tcpborphserver is a server designed to control roaches. It speaks KATCP over port 7147. There are three versions of tcpborphserver at the moment.
ps; however i dont have a clue on what that means :) On Thu, Aug 30, 2018 at 3:19 AM Nivek Ghazi <nivekgh...@outlook.com> wrote: > > Hi Wesley, Danny, > > It don't think its was a power issue as the RPi 3b+ was getting its power > from the 40 pin connection to the SNAP board. I measured the current draw to > be around 1.1A at idle when using a RPi 3b and around 1.8A when running > firmware. These measurements were made by connecting a multimeter between a > power supply and the 12v input of the SNAP board. It's more of a total > current draw and not the current draw of RPi since I didn't want to hack up a > connector. The issue looks like an incompatible image. So, after writing > Danny's image with the dd command and some failed boot's (kept getting an > error of something like kernel panic but it happened so fast I didn't get to > read the whole message before it shutdowns), I wrote the image on a > semi-fresh SD card with etcher and booted, install casperfpga and the SNAP > board programmed successfully. It would be nice to get an official image. > > Also, out of curiosity. What is tcpborphserver? > > thanks, > > Nivek > > > On 29/08/2018 12:35, Danny Price wrote: > > Hi Nivek, > > I had the same issue, I think the image is not compatible with RPi3. > > I worked around this, and got tcpborphserver running on the stock RPi3 image, > try this: > https://drive.google.com/open?id=19ZSioiAVmYqa1w6SHvdIwo47Wi4wGefI > > Let me know if this works for you too; in which case might be worth making a > more official release. > > Cheers, > Danny > > PS: I burned this using etcher, which is a neat UI tool > (https://etcher.io/) > > On 29 August 2018 at 8:28:51 pm, Wesley New (wes...@ska.ac.za) wrote: > > Hi Nivek, > > I would take a read through this > https://raspberrypi.stackexchange.com/questions/19354/raspberry-pi-with-boots-up-with-rainbow-screen > > Also confirm that you have a power supply that can deliver 2.5A at 5v. > > I have not used that image before, but you can plug the card into your PC and > check if it mounts correctly and the boot partition is there. > > > > > > Wesley New > South African SKA Project > +2721 506 7300 > www.ska.ac.za > > > > On Wed, Aug 29, 2018 at 12:21 PM, Nivek Ghazi <nivekgh...@outlook.com> wrote: >> >> Hey Casper people, >> >> So, I recently got a raspberry pi 3 b+ and looking to get it working >> with the SNAP board. I've download the image from the SNAP bringup >> tutorial and tried to get it to boot but it fails (the raspberry pi >> basically just outputs a rainbow pattern on the monitor with the red >> power led on and stays there). I'm guessing it fails because the image >> was not compiled to run on this new raspberry pi. Is it possible to get >> the raspberry pi 3 b+ working with the SNAP board? >> >> thanks, >> >> Nivek Ghazi >> >> -- >> You received this message because you are subscribed to the Google Groups >> "casper@lists.berkeley.edu" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to casper+unsubscr...@lists.berkeley.edu. >> To post to this group, send email to casper@lists.berkeley.edu. > > > -- > You received this message because you are subscribed to the Google Groups > "casper@lists.berkeley.edu" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to casper+unsubscr...@lists.berkeley.edu. > To post to this group, send email to casper@lists.berkeley.edu. > > -- > You received this message because you are subscribed to the Google Groups > "casper@lists.berkeley.edu" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to casper+unsubscr...@lists.berkeley.edu. > To post to this group, send email to casper@lists.berkeley.edu. > > > -- > You received this message because you are subscribed to the Google Groups > "casper@lists.berkeley.edu" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to casper+unsubscr...@lists.berkeley.edu. > To post to this group, send email to casper@lists.berkeley.edu. -- You received this message because you are subscribed to the Google Groups "casper@lists.berkeley.edu" group. To unsubscribe from this group and stop receiving emails from it, send an email to casper+unsubscr...@lists.berkeley.edu. To post to this group, send email to casper@lists.berkeley.edu.
