jack,

did you do all this work?
hong ?        brian ?

dan


On Mon, Jan 14, 2019 at 7:23 PM Jack Hickish <[email protected]> wrote:

> Hi CASPERites,
>
> I know a few of you have been playing around with the VCU118 Virtex
> Ultrascale Plus dev board. For a while the toolflow has been able to
> compile designs for this board, but without any support for accessing the
> software registers / brams in the generated bitstream (making the toolflow
> effectively useless).
>
> The VCU118 branch of mlib_devel --
> https://github.com/casper-astro/mlib_devel/tree/vcu118 -- now supports
> compiling a VCU118 design with an embedded microblaze core, which allows
> you to talk to the board using the standard casperfpga library.
>
> Note the following caveats --
>
> - use the latest version of casperfpga (
> https://github.com/casper-astro/casperfpga, currently at commit ee9c43f )
> and install the dependencies with `pip install -r requirements.txt` before
> installing casperfpga with `python setup.py install`. I strongly recommend
> using a python virtual environment to be sure you are using the right
> libraries. Note that the dependencies include a custom tftpy **not the one
> obtained with `pip install tftpy`.
> - casperfpga comms are (currently) only supported through the VCU118's
> 1GbE RJ45 port
> - You must instantiate a 1GbE yellow block in your design - see
> https://github.com/casper-astro/mlib_devel/blob/vcu118/jasper_library/test_models/test_onegbe.slx
> for a simple example
> - You must check the "enable microblaze" checkbox in the VCU118
> configuration block.
> - I tested using MATLAB 2017b and Vivado 2018.2. Use other versions of
> software at your own risk. In particular, other versions of Vivado will
> probably fail spectacularly.
> - Your VCU118 will attempt to DHCP an IP address on boot. It has the MAC
> address 02:03:04:05:01:18 . Once DHCP is complete, you should be able to
> ping the board.
> - Debugging information can be obtained on the VCU's USB UART port, with
> your serial interface set to 115200 8N1.
> - You must program the bitstream generated by the toolflow manually via
> JTAG in vivado (the bitstream can be found at
> <build-directory>/myproj/myproj.runs/impl_1/top.bit). casperfpga's
> upload_to_ram_and_program command **will NOT work**.
>
> There is still a bunch of work to do to support this board -- for example:
> supporting writing an image to the onboard flash, getting a unique
> per-board MAC address, supporting other peripherals (notably 100GbE, which
> some CASPERites are already working on, and an FMC ADC from ASIAA), etc.
> etc. But for now, hopefully this zeroth-order support will help with other
> yellow block development efforts, by allowing you to probe the board
> without resorting to the joy of the vivado logic analyzer.
>
> Further help always appreciated, and feel free to shout when the above
> doesn't work for you.
>
> Jack
>
> --
> You received this message because you are subscribed to the Google Groups "
> [email protected]" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to [email protected].
> To post to this group, send email to [email protected].
>

-- 
You received this message because you are subscribed to the Google Groups 
"[email protected]" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to [email protected].
To post to this group, send email to [email protected].

Reply via email to