:-)

I have installed this versions:

construct-2.5.2
corr-0.7.3
katcp-0.3.4
h5py-2.6.0
pyephem-3.7.6.0

If I install katcp-0.6.0 some problems arise, so I had to install
katcp-0.3.4. so, I am thinking update my filesystem version, because can be
outdated?

Regards

Rolando






2016-12-05 14:04 GMT-06:00 Jack Hickish <[email protected]>:

> Hi Rolando,
>
> Nice work!
>
> My advice - if everything works, don't touch it! It would be good to note
> your currently working combination of package versions, in case you have
> problems in the future.
>
> Cheers
> Jack
>
> On Mon, 5 Dec 2016, 12:01 Rolando Paz, <[email protected]> wrote:
>
>> Hi Jack
>>
>> I found this email http://www.mail-archive.com/[email protected]/
>> msg02504.html
>>
>> Then I used minicom and I replaced tcpborphserver2
>>
>> root@roach:/usr/local/sbin# ls
>> fancontrol      pwmconfig  sensors-detect    tcpborphserver2      tgtap
>> flash_eraseall  sensord    tb2server-allfix  tcpborphserver2_old
>> root@roach:/usr/local/sbin#
>>
>> After this worked tut2!
>>
>> However, should I upgrade the versions of corr and katcp and filesystem?
>>
>> This is the output of ?help
>>
>> rolando@rolando-MS-7815:~$ telnet 192.168.100.2 7147
>> Trying 192.168.100.2...
>> Connected to 192.168.100.2.
>> Escape character is '^]'.
>> #version poco-0.1
>> #build-state poco-0.0a271150300
>> ?help
>> #help sensor-dump dump\_sensor\_tree\_(?sensor-dump)
>> #help sensor-value query\_a\_sensor\_(?sensor-value\_sensor)
>> #help sensor-sampling configure\_sensor\_(?sensor-
>> sampling\_sensor\_[strategy\_[parameter]])
>> #help sensor-list lists\_available\_sensors\_(?sensor-list\_[sensor])
>> #help client-list displays\_client\_list\_(?client-list)
>> #help tap-stop stop\_a\_tgtap\_instance\_(?tap-stop\_register-name)
>> #help tap-start start\_a\_tgtap\_instance\_(?tap-start\_tap-device\_
>> register-name\_ip-address\_[port\_[mac]])
>> #help wordwrite writes\_a\_word\_(?wordwrite\_
>> register-name\_word-offset\_payload\_...)
>> #help wordread reads\_a\_word\_(?wordread\_register-name\_word-offset\_
>> length)
>> #help sysinit writes\_the\_timing\_ctl\_register\_that\_resets\_the\_
>> entire\_system\_(?sysinit)
>> #help write write\_a\_given\_payload\_to\_an\_offset\_in\_a\_register\_(
>> ?write\_register-name\_register-offset\_data-payload)
>> #help bulkread reads\_a\_given\_number\_of\_bytes\_from\_an\_offset\_in\_
>> a\_register\_in\_a\_form\_suitable\_for\_large\_transfers\_(?bulkread\_
>> register-name\_[register-offset\_[byte-count]])
>> #help read reads\_a\_given\_number\_of\_bytes\_from\_an\_offset\_in\_
>> a\_register\_(?read\_register-name\_[register-offset\_[byte-count]])
>> #help echotest basic\_network\_echo\_tester\_
>> (?echotest\_ip-address\_echo-port\_byte-count)
>> #help listdev lists\_available\_registers\_(?listdev)
>> #help delbof deletes\_a\_gateware\_image\_(?delbof\_image-file)
>> #help uploadbof upload\_a\_gateware\_image\_(?
>> uploadbof\_net-port\_filename\_[size])
>> #help listbof lists\_available\_gateware\_images\_(?listbof)
>> #help status reports\_if\_gateware\_has\_been\_programmed\_(?status)
>> #help progdev programs\_a\_gateware\_image\_(?progdev\_[image-file])
>> #help mode mode\_change\_command\_(?mode\_[new-mode])
>> #help watchdog pings\_the\_system\_(?watchdog)
>> #help log-level sets\_the\_minimum\_reported\_
>> log\_priority\_(?log-level\_[priority])
>> #help help displays\_this\_help\_(?help\_[command])
>> #help restart restarts\_the\_system\_(?restart)
>> #help halt shuts\_the\_system\_down\_(?halt)
>> !help ok 26
>>
>> Regards
>>
>> Rolando
>>
>>
>> 2016-12-05 12:30 GMT-06:00 Jack Hickish <[email protected]>:
>>
>> Hi Rolando,
>> Can you telnet into the roach using the command
>>
>> telnet <roach ip address> 7147
>>
>> You should be greeted by a welcome prompt. In the prompt, type
>>
>> ?help
>>
>> If you can paste the output of these commands in an email, maybe I can
>> find you a version of the katcpserver which will work (assuming that's the
>> problem)
>>
>> Cheers
>> Jack
>>
>> On Mon, 5 Dec 2016, 09:30 Rolando Paz, <[email protected]> wrote:
>>
>> Hi Jack
>>
>> I have a ROACH1 Rev.3, S/N 040433, and I'm using the file system that
>> came in the SD-Card to use ROACH.
>>
>> Is this what I need to update?
>>
>> Also, I am using corr-0.7.3 and katcp-0.3.4.
>>
>> What are the correct versions of corr and katcp for my ROACH?  Or, should
>> I use casperfpga?
>>
>> Best Regard
>>
>> Rolando
>>
>> 2016-12-04 15:30 GMT-06:00 Jack Hickish <[email protected]>:
>>
>> Hi Rolando,
>>
>> If I had to guess, I'd say there is a problem with the version of the
>> python katcp/corr libraries you're using, and the version of tcpborphserver
>> running on your ROACH. Do you know the versions of these bits of code that
>> you're using?
>>
>> Cheers
>> Jack
>>
>> On Thu, 1 Dec 2016 at 16:52 Rolando Paz <[email protected]> wrote:
>>
>> Hello again
>>
>> I'm experimenting with the 10G port, however when I tried to run the
>> tut_2, the following problem arises:
>>
>> rolando@rolando-MS-7815:~/codigo_ROACH/tut2$ sudo python tut2.py
>> 192.168.100.2 -s
>> [sudo] password for rolando:
>> Connecting to server 192.168.100.2...  ok
>>
>> ------------------------
>> Programming FPGA... ok
>> ---------------------------
>> Disabling output... done
>> ---------------------------
>> Port 0 linkup:  True
>> Port 3 linkup:  True
>> ---------------------------
>> Configuring receiver core... <type 'exceptions.RuntimeError'>
>> ('Request tap-start failed.\n  Request: ?tap-start tap0 gbe3 192.168.3.16
>> 60000 02:02:C0:A8:03:10\n  Reply: !tap-start fail.',)
>> Request tap-start failed.
>>   Request: ?tap-start tap0 gbe3 192.168.3.16 60000 02:02:C0:A8:03:10
>>   Reply: !tap-start fail.
>> FAILURE DETECTED. Log entries:
>> 192.168.100.2: Starting thread Thread-1
>> 192.168.100.2: #version poco-0.1
>> 192.168.100.2: #build-state poco-0.2804
>> 192.168.100.2: ?progdev tut2.bof
>>
>> 192.168.100.2: !progdev ok 528
>> 192.168.100.2: Programming FPGA with tut2.bof... ok.
>> 192.168.100.2: ?write pkt_sim_enable 0 \0\0\0\0
>>
>> 192.168.100.2: !write ok
>> 192.168.100.2: ?read pkt_sim_enable 0 4
>>
>> 192.168.100.2: !read ok \0\0\0\0
>> 192.168.100.2: Write        0 to register pkt_sim_enable at offset 0 ok.
>> 192.168.100.2: ?read gbe0_linkup 0 4
>>
>> 192.168.100.2: !read ok \0\0\0
>> 192.168.100.2: ?read gbe3_linkup 0 4
>>
>> 192.168.100.2: !read ok \0\0\0
>> 192.168.100.2: Starting tgtap driver instance for tap-start: tap0 gbe3
>> 192.168.3.16 60000 02:02:C0:A8:03:10
>> 192.168.100.2: ?tap-start tap0 gbe3 192.168.3.16 60000 02:02:C0:A8:03:10
>>
>> 192.168.100.2: #log error 2416053613647 poco register\_tap0\_seems\_
>> unavailable
>> 192.168.100.2: !tap-start fail
>> 192.168.100.2: Request tap-start failed.
>>   Request: ?tap-start tap0 gbe3 192.168.3.16 60000 02:02:C0:A8:03:10
>>   Reply: !tap-start fail.
>> None
>> rolando@rolando-MS-7815:~/codigo_ROACH/tut2$
>>
>>
>> How do I solve the problem?
>>
>> I will appreciate any comments ...
>>
>> Regards
>>
>> RP
>>
>>
>>
>>
>>

Reply via email to