Hi Heystek,

In addition to what Jack suggests it looks like you may have copied
"tutorial1.slx" to a new model called "tutorial1a.slx" and then immediately
tried to run the casper_xps. From my experience when this is done some of
the gateway in/out blocks do not have a chance to change their hierarchical
names to match the name of the top-level model file. In other words they
are prepended with "tutorial1_" instead of "tutorial1a_" which causes the
CASPER toolflow to throw an error.

To fix this try running "Update diagram" from within Simulink (no
casper_xps) via the "Simulation" menu drop down of your open "tutorial1a"
model file. Then try the casper_xps flow again.

Hope this helps,
Rurik



On Wed, Aug 24, 2016 at 6:18 PM, Jack Hickish <[email protected]> wrote:

> Hi Heystek,
>
> From a clean install, you shouldn't really have this many problems, and I
> suspect all your chmod/chown-ing to/from root is just making everything
> worse.You certainly don't need to run startsg as root (and you shouldn't,
> who knows what code CASPER collaborators have hidden in there!) and if you
> do you'll likely create a bunch of temporary files and directories that you
> now can't write to without root permissions, which will cause pain down the
> road.
>
> It's *possible* that your current problem will go away if you try and
> force your model and library versions up to date. You can do this by
> opening your model, and running "update_casper_blocks(bdroot)" at the
> MATLAB prompt. However, given your permissions problems so far, if it
> were me I would clean out everything and start again.
>
> - Delete your mlib_devel and tutorials_devel directories.
> - Delete (or change ownership to your normal user account) your MATLAB and
> Xilinx configuration directories in ~/.matlab/ and ~/.Xilinx/
> Doing *nothing* with sudo/root:
> - clone from https://github.com/casper-astro/mlib_devel.git
> - Modify startsg to point to your MATLAB/Xilinx installs
> - Make sure you have completed the "tweaks to compile" from
> https://casper.berkeley.edu/wiki/MSSGE_Setup_with_
> Xilinx_14.x_and_Matlab_2012b
>
> Run startsg and try and build something.
>
> If you're trying to build one of the tutorials, make sure you're either
> using the correct library version -- see the instructions at
> https://casper.berkeley.edu/wiki/Tutorials (which I hope has been kept up
> to date) -- or, after opening a tutorial, run
> "update_casper_blocks(bdroot)" at the MATLAB prompt, which will make sure
> the blocks in your library are up to date with your mlib_devel version.
>
> Cheers
> Jack
>
> On Wed, 24 Aug 2016 at 13:21 Heystek Grobler <[email protected]>
> wrote:
>
>> Good evening
>>
>> I am still struggling to get Matlab and Xilinx up and running. I have
>> noticed that the system generator of Xilinx locks the simulink file during
>> compilation. It changes the permissions to access only and the  it can not
>> read and write from it. I have change the permission back to read and write
>> but as soon as it compiles it locks the file again.
>>
>> To try and solve this I have changed the owner of MATLAB and XILINX to
>> "me" and not root. Now I get the following errors that I attached as
>> pictures.
>>
>> I hope that you can help
>>
>> Heystek
>>
>>
>>
>> On Wed, Aug 17, 2016 at 8:45 AM, Adam Isaacson <[email protected]>
>> wrote:
>>
>>> Hi Heystek,
>>>
>>> It appears that line 362 of gen_xps_files.m is commented out, so not
>>> sure what the error pertains to, but still worth checking the pcore compile
>>> tweaks.
>>>
>>> Kind Regards,
>>>
>>> Adam
>>>
>>> On Tue, Aug 16, 2016 at 11:48 PM, Adam Isaacson <[email protected]>
>>> wrote:
>>>
>>>> Hi Heystek,
>>>>
>>>> I am a bit confused where you are now. Are you still getting the
>>>> following error in red below or has this been resolved, but now you are
>>>> encountering another error (Error using gen_xps_files(362)) after you
>>>> applied the chmod command? Please send screen captures of the actual
>>>> errors, thanks.
>>>>
>>>> Details:
>>>> standard exception: XNetlistEngine:
>>>> Exception message could not be parsed:
>>>> com.xilinx.sysgen.netlist.NetlistInternal: couldn't open first
>>>> pass text file at
>>>> /home/heystek/Desktop/tut1/sysgen/sysgen/masterScript423796839757439882
>>>> 5.pl
>>>> line 559'
>>>>
>>>> I had a brief look at line 362 of gen_xps_files.m and it is connected
>>>> with the pcores, so once again I have to ask whether you repeated the
>>>> compile tweaks after you installed ISE 14.7 (
>>>> https://casper.berkeley.edu/wiki/MSSGE_Setup_with_Xilinx_
>>>> 14.x_and_Matlab_2012b)? Also, the tut1 Simulink model that I have been
>>>> working with is a slx file and not an mdl file? What tut 1 file are you
>>>> using?
>>>>
>>>> I am making the assumption that you are based near the Cape Town area?
>>>> If I am correct and if you are still experiencing difficulties why not
>>>> bring your machine and pop over? I think this may be the easiest solution
>>>> :). Just email me directly if you favour this option.
>>>>
>>>> Kind Regards,
>>>>
>>>> Adam
>>>>
>>>> On Tue, Aug 16, 2016 at 9:02 PM, Heystek Grobler <
>>>> [email protected]> wrote:
>>>>
>>>>> Hi James
>>>>>
>>>>> I tried the command and it accepted it. The matlab terminal gives the
>>>>> following error:
>>>>>
>>>>> Error using gen_xps_files(362)
>>>>>
>>>>> Does it make a diffirence if the simulink models are .mdl or .slx?
>>>>>
>>>>> Thank for your help
>>>>>
>>>>> Heystek
>>>>>
>>>>> On Tue, Aug 16, 2016 at 5:40 PM, James Smith <[email protected]> wrote:
>>>>>
>>>>>> Hello Heystek,
>>>>>>
>>>>>> Just to get you an answer quickly, try the following command:
>>>>>>
>>>>>> chmod 777 -R /home/heystek/Desktop/tut1
>>>>>>
>>>>>> If that command makes an error message then add sudo.
>>>>>> It's funny that you should have permissions issues there, if this
>>>>>> doesn't fix things then there might be stranger issues at play.
>>>>>>
>>>>>> Regards,
>>>>>> James
>>>>>>
>>>>>>
>>>>>> On Tue, Aug 16, 2016 at 5:36 PM, Heystek Grobler <
>>>>>> [email protected]> wrote:
>>>>>>
>>>>>>> Hi James and Adam
>>>>>>>
>>>>>>> I got it working. The chmod +x startsg command did the trick. I
>>>>>>> started with the first casper tutorial, but when the system generator
>>>>>>> compiles it the tutorial breaks. It gives two errors.
>>>>>>>
>>>>>>> 1. Design Error  DefaultBlockDiagram  System Generator   Caught
>>>>>>> standard exception
>>>>>>> 2. Block Error    AddSub                       System Generator
>>>>>>>
>>>>>>> The following error log was also generated:
>>>>>>>
>>>>>>> --------------------------------- Version Log
>>>>>>> ----------------------------------
>>>>>>> Version                                 Path
>>>>>>> System Generator                        /opt/Xilinx/14.7/ISE_DS/ISE/
>>>>>>> sysgen
>>>>>>> Matlab 8.0.0.783 (R2012b)               /usr/local/MATLAB/R2012b
>>>>>>> ISE                                     /opt/Xilinx/14.7/ISE_DS/ISE
>>>>>>> ------------------------------------------------------------
>>>>>>> --------------------
>>>>>>> Summary of Errors:
>>>>>>> Error 0001: caught standard exception
>>>>>>>      Block: Unspecified
>>>>>>> ------------------------------------------------------------
>>>>>>> --------------------
>>>>>>>
>>>>>>> Error 0001:
>>>>>>>
>>>>>>> Reported by:
>>>>>>>   Unspecified
>>>>>>>
>>>>>>> Details:
>>>>>>> standard exception: XNetlistEngine:
>>>>>>> Exception message could not be parsed:
>>>>>>> com.xilinx.sysgen.netlist.NetlistInternal: couldn't open first
>>>>>>> pass text file at
>>>>>>> /home/heystek/Desktop/tut1/sysgen/sysgen/
>>>>>>> masterScript4237968397574398825.pl
>>>>>>> line 559'
>>>>>>>
>>>>>>> ------------------------------------------------------------
>>>>>>> --------------------
>>>>>>>
>>>>>>> Do you perhaps have an idea how I can fix it?
>>>>>>>
>>>>>>> Thanks for all the help.
>>>>>>>
>>>>>>> Have a wonderful day.
>>>>>>>
>>>>>>> Heystek
>>>>>>>
>>>>>>>
>>>>>>> On Tue, Aug 16, 2016 at 8:07 AM, James Smith <[email protected]>
>>>>>>> wrote:
>>>>>>>
>>>>>>>> Hello Heystek,
>>>>>>>>
>>>>>>>> This should be a relatively trivial problem to solve:
>>>>>>>>
>>>>>>>> cd ~ # This is a shortcut for your home directory
>>>>>>>> git clone <URL of repository here - either the casper-astro one or
>>>>>>>> the SKA-SA one>
>>>>>>>> cd mlib-devel
>>>>>>>> ./startsg
>>>>>>>>
>>>>>>>> If that doesn't work, then do this:
>>>>>>>> chmod +x startsg
>>>>>>>>
>>>>>>>> Then you should be fine.
>>>>>>>>
>>>>>>>> Regards,
>>>>>>>> James
>>>>>>>>
>>>>>>>>
>>>>>>>> On Mon, Aug 15, 2016 at 7:46 PM, Heystek Grobler <
>>>>>>>> [email protected]> wrote:
>>>>>>>>
>>>>>>>>> Hi Adam and James
>>>>>>>>>
>>>>>>>>> I am working on my personal computer. I will ask a IT guy to help
>>>>>>>>> me with the privileges and also clone the mlib-devel into the
>>>>>>>>> home directory and try to run it again.
>>>>>>>>>
>>>>>>>>> Thanks for all your help.
>>>>>>>>>
>>>>>>>>> Heystek
>>>>>>>>>
>>>>>>>>> On Mon, Aug 15, 2016 at 12:58 PM, Adam Isaacson <
>>>>>>>>> [email protected]> wrote:
>>>>>>>>>
>>>>>>>>>> Hi Heystek,
>>>>>>>>>>
>>>>>>>>>> This issue is not with your script, but your linux permissions. I
>>>>>>>>>> suggest you follow what James suggests. The fact that you can't run 
>>>>>>>>>> sudo
>>>>>>>>>> though means that you may need your IT guy to give you sudo rights, 
>>>>>>>>>> but if
>>>>>>>>>> you are working off the university server that may be an issue - as 
>>>>>>>>>> James
>>>>>>>>>> says, you shouldn't need this if you install into your home 
>>>>>>>>>> directory.
>>>>>>>>>>
>>>>>>>>>> Kind Regards,
>>>>>>>>>>
>>>>>>>>>> Adam
>>>>>>>>>>
>>>>>>>>>> On Mon, Aug 15, 2016 at 11:27 AM, James Smith <[email protected]>
>>>>>>>>>> wrote:
>>>>>>>>>>
>>>>>>>>>>> Hello Heystek,
>>>>>>>>>>>
>>>>>>>>>>> It would be a bit easier to debug if you posted the terminal
>>>>>>>>>>> session, along with the commands you ran.
>>>>>>>>>>>
>>>>>>>>>>> Also, please run "ls -l" in the directory and post that as well.
>>>>>>>>>>> It might just be that you need to give the file executable 
>>>>>>>>>>> permissions.
>>>>>>>>>>>
>>>>>>>>>>> Regards,
>>>>>>>>>>> James
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>> On Mon, Aug 15, 2016 at 11:24 AM, Heystek Grobler <
>>>>>>>>>>> [email protected]> wrote:
>>>>>>>>>>>
>>>>>>>>>>>> Hi Adam
>>>>>>>>>>>>
>>>>>>>>>>>> I modified the startsg file. When I run it I get the error in
>>>>>>>>>>>> the terminal "Permission denied". When I run the startsg file as 
>>>>>>>>>>>> sudo I get
>>>>>>>>>>>> the error "command not found".
>>>>>>>>>>>>
>>>>>>>>>>>> I have attached my modified startsg file.
>>>>>>>>>>>>
>>>>>>>>>>>> Do you perhaps have any ideas of how to solve it?
>>>>>>>>>>>>
>>>>>>>>>>>> Sorry for the inconvenience
>>>>>>>>>>>>
>>>>>>>>>>>> Heystek
>>>>>>>>>>>>
>>>>>>>>>>>> On Mon, Aug 15, 2016 at 11:10 AM, Adam Isaacson <
>>>>>>>>>>>> [email protected]> wrote:
>>>>>>>>>>>>
>>>>>>>>>>>>> Hi Heystek,
>>>>>>>>>>>>>
>>>>>>>>>>>>> Nope, just run the ./startsg and matlab will run the startup.m
>>>>>>>>>>>>> file for you when it opens. You should already have both the 
>>>>>>>>>>>>> startsg and
>>>>>>>>>>>>> startup.m files, but I gave you mine as I know it works.
>>>>>>>>>>>>>
>>>>>>>>>>>>> Kind Regards,
>>>>>>>>>>>>>
>>>>>>>>>>>>> Adam
>>>>>>>>>>>>>
>>>>>>>>>>>>> On Mon, Aug 15, 2016 at 10:58 AM, Heystek Grobler <
>>>>>>>>>>>>> [email protected]> wrote:
>>>>>>>>>>>>>
>>>>>>>>>>>>>> Hi Adam
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> I will try these files! Do I run the startup.m file in matlab
>>>>>>>>>>>>>> as well?
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> Have a nice day
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> Heystek
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> On Mon, Aug 15, 2016 at 9:04 AM, Adam Isaacson <
>>>>>>>>>>>>>> [email protected]> wrote:
>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> Hi Heystek,
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> No worries. I was in your position just a few months ago :).
>>>>>>>>>>>>>>> I have attached my matlab startup scripts (startsg and 
>>>>>>>>>>>>>>> startup.m). These
>>>>>>>>>>>>>>> must be placed in the "mlib_devel" directory. You will probably 
>>>>>>>>>>>>>>> have to
>>>>>>>>>>>>>>> change the paths to where your installs are.
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> All you need to do is the following:
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> 1) Startup matlab R2012b, by running the startsg script.
>>>>>>>>>>>>>>> Using the Ubuntu terminal, in the "mlib_devel" directory type: 
>>>>>>>>>>>>>>> "./startsg".
>>>>>>>>>>>>>>> This should startup matlab. There should be a message saying 
>>>>>>>>>>>>>>> that "system
>>>>>>>>>>>>>>> generator currently found installed in matlab default path..."
>>>>>>>>>>>>>>> 2) Type in "simulink" in the command window.
>>>>>>>>>>>>>>> 3) The Simulink Library Browser will open. Browse to where
>>>>>>>>>>>>>>> your model is located and select the *.slx file.
>>>>>>>>>>>>>>> 4) The model should open. Press "Ctrl + D" to check for any
>>>>>>>>>>>>>>> errors. There should be no errors.
>>>>>>>>>>>>>>> 5) Type in "casper_xps" in the command window. The casper
>>>>>>>>>>>>>>> XPS window should pop up. Make sure all boxes are ticked under 
>>>>>>>>>>>>>>> "ISE Design
>>>>>>>>>>>>>>> Flow Choice:" and then click on "Run XPS". This will run the 
>>>>>>>>>>>>>>> system
>>>>>>>>>>>>>>> generator as part of the process, the Xilinx ISE and generate 
>>>>>>>>>>>>>>> the relevant
>>>>>>>>>>>>>>> bit, fpg files.
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> I have also attached scripts if you just want to run the
>>>>>>>>>>>>>>> programs individually - you will need to edit the path to where 
>>>>>>>>>>>>>>> your
>>>>>>>>>>>>>>> installs are.
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> Good luck. This should get you going. If the scripts bomb
>>>>>>>>>>>>>>> out then it is likely that your paths are not correct - check 
>>>>>>>>>>>>>>> that first.
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> Kind Regards,
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> Adam
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> On Sun, Aug 14, 2016 at 8:26 PM, Heystek Grobler <
>>>>>>>>>>>>>>> [email protected]> wrote:
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>> Hi Adam
>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>> I got ISE to run. It open up die GUI. How do I start the
>>>>>>>>>>>>>>>> sysgen with MATLAB?
>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>> Sorry about the queations.
>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>> Thank you for your help
>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>> Heystek
>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>> On Sun, Aug 14, 2016 at 12:06 PM, Heystek Grobler <
>>>>>>>>>>>>>>>> [email protected]> wrote:
>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>> Good day Adam
>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>> I have been working through the documents you send me. I
>>>>>>>>>>>>>>>>> cant open the ISE IDE. As soon as I run the script I get the 
>>>>>>>>>>>>>>>>> following
>>>>>>>>>>>>>>>>> error:
>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>> command not found
>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>> I am new to Linux and Xilinx.
>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>> Have a good day
>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>> Heystek
>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>> On Mon, Aug 8, 2016 at 3:31 PM, Adam Isaacson <
>>>>>>>>>>>>>>>>> [email protected]> wrote:
>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>> Hi Heystek,
>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>> You mentioned that you were using the ROACH2 board. This
>>>>>>>>>>>>>>>>>> contains a Virtex 6 device. Vivado only works with Virtex 7 
>>>>>>>>>>>>>>>>>> onwards. I
>>>>>>>>>>>>>>>>>> would suggest if you are going to target the ROACH 2 that 
>>>>>>>>>>>>>>>>>> you use Xilinx
>>>>>>>>>>>>>>>>>> ISE 14.7.
>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>> You will need to work with ISE 14.7 and not Vivado.  We
>>>>>>>>>>>>>>>>>> have just begun to use Vivado for our Virtex 7 board e.g  
>>>>>>>>>>>>>>>>>> SKARAB. As far as
>>>>>>>>>>>>>>>>>> I am aware, all the the ROACH2 development in SKA-SA has 
>>>>>>>>>>>>>>>>>> been done using
>>>>>>>>>>>>>>>>>> Xilinx ISE 14., as it supports Virtex 6 devices.
>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>> Kind Regards,
>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>> Adam
>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>> On Mon, Aug 8, 2016 at 3:13 PM, Heystek Grobler <
>>>>>>>>>>>>>>>>>> [email protected]> wrote:
>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>> Good day Adam
>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>> I am using Ubuntu 14.04 LTS with MATLAB 2012B. Im using
>>>>>>>>>>>>>>>>>>> the Vivado suite that came with a Zed-Board (Vivado 2013.4).
>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>> The error I am receiving from MATLAB at startup is:
>>>>>>>>>>>>>>>>>>> Undefined function 'lAddSysgen' for input arguments of
>>>>>>>>>>>>>>>>>>> type 'char'.
>>>>>>>>>>>>>>>>>>> > In matlabrc at 205
>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>> The errors I get from the system generator is:
>>>>>>>>>>>>>>>>>>> 1. Design Error - Default block diagram
>>>>>>>>>>>>>>>>>>> 2. Block Error - AddSub
>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>> These errors occurs with the first tutorial from CASPER.
>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>> I looked at the "tweaks to compile" but everything seems
>>>>>>>>>>>>>>>>>>> ok.
>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>> I will use the guides you have attached in the previous
>>>>>>>>>>>>>>>>>>> email.
>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>> I appreciate your help!!
>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>> Heystek
>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>> On Mon, Aug 8, 2016 at 2:30 PM, Adam Isaacson <
>>>>>>>>>>>>>>>>>>> [email protected]> wrote:
>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>> Apologies, that should of been Ubuntu 14.04 LTS and
>>>>>>>>>>>>>>>>>>>> Matlab R2015b...
>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>> On Mon, Aug 8, 2016 at 2:28 PM, Adam Isaacson <
>>>>>>>>>>>>>>>>>>>> [email protected]> wrote:
>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>> Hi Heystek,
>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>> What OS are you using? I am using Ubuntu 4.04 LTS.
>>>>>>>>>>>>>>>>>>>>> What repo are you using? I am using
>>>>>>>>>>>>>>>>>>>>> https://github.com/ska-sa/mlib_devel. What version of
>>>>>>>>>>>>>>>>>>>>> Matlab and Xilinx are you using? I am using Matlab R2012b 
>>>>>>>>>>>>>>>>>>>>> and R2105b. I am
>>>>>>>>>>>>>>>>>>>>> using Xilinx ISE 14.7. I wrote these How To docs which 
>>>>>>>>>>>>>>>>>>>>> may or may not come
>>>>>>>>>>>>>>>>>>>>> in handy.
>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>> 1) Matlab 2012b and 2015b Installation:
>>>>>>>>>>>>>>>>>>>>> https://drive.google.com/open?id=
>>>>>>>>>>>>>>>>>>>>> 18BBkoWlSGeuK8BV1UlSnRJIYzlOEWUhqTlF_zAePTj0
>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>> 2) Xilinx ISE 14.7 Installation:
>>>>>>>>>>>>>>>>>>>>> https://drive.google.com/open?id=
>>>>>>>>>>>>>>>>>>>>> 1o7Wl7wzB7VE1Cckk60B35WerJvl5crXa7Q5xbcoYgE0
>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>> This should be read in conjunction with the CASPER
>>>>>>>>>>>>>>>>>>>>> wiki page - https://casper.berkeley.edu/
>>>>>>>>>>>>>>>>>>>>> wiki/MSSGE_Setup_with_Xilinx_14.x_and_Matlab_2012b -
>>>>>>>>>>>>>>>>>>>>> did you follow "tweaks to be able to compile"?
>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>> Kind Regards,
>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>> Adam
>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>> On Mon, Aug 8, 2016 at 1:53 PM, Heystek Grobler <
>>>>>>>>>>>>>>>>>>>>> [email protected]> wrote:
>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>>> Good Day
>>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>>> My name is Heystek Grobler. I am an electrical en
>>>>>>>>>>>>>>>>>>>>>> electronic engineering science student and for my final 
>>>>>>>>>>>>>>>>>>>>>> year project
>>>>>>>>>>>>>>>>>>>>>> (skripsie) I'm developing a wideband spectrometer on a 
>>>>>>>>>>>>>>>>>>>>>> ROACH-2 board.
>>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>>> Currently I have a problem with Xilinx System
>>>>>>>>>>>>>>>>>>>>>> Generator and MATLAB. The Simulink Model runs as a 
>>>>>>>>>>>>>>>>>>>>>> simulation but as soon
>>>>>>>>>>>>>>>>>>>>>> as I run it in Xilinx System Generator to compile it for 
>>>>>>>>>>>>>>>>>>>>>> the board it
>>>>>>>>>>>>>>>>>>>>>> crashes and gives a "design error" as and "block error".
>>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>>> I was hoping that if possible, that you could provide
>>>>>>>>>>>>>>>>>>>>>> me with assistance to get Xilinx and Simulink up and 
>>>>>>>>>>>>>>>>>>>>>> running. So far I
>>>>>>>>>>>>>>>>>>>>>> followed the CASPER tutorials but got stuck with this 
>>>>>>>>>>>>>>>>>>>>>> problem/
>>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>>> I hope to hear from you soon.
>>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>>> Have a wonderful day
>>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>> --
>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>> Adam Isaacson
>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>> DBE: FPGA Engineer
>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>> SKA-SA
>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>> 3rd Floor
>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>> The Park
>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>> Park Road
>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>> Pinelands
>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>> 7405
>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>> Tel: +27215067300 (W)
>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>> Fax: +27215067375 (W)
>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>> Cell: +27825639602
>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>> --
>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>> Adam Isaacson
>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>> DBE: FPGA Engineer
>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>> SKA-SA
>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>> 3rd Floor
>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>> The Park
>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>> Park Road
>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>> Pinelands
>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>> 7405
>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>> Tel: +27215067300 (W)
>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>> Fax: +27215067375 (W)
>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>> Cell: +27825639602
>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>> --
>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>> Adam Isaacson
>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>> DBE: FPGA Engineer
>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>> SKA-SA
>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>> 3rd Floor
>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>> The Park
>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>> Park Road
>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>> Pinelands
>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>> 7405
>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>> Tel: +27215067300 (W)
>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>> Fax: +27215067375 (W)
>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>> Cell: +27825639602
>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> --
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> Adam Isaacson
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> DBE: FPGA Engineer
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> SKA-SA
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> 3rd Floor
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> The Park
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> Park Road
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> Pinelands
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> 7405
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> Tel: +27215067300 (W)
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> Fax: +27215067375 (W)
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> Cell: +27825639602
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>
>>>>>>>>>>>>>>
>>>>>>>>>>>>>
>>>>>>>>>>>>>
>>>>>>>>>>>>> --
>>>>>>>>>>>>>
>>>>>>>>>>>>> Adam Isaacson
>>>>>>>>>>>>>
>>>>>>>>>>>>> DBE: FPGA Engineer
>>>>>>>>>>>>>
>>>>>>>>>>>>> SKA-SA
>>>>>>>>>>>>>
>>>>>>>>>>>>> 3rd Floor
>>>>>>>>>>>>>
>>>>>>>>>>>>> The Park
>>>>>>>>>>>>>
>>>>>>>>>>>>> Park Road
>>>>>>>>>>>>>
>>>>>>>>>>>>> Pinelands
>>>>>>>>>>>>>
>>>>>>>>>>>>> 7405
>>>>>>>>>>>>>
>>>>>>>>>>>>>
>>>>>>>>>>>>> Tel: +27215067300 (W)
>>>>>>>>>>>>>
>>>>>>>>>>>>> Fax: +27215067375 (W)
>>>>>>>>>>>>>
>>>>>>>>>>>>> Cell: +27825639602
>>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>> --
>>>>>>>>>>
>>>>>>>>>> Adam Isaacson
>>>>>>>>>>
>>>>>>>>>> DBE: FPGA Engineer
>>>>>>>>>>
>>>>>>>>>> SKA-SA
>>>>>>>>>>
>>>>>>>>>> 3rd Floor
>>>>>>>>>>
>>>>>>>>>> The Park
>>>>>>>>>>
>>>>>>>>>> Park Road
>>>>>>>>>>
>>>>>>>>>> Pinelands
>>>>>>>>>>
>>>>>>>>>> 7405
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>> Tel: +27215067300 (W)
>>>>>>>>>>
>>>>>>>>>> Fax: +27215067375 (W)
>>>>>>>>>>
>>>>>>>>>> Cell: +27825639602
>>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>
>>>>>>>
>>>>>>
>>>>>
>>>>
>>>>
>>>> --
>>>>
>>>> Adam Isaacson
>>>>
>>>> DBE: FPGA Engineer
>>>>
>>>> SKA-SA
>>>>
>>>> 3rd Floor
>>>>
>>>> The Park
>>>>
>>>> Park Road
>>>>
>>>> Pinelands
>>>>
>>>> 7405
>>>>
>>>>
>>>> Tel: +27215067300 (W)
>>>>
>>>> Fax: +27215067375 (W)
>>>>
>>>> Cell: +27825639602
>>>>
>>>
>>>
>>>
>>> --
>>>
>>> Adam Isaacson
>>>
>>> DBE: FPGA Engineer
>>>
>>> SKA-SA
>>>
>>> 3rd Floor
>>>
>>> The Park
>>>
>>> Park Road
>>>
>>> Pinelands
>>>
>>> 7405
>>>
>>>
>>> Tel: +27215067300 (W)
>>>
>>> Fax: +27215067375 (W)
>>>
>>> Cell: +27825639602
>>>
>>
>>

Reply via email to