Hi Jack

I have a ROACH1 Rev.3, S/N 040433, and I'm using the file system that came
in the SD-Card to use ROACH.

Is this what I need to update?

Also, I am using corr-0.7.3 and katcp-0.3.4.

What are the correct versions of corr and katcp for my ROACH?  Or, should I
use casperfpga?

Best Regard

Rolando

2016-12-04 15:30 GMT-06:00 Jack Hickish <[email protected]>:

> Hi Rolando,
>
> If I had to guess, I'd say there is a problem with the version of the
> python katcp/corr libraries you're using, and the version of tcpborphserver
> running on your ROACH. Do you know the versions of these bits of code that
> you're using?
>
> Cheers
> Jack
>
> On Thu, 1 Dec 2016 at 16:52 Rolando Paz <[email protected]> wrote:
>
>> Hello again
>>
>> I'm experimenting with the 10G port, however when I tried to run the
>> tut_2, the following problem arises:
>>
>> rolando@rolando-MS-7815:~/codigo_ROACH/tut2$ sudo python tut2.py
>> 192.168.100.2 -s
>> [sudo] password for rolando:
>> Connecting to server 192.168.100.2...  ok
>>
>> ------------------------
>> Programming FPGA... ok
>> ---------------------------
>> Disabling output... done
>> ---------------------------
>> Port 0 linkup:  True
>> Port 3 linkup:  True
>> ---------------------------
>> Configuring receiver core... <type 'exceptions.RuntimeError'>
>> ('Request tap-start failed.\n  Request: ?tap-start tap0 gbe3 192.168.3.16
>> 60000 02:02:C0:A8:03:10\n  Reply: !tap-start fail.',)
>> Request tap-start failed.
>>   Request: ?tap-start tap0 gbe3 192.168.3.16 60000 02:02:C0:A8:03:10
>>   Reply: !tap-start fail.
>> FAILURE DETECTED. Log entries:
>> 192.168.100.2: Starting thread Thread-1
>> 192.168.100.2: #version poco-0.1
>> 192.168.100.2: #build-state poco-0.2804
>> 192.168.100.2: ?progdev tut2.bof
>>
>> 192.168.100.2: !progdev ok 528
>> 192.168.100.2: Programming FPGA with tut2.bof... ok.
>> 192.168.100.2: ?write pkt_sim_enable 0 \0\0\0\0
>>
>> 192.168.100.2: !write ok
>> 192.168.100.2: ?read pkt_sim_enable 0 4
>>
>> 192.168.100.2: !read ok \0\0\0\0
>> 192.168.100.2: Write        0 to register pkt_sim_enable at offset 0 ok.
>> 192.168.100.2: ?read gbe0_linkup 0 4
>>
>> 192.168.100.2: !read ok \0\0\0
>> 192.168.100.2: ?read gbe3_linkup 0 4
>>
>> 192.168.100.2: !read ok \0\0\0
>> 192.168.100.2: Starting tgtap driver instance for tap-start: tap0 gbe3
>> 192.168.3.16 60000 02:02:C0:A8:03:10
>> 192.168.100.2: ?tap-start tap0 gbe3 192.168.3.16 60000 02:02:C0:A8:03:10
>>
>> 192.168.100.2: #log error 2416053613647 poco register\_tap0\_seems\_
>> unavailable
>> 192.168.100.2: !tap-start fail
>> 192.168.100.2: Request tap-start failed.
>>   Request: ?tap-start tap0 gbe3 192.168.3.16 60000 02:02:C0:A8:03:10
>>   Reply: !tap-start fail.
>> None
>> rolando@rolando-MS-7815:~/codigo_ROACH/tut2$
>>
>>
>> How do I solve the problem?
>>
>> I will appreciate any comments ...
>>
>> Regards
>>
>> RP
>>
>>
>>

Reply via email to