Team
I am having some issues with vol1 lab 6 - task 6.16. I checked my printed
copy of the DSG, downloaded the latest electronic copy of the DSG, and
watched the volume 1 walkthrough video and they are all using different
commands.
I downloaded the electronic copy of the vol1 lab 6 - task 6.16 DSG today and
it has the commands listed as below.
R2
_ _ _ _
int s0/1/0.1
frame-relay class FREEK
int s0/0/0
frame-relay interface-dlci 402
class FREEK
R4
_ _ _ _
(Nothing listed here)
I watched the vol1 lab 6 - task 6.16 configuration video and here are the
commands Joe uses there.
R2
_ _ _ _
int s0/1/0.1
frame-relay interface-dlci 204
class FREEK
R4
_ _ _ _
int s0/0/0
frame-relay interface-dlci 402
class FREEK
I also checked my printed copy of the vol1 lab 6 - task 6.16 DSG and below
are the commands it shows.
R2
_ _ _ _
int s0/1/0.1
frame-relay class FREEK
R4
_ _ _ _
int s0/0/0
frame-relay interface-dlci 402
class FREEK
I used the commands listed above from my printed copy of the DSG and I am
showing EEK up on both sides. R4 looks fine but I have some failures on R2.
I also tried this with the other command sets and I still have the same
issue.
R2#sh frame end keep
End-to-end Keepalive Statistics for Interface Serial0/1/0 (Frame Relay DTE)
DLCI = 204, DLCI USAGE = LOCAL, VC STATUS = ACTIVE (EEK UP)
SEND SIDE STATISTICS
Send Sequence Number: 59, Receive Sequence Number: 60
Configured Event Window: 3, Configured Error Threshold: 2
Total Observed Events: 64, Total Observed Errors: 2
Monitored Events: 3, Monitored Errors: 0
Successive Successes: 3, End-to-end VC Status: UP
RECEIVE SIDE STATISTICS
Send Sequence Number: 60, Receive Sequence Number: 59
Configured Event Window: 3, Configured Error Threshold: 2
Total Observed Events: 62, Total Observed Errors: 0
Monitored Events: 3, Monitored Errors: 0
Successive Successes: 3, End-to-end VC Status: UP
Failures Since Started: 1, Last Failure: 00:10:09
R4#sh frame end keep
End-to-end Keepalive Statistics for Interface Serial0/0/0 (Frame Relay DTE)
DLCI = 402, DLCI USAGE = LOCAL, VC STATUS = ACTIVE (EEK UP)
SEND SIDE STATISTICS
Send Sequence Number: 67, Receive Sequence Number: 68
Configured Event Window: 3, Configured Error Threshold: 2
Total Observed Events: 70, Total Observed Errors: 0
Monitored Events: 3, Monitored Errors: 0
Successive Successes: 3, End-to-end VC Status: UP
RECEIVE SIDE STATISTICS
Send Sequence Number: 67, Receive Sequence Number: 66
Configured Event Window: 3, Configured Error Threshold: 2
Total Observed Events: 69, Total Observed Errors: 0
Monitored Events: 3, Monitored Errors: 0
Successive Successes: 3, End-to-end VC Status: UP
Below are my show run results for the two interfaces in question.
R2
interface Serial0/1/0.1 point-to-point
ip address 150.100.24.2 255.255.255.0
frame-relay class FREEK
frame-relay interface-dlci 204 IETF
R4
interface Serial0/0/0
ip address 150.100.24.4 255.255.255.0
encapsulation frame-relay IETF
frame-relay interface-dlci 402
class FREEK
frame-relay interface-dlci 412 ppp Virtual-Template1
Below are what the final configurations show for the interfaces.
R2
interface Serial0/1/0.1 point-to-point
ip address 150.100.24.2 255.255.255.0
frame-relay interface-dlci 204
class FREEK
R4
interface Serial0/0/0
ip address 150.100.24.4 255.255.255.0
encapsulation frame-relay
frame-relay interface-dlci 402
class FREEK
frame-relay interface-dlci 412 ppp Virtual-Template1
The one thing I see that is different between the two is the IETF
encapsulation. I am not sure why the final configurations do not show this
since it is covered in the previous tasks in the lab?
My questions are:
Why am I getting failures on R2?
Which command set should I use printed DSG, electronic DSG or video?
Thank you for the help!
PS: I searched the forums and found this email where Joe responds to another
user that is having issues with this task.
Joe Astorino
Sat, 30 Jan 2010 23:07:07 -0800
Yes. Good catch. It is correct in the final configurations FYI. If
you do NOT apply these per DLCI what will happen is you will have
FR-EEK Failed errors on your console because it will try to send out
the EEK on every DLCI.
On Sun, Jan 31, 2010 at 1:48 AM, L. Jankok <[email protected]> wrote:
> Just noticed a small cosmetic thing here.
>
> On the DSG Volume 1 Lab 6 page 184
>
> On the middle of the page it says
>
> --> So let's change things.
>
> R2
>
> int s0/1/0.1
> frame-relay class FREEK
> int s0/0/0
> frame-relay interface-dlci 402
> class FREEK
>
> R4
>
> --> shouldn't it be something like
>
> R2
>
> int s0/1/0.1
> frame-relay class FREEK
>
> R4
>
> int s0/0/0
> frame-relay interface-dlci 402
> class FREEK
>
> Cheers
> _______________________________________________
> For more information regarding industry leading CCIE Lab training, please
> visit www.ipexpert.com
>
--
Regards,
Joe Astorino CCIE #24347 (R&S)
Sr. Technical Instructor - IPexpert
Mailto: [email protected]
Telephone: +1.810.326.1444
Live Assistance, Please visit: www.ipexpert.com/chat
eFax: +1.810.454.0130
IPexpert is a premier provider of Classroom and Self-Study Cisco CCNA
(R&S, Voice & Security), CCNP, CCVP, CCSP and CCIE (R&S, Voice,
Security & Service Provider) Certification Training with locations
throughout the United States, Europe and Australia. Be sure to check
out our online communities at www.ipexpert.com/communities and our
public website at www.ipexpert.com
_______________________________________________
For more information regarding industry leading CCIE Lab training, please
visit
www.ipexpert.com
_______________________________________________
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
