This is one of those difficult curves for everyone! Very often, we set our sights really high on some twisted solution, or something strange that "must" be happening. Most things are really very basic when it comes down to it! Never forget the basics!
Glad it's working well now! :) Have a Happy New Year! Scott -----Original Message----- From: Tandou Mohamed [mailto:[EMAIL PROTECTED] Sent: Wednesday, December 27, 2006 12:57 PM To: [EMAIL PROTECTED]; [email protected] Subject: RE: [OSL | CCIE_RS] IPEXPERT LAB 38 You're right i never thought about this. Bingo everything is working fine now. This part of lab was a tricky one for me. thanks a lot. MT >From: "Scott Morris" <[EMAIL PROTECTED]> >Reply-To: <[EMAIL PROTECTED]> >To: "'Tandou Mohamed'" ><[EMAIL PROTECTED]>,<[email protected]> >Subject: RE: [OSL | CCIE_RS] IPEXPERT LAB 38 >Date: Wed, 27 Dec 2006 09:08:24 -0500 > >The fact that ports 23 and 24 are trunked between the switches should take >care of all vlan propogation. Once you are trunked in, you can simply add >"interface vlan 10" to the switch. Using "show vlan" or "show >interface trunk" should tell you whether you have proper connectivity, >or knowledge about the other side's vlans. > >Every device has to have an exit point. For a switch, at layer 3 >(participating port) this is normally an SVI (int vlan). > >HTH, > > >Scott Morris, CCIE4 (R&S/ISP-Dial/Security/Service Provider) #4713, >JNCIE #153, CISSP, et al. >CCSI/JNCI-M/JNCI-J >IPExpert VP - Curriculum Development >IPExpert Sr. Technical Instructor >[EMAIL PROTECTED] >http://www.ipexpert.com > > > >-----Original Message----- >From: Tandou Mohamed [mailto:[EMAIL PROTECTED] >Sent: Wednesday, December 27, 2006 7:32 AM >To: [EMAIL PROTECTED]; [email protected] >Subject: RE: [OSL | CCIE_RS] IPEXPERT LAB 38 > > >When i look at the diagram and the instruction provided BB3 is on VLAN >10 with network address 172.16.10.0/24 and CAT1 port 11 is on VLAN 4, >port 1 is on VLAN 111 and port 5 is trunked allowed VLAN 1 and VLAN 6. >so i don't see CAT 1 and BB3 on the same VLAN. >Since port 5 on CAT 1 is trunked it is possible to allowed VLAN 10 to >solve the problem? > >MT > > >From: "Scott Morris" <[EMAIL PROTECTED]> > >Reply-To: <[EMAIL PROTECTED]> > >To: "'Tandou Mohamed'" > ><[EMAIL PROTECTED]>,<[email protected]> > >Subject: RE: [OSL | CCIE_RS] IPEXPERT LAB 38 > >Date: Tue, 26 Dec 2006 21:44:54 -0500 > > > >Ok, so your ethernet interface: > > > >interface Ethernet0/0 > >ip address 172.16.10.103 255.255.255.0 > > > >Is on the same subnet as your bgp peer: > > > >neighbor 172.16.10.10 remote-as 50 > > > >So there really shouldn't be any reason at all to stay in idle. > >Unless, of course, you send a packet out (which would show "active") > >and don't get any response (which will cycle to "idle" for a while). > >So I'd look at your VLAN configuration and see if you have a switch > >problem/L2 problem someplace. > > > >Try pinging it. Should work. > > > >As for your tunnel, that's just using vlan10 as a source for the > >tunnel > >(R4 Lo0 is destination). Different part of the solution for that. > >:) > > > >Check the basics though. Start with a ping since they're on the same > >subnet. > > > >HTH, > > > > > >Scott Morris, CCIE4 (R&S/ISP-Dial/Security/Service Provider) #4713, > >JNCIE #153, CISSP, et al. > >CCSI/JNCI-M/JNCI-J > >IPExpert VP - Curriculum Development > >IPExpert Sr. Technical Instructor > >[EMAIL PROTECTED] > >http://www.ipexpert.com > > > > > > > >-----Original Message----- > >From: Tandou Mohamed [mailto:[EMAIL PROTECTED] > >Sent: Tuesday, December 26, 2006 9:04 PM > >To: [EMAIL PROTECTED]; [email protected] > >Subject: RE: [OSL | CCIE_RS] IPEXPERT LAB 38 > > > > > >Scott, > >here BB3 config and my Cat config > > > >BB3 > > > >interface Loopback100 > >ip address 10.101.100.1 255.255.255.0 ! > >interface Loopback101 > >ip address 10.101.101.1 255.255.255.0 ! > >interface Loopback102 > >ip address 10.101.102.1 255.255.255.0 ! > >interface Loopback103 > >ip address 10.101.103.1 255.255.255.0 ! > >interface Loopback104 > >ip address 10.101.104.1 255.255.255.0 ! > >interface Loopback105 > >ip address 10.101.105.1 255.255.255.0 ! > >interface Loopback106 > >ip address 10.101.106.1 255.255.255.0 ! > >interface Loopback107 > >ip address 10.101.107.1 255.255.255.0 ! > >interface Loopback108 > >ip address 10.101.108.1 255.255.255.0 ! > >interface Loopback109 > >ip address 10.101.109.1 255.255.255.0 ! > >interface Ethernet0/0 > >ip address 172.16.10.103 255.255.255.0 half-duplex ! > >router bgp 101 > >no synchronization > >bgp log-neighbor-changes > >network 10.101.100.0 mask 255.255.255.0 network 10.101.101.0 mask > >255.255.255.0 network 10.101.102.0 mask 255.255.255.0 network > >10.101.103.0 mask 255.255.255.0 network 10.101.104.0 mask > >255.255.255.0 network 10.101.105.0 mask 255.255.255.0 network > >10.101.106.0 mask 255.255.255.0 network 10.101.107.0 mask > >255.255.255.0 network 10.101.108.0 mask 255.255.255.0 network > >10.101.109.0 mask 255.255.255.0 neighbor 172.16.10.10 remote-as 50 no auto-summary ! > >ip http server > >ip classless > >! > >======================================================= > > > >CAT 1 > > > >router bgp 65520 > >no synchronization > >bgp log-neighbor-changes > >bgp confederation identifier 50 > >bgp confederation peers 65522 > >neighbor internal peer-group > >neighbor internal remote-as 65520 > >neighbor internal update-source Loopback0 neighbor 172.16.10.103 > >remote-as 101 neighbor 172.16.10.103 filter-list 10 out neighbor > >192.168.1.1 peer-group internal neighbor 192.168.2.2 peer-group > >internal neighbor 192.168.5.5 peer-group internal neighbor > >192.168.11.11 remote-as 65522 neighbor 192.168.11.11 ebgp-multihop > >255 neighbor 192.168.11.11 update-source Loopback0 no auto-summary > > > >My BGP peering won't establshed. > >I finaly checked the lab solution, i am seeing a tunnel between CAT1 > >and R4 with 172.16.10.0/24. Can you explain why? > > > >Thanks, > > > >MT > > > > >From: "Scott Morris" <[EMAIL PROTECTED]> > > >Reply-To: <[EMAIL PROTECTED]> > > >To: "'Tandou Mohamed'" > > ><[EMAIL PROTECTED]>,<[email protected]> > > >Subject: RE: [OSL | CCIE_RS] IPEXPERT LAB 38 > > >Date: Mon, 25 Dec 2006 00:14:16 -0500 > > > > > >It hard to diagnose what your problem happens to be with a simple > > >"it's not working" message. Idle usally means it's not trying, but > > >it could also depend on WHEN you do the show command as it would > > >cycle between active and idle if no connection takes place. > > > > > >What does the BB3 config look like? In real lab you won't have > > >access, but here you do. So use it to your advantage! > > > > > >Show ip route for starters on each end. > > > > > >Scott > > > > > >-----Original Message----- > > >From: [EMAIL PROTECTED] > > >[mailto:[EMAIL PROTECTED] On Behalf Of Tandou > > >Mohamed > > >Sent: Sunday, December 24, 2006 4:41 PM > > >To: [email protected] > > >Subject: [OSL | CCIE_RS] IPEXPERT LAB 38 > > > > > > > > >Hello Scott, > > >i completed lab 38 i couldn't get the peering between Cat1 and BB3. > > >i checked the answer my config looks the same but BGP is not coming up. > > >can you explain if i am missing something why BGP is not coming and > > >stay > >idle. > > >i > > >tried all kind of peering static route, ebgp multihop etc. > > > > > >Mohamed > > > > > >_________________________________________________________________ > > >Get live scores and news about your team: Add the Live.com Football > > >Page > > >www.live.com/?addtemplate=football&icid=T001MSN30A0701 > > > > > > >_________________________________________________________________ > >Dave vs. Carl: The Insignificant Championship Series. Who will win? > >http://clk.atdmt.com/MSN/go/msnnkwsp0070000001msn/direct/01/?href=http: > >//dav > >evscarl.spaces.live.com/?icid=T001MSN38C07001 > > > >_________________________________________________________________ >Type your favorite song. Get a customized station. Try MSN Radio >powered by Pandora. http://radio.msn.com/?icid=T002MSN03A07001 > _________________________________________________________________ Find sales, coupons, and free shipping, all in one place! MSN Shopping Sales & Deals http://shopping.msn.com/content/shp/?ctid=198,ptnrid=176,ptnrdata=200639
