Do a show frame-relay map... Do any maps come up as dynamic or going to 0.0.0.0? If so, you know what to do :)
Cheers, Matt On 17/02/2008, [EMAIL PROTECTED] <[EMAIL PROTECTED]> wrote: > > > > I have just executed Debug IP Packet, and in fact seem like that knows the > interface to use, however the message Encapsulation failed revealed no > information L2-L3, I thought to reach directly connected although without > static mapping. In the meantime I thank you everyone for support. > ----- Original message ----- > From: "Scott Morris" <[EMAIL PROTECTED]> > To: [EMAIL PROTECTED], [email protected] > Date: Sat, 16 Feb 2008 20:04:09 -0500 > Subject: RE: [OSL | CCIE_RS] Frame-Relay > > > Try looking at the output of "debug ip packet" as you do the various pings! > That may help highlight the missing piece there from pinging yourself > versus the other devices! > > HTH, > > > > > > Scott Morris, CCIE4 (R&S/ISP-Dial/Security/Service Provider) #4713, JNCIE-M > #153, JNCIS-ER, CISSP, et al. > CCSI/JNCI-M/JNCI-ER > VP - Technical Training - IPexpert, Inc. > IPexpert Sr. Technical Instructor > > A Cisco Learning Partner - We Accept Learning Credits! > > [EMAIL PROTECTED] > > > > Telephone: +1.810.326.1444 > Fax: +1.810.454.0130 > http://www.ipexpert.com > > > > ________________________________ > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] On Behalf Of > [EMAIL PROTECTED] > Sent: Saturday, February 16, 2008 12:17 PM > To: [email protected] > Subject: [OSL | CCIE_RS] Frame-Relay > > > I`ve just configured Frame-Relay Hub and Spoke, plus point-to-point. > with point-to-point no problem, with Hub and spoke I pinged only the spokes > but not myself,same thing for both spokes, not reachability for myself. > Can someone help me? > Straight forward the config for Hub: > > interface Serial0/1/0 > no ip address > encapsulation frame-relay > ! > interface Serial0/1/0.100 multipoint > ip address 150.50.100.2 255.255.255.224 > frame-relay map ip 150.50.100.5 205 broadcast > frame-relay map ip 150.50.100.6 206 broadcast > ! > interface Serial0/1/0.104 point-to-point > ip address 150.50.24.2 255.255.255.0 > frame-relay interface-dlci 104 > ! > interface Serial0/2/0 > description Link to R5 > ip address 150.50.9.2 255.255.255.192 > clock rate 2000000 > ! > interface FastEthernet1/0 > description Link to Switch1 > no switchport > ip address 150.50.17.2 255.255.255.0 > > > > Spoke: > interface Loopback0 > ip address 200.0.0.5 255.255.255.255 > ! > interface FastEthernet0/0 > description Link to Switch1 > ip address 150.50.7.5 255.255.255.128 > duplex auto > speed auto > ! > interface FastEthernet0/1 > no ip address > shutdown > duplex auto > speed auto > ! > interface Serial0/1/0 > ip address 150.50.100.5 255.255.255.224 > encapsulation frame-relay > frame-relay map ip 150.50.100.2 502 broadcast > frame-relay map ip 150.50.100.6 506 broadcast > ! > interface Serial0/2/0 > description Link to R2 > ip address 150.50.9.5 255.255.255.192 > -- > This message is intended for the individual(s) to whom it is addressed and > may contain information that is privileged or confidential. > If you are not the addressee you must not read,use or disclose the contents > of this email. > Whilst all reasonable care has been taken to avoid the transmission of > viruses, the recipient should carry out virus and other checks, > as they consider appropriate. > Myself accepts no responsibility in this regard. > > > -- > This message is intended for the individual(s) to whom it is addressed and > may contain information that is privileged or confidential. > If you are not the addressee you must not read,use or disclose the contents > of this email. > Whilst all reasonable care has been taken to avoid the transmission of > viruses, the recipient should carry out virus and other checks, > as they consider appropriate. > Myself accepts no responsibility in this regard. > > >
