPU timebase-frequency <- 0x1fca0550 (533MHz) >>>> /plb: clock-frequency <- 7f28154 (133MHz) >>>> /plb/opb: clock-frequency <- 3f940aa (67MHz) >>>> /plb/opb/ebc: clock-frequency <- 3f940aa (67MHz) >>>> /plb/opb/serial@ef600300: clock-frequency <- 54c563 (6MHz) >>>> /plb/opb/serial@ef600400: clock-frequency <- 54c563 (6MHz) >>>> Memory <- <0x0 0x0 0x3ffff000> (1023MB) >>>> ethernet0: local-mac-address <- 02:44:01:02:09:4d >>>> >>>> zImage starting: loaded at 0x00500000 (sp: 0x1fe22b40) >>>> Allocating 0x4b0508 bytes for kernel ... >>>> gunzipping (0x00000000 <- 0x0050e000:0x00966034)...done 0x447880 bytes >>>> >>>> Linux/PowerPC load: console=ttyS0,115200 root=/dev/nfs >>>> rootpath=192.168.10.4:/roach2/current,nolock ip=dhcp >>>> Finalizing device tree... flat tree at 0x973160 >>>> roach2: claiming matching platform >>>> Using PowerPC 44x Platform machine description >>>> Linux version 3.7.0-rc2+ (shanly@shanly-HP8710w) (gcc version 4.6.1 >>>> 20110627 (prerelease) (GCC) ) #21 Mon Nov 19 09:30:32 SAST 2012 >>>> bootconsole [udbg0] enabled >>>> setup_arch: bootmem >>>> arch: exit >>>> Zone ranges: >>>> DMA [mem 0x00000000-0x2fffffff] >>>> Normal empty >>>> Movable zone start for each node >>>> Early memory node ranges >>>> node 0: [mem 0x00000000-0x2fffffff] >>>> MMU: Allocated 1088 bytes of context maps for 255 contexts >>>> Built 1 zonelists in Zone order, mobility grouping on. Total pages: >>>> 195072 >>>> Kernel command line: console=ttyS0,115200 root=/dev/nfs >>>> rootpath=192.168.10.4:/roach2/current,nolock ip=dhcp >>>> PID hash table entries: 4096 (order: 2, 16384 bytes) >>>> Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) >>>> Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) >>>> Memory: 774576k/786432k available (4176k kernel code, 11856k reserved, >>>> 208k data, 417k bss, 144k init) >>>> Kernel virtual memory layout: >>>> * 0xfffdf000..0xfffff000 : fixmap >>>> * 0xfde00000..0xfe000000 : consistent mem >>>> * 0xfddfe000..0xfde00000 : early ioremap >>>> * 0xf1000000..0xfddfe000 : vmalloc & ioremap >>>> SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 >>>> NR_IRQS:512 nr_irqs:512 16 >>>> UIC0 (32 IRQ sources) at DCR 0xc0 >>>> UIC1 (32 IRQ sources) at DCR 0xd0 >>>> UIC2 (32 IRQ sources) at DCR 0xe0 >>>> clocksource: timebase mult[1e00000] shift[24] registered >>>> pid_max: default: 32768 minimum: 301 >>>> Mount-cache hash table entries: 512 >>>> regulator-dummy: no parameters >>>> NET: Registered protocol family 16 >>>> >>>> bio: create slab <bio-0> at 0 >>>> SCSI subsystem initialized >>>> Switching to clocksource timebase >>>> NET: Registered protocol family 2 >>>> TCP established hash table entries: 131072 (order: 8, 1048576 bytes) >>>> TCP bind hash table entries: 65536 (order: 6, 262144 bytes) >>>> TCP: Hash tables configured (established 131072 bind 65536) >>>> TCP: reno registered >>>> UDP hash table entries: 512 (order: 1, 8192 bytes) >>>> UDP-Lite hash table entries: 512 (order: 1, 8192 bytes) >>>> NET: Registered protocol family 1 >>>> RPC: Registered named UNIX socket transport module. >>>> RPC: Registered udp transport module. >>>> RPC: Registered tcp transport module. >>>> RPC: Registered tcp NFSv4.1 backchannel transport module. >>>> squashfs: version 4.0 (2009/01/31) Phillip Lougher >>>> jffs2: version 2.2. (NAND) \ufffd© 2001-2006 Red Hat, Inc. >>>> ROMFS MTD (C) 2007 Red Hat, Inc. >>>> msgmni has been set to 1512 >>>> alg: No test for stdrng (krng) >>>> Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) >>>> io scheduler noop registered >>>> io scheduler deadline registered >>>> io scheduler cfq registered (default) >>>> Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled >>>> serial8250.0: ttyS0 at MMIO 0x1ef600300 (irq = 16) is a 16550A >>>> console [ttyS0] enabled, bootconsole disabled >>>> console [ttyS0] enabled, bootconsole disabled >>>> serial8250.0: ttyS1 at MMIO 0x1ef600400 (irq = 17) is a 16550A >>>> roach2_fpga: ROACH2 FPGA Access driver >>>> roach2: major 252Virtex 5 family >>>> roach2_fpga 1d0000000.fpga: ROACH2 FPGA driver >>>> roach2_fpga 1d0000000.fpga: check >>>> parameters,addr:0x1d0000000,size:0x4000000 >>>> roach2_fpga 1d0000000.fpga: ioremap 1d0000000 to f1080000 with size >>>> 4000000 >>>> roach2_fpga 1d0000000.fpga: ioremap 1c0100000 to f5100000 with size >>>> 200000 >>>> roach2_fpga 1d0000000.fpga: char devices successfully registered >>>> brd: module loaded >>>> 1f8000000.nor_flash: Found 1 x16 devices at 0x0 in 16-bit bank. >>>> Manufacturer ID 0x000001 Chip ID 0x002801 >>>> Amd/Fujitsu Extended Query Table at 0x0040 >>>> Amd/Fujitsu Extended Query version 1.3. >>>> number of CFI chips: 1 >>>> 6 ofpart partitions found on MTD device 1f8000000.nor_flash >>>> Creating 6 MTD partitions on "1f8000000.nor_flash": >>>> 0x000000000000-0x000000400000 : "kernel" >>>> 0x000000400000-0x000004400000 : "rootfs" >>>> 0x000004400000-0x000007400000 : "userfs" >>>> 0x000007400000-0x000007f00000 : "v6bitstream" >>>> 0x000007f40000-0x000007f80000 : "ubootenv" >>>> 0x000007f80000-0x000008000000 : "uboot" >>>> tun: Universal TUN/TAP device driver, 1.6 >>>> tun: (C) 1999-2004 Max Krasnyansky <m...@qualcomm.com> >>>> PPC 4xx OCP EMAC driver, version 3.54 >>>> MAL v2 /plb/mcmal, 2 TX channels, 2 RX channels >>>> ZMII /plb/opb/emac-zmii@ef600d00 initialized >>>> RGMII /plb/opb/emac-rgmii@ef601000 initialized with MDIO support >>>> /plb/opb/emac-rgmii@ef601000: input 0 in RGMII mode >>>> eth0: EMAC-0 /plb/opb/ethernet@ef600e00, MAC 02:44:01:02:09:4d >>>> eth0: found Marvell 88E1111 Ethernet PHY (0x01) >>>> PPP generic driver version 2.4.2 >>>> mousedev: PS/2 mouse device common for all mice >>>> input: roach2chassis as /devices/virtual/input/input0 >>>> ibm-iic 1ef600700.i2c: using standard (100 kHz) mode >>>> ibm-iic 1ef600800.i2c: using standard (100 kHz) mode >>>> ad7414 0-004c: chip found >>>> ad7414 0-004c: ad7414_probe unable to read config register. >>>> ad7414 0-004e: chip found >>>> ad7414 0-004e: ad7414_probe unable to read config register. >>>> max16065: probe of 0-0050 failed with error -121 >>>> max16065: probe of 0-0051 failed with error -121 >>>> max6650 0-0048: Error reading config, aborting. >>>> max6650: probe of 0-0048 failed with error -5 >>>> max6650 0-004b: Error reading config, aborting. >>>> max6650: probe of 0-004b failed with error -5 >>>> max6650 0-001b: Error reading config, aborting. >>>> max6650: probe of 0-001b failed with error -5 >>>> max6650 0-001f: Error reading config, aborting. >>>> max6650: probe of 0-001f failed with error -5 >>>> cpuidle: using governor ladder >>>> cpuidle: using governor menu >>>> IPv4 over IPv4 tunneling driver >>>> TCP: cubic registered >>>> NET: Registered protocol family 17 >>>> Key type dns_resolver registered >>>> drivers/rtc/hctosys.c: unable to open rtc device (rtc0) >>>> ### of_selftest(): No testcase data in device tree; not running tests >>>> eth0: link is up, 100 FDX, pause enabled >>>> Sending DHCP requests ., OK >>>> IP-Config: Got DHCP answer from 192.168.10.4, my address is >>>> 192.168.10.122 >>>> IP-Config: Complete: >>>> device=eth0, addr=192.168.10.122, mask=255.255.255.0, >>>> gw=255.255.255.255 >>>> host=roach-2-b, domain=, nis-domain=(none) >>>> bootserver=192.168.10.4, rootserver=192.168.10.4, >>>> rootpath=/roach2/current,nolock >>>> nameserver0=192.168.10.4VFS: Mounted root (nfs filesystem) >>>> readonly on device 0:11. >>>> Freeing unused kernel memory: 144k freed >>>> INIT: version 2.88 booting >>>> about to run simple init script >>>> warning: can't open /etc/mtab: No such file or directory >>>> mount: mount point /proc/bus/usb does not exist >>>> INIT: Entering runlevel: 2 >>>> 1 Jan 00:00:10 ntpdate[446]: no servers can be used, exiting >>>> Starting OpenBSD Secure Shell server: sshd. >>>> Starting NFS common utilities: statd failed! >>>> Starting NTP server: ntpd. >>>> tcpborphserver: ... loading roach mmap driver ... >>>> insmod: can't read '/lib/modules/roach_mmap.ko': No such file or >>>> directory >>>> version *3* using mmap >>>> tcpborphserver3: about to go into background >>>> >>>> Debian GNU/Linux 6.0 roach-2-b ttyS0 >>>> >>>> roach-2-b login: >>>> >>>> >>>> -- >>>> Andrea Mattana >>>> >>>> I.N.A.F. - Istituto di Radioastronomia >>>> Radiotelescopi di Medicina >>>> Via Fiorentina, 3513 - 40059 Medicina (Bo) >>>> Tel. 051/6965834 Fax. 051/6965810 >>>> >>>> >>> >>> >> >> >> >> -- >> Andrea Mattana >> >> I.N.A.F. - Istituto di Radioastronomia >> Radiotelescopi di Medicina >> Via Fiorentina, 3513 - 40059 Medicina (Bo) >> Tel. 051/6965834 Fax. 051/6965810 >> > > -- Andrea Mattana I.N.A.F. - Istituto di Radioastronomia Radiotelescopi di Medicina Via Fiorentina, 3513 - 40059 Medicina (Bo) Tel. 051/6965834 Fax. 051/6965810
