It worked Steve, I had to remove the config and put it back for some reason.
when i first did debug it was saying unable to add inside translation :S Probably i was missing somthing. i just removed the whole nat config and put it back... it worked. On Sat, Oct 23, 2010 at 1:55 AM, Di Bias, Steve <[email protected]>wrote: > > > Run a “debug ip nat” on R8 and try pinging R1 from Cat2 again (here is what > mine looks like which is working) > > > > R8#deb ip nat > > IP NAT debugging is on > > *Mar 5 07:34:50.834: NAT*: s=100.100.200.12->150.100.78.11, d=200.0.0.1 > [10] > > *Mar 5 07:34:50.842: NAT*: s=200.0.0.1, d=150.100.78.11->100.100.200.12 > [10] > > *Mar 5 07:34:50.846: NAT*: s=100.100.200.12->150.100.78.11, d=200.0.0.1 > [11] > > *Mar 5 07:34:50.850: NAT*: s=200.0.0.1, d=150.100.78.11->100.100.200.12 > [11] > > *Mar 5 07:34:50.854: NAT*: s=100.100.200.12->150.100.78.11, d=200.0.0.1 > [12] > > *Mar 5 07:34:50.858: NAT*: s=200.0.0.1, d=150.100.78.11->100.100.200.12 > [12] > > *Mar 5 07:34:50.862: NAT*: s=100.100.200.12->150.100.78.11, d=200.0.0.1 > [13] > > *Mar 5 07:34:50.870: NAT*: s=200.0.0.1, d=150.100.78.11->100.100.200.12 > [13] > > *Mar 5 07:34:50.878: NAT*: s=100.100.200.12->150.100.78.11, d=200.0.0.1 > [14] > > *Mar 5 07:34:50.882: NAT*: s=200.0.0.1, d=150.100.78.11->100.100.200.12 > [14] > > R > > > > Thank you, > > > > Steve Di Bias > > Network Engineer - Information Systems > > *Valley Health System – Las Vegas* > > *Office* - 702- 369-7594 > > *Cell* - 702-241-1801 > > [email protected] > > > > *From:* [email protected] [mailto: > [email protected]] *On Behalf Of *Amer Mustafa > *Sent:* Friday, October 22, 2010 3:19 PM > *To:* [email protected] > *Subject:* [OSL | CCIE_RS] Workbook 1 - LAB 17 Task 17.2 > > > > *Workbook 1 - LAB 17 Task 17.2* > > > > *Ping to 200.0.0.1 on CAT2 is not working. NAT is working on R8 for some > reason, anyone can tell why * > > > > *Enabling NAT on R8 : * > > > > interface FastEthernet0/0 > ip address 100.100.200.8 255.255.255.0 > ip nat enable > duplex auto > speed auto > end > > > > ! > interface Serial0/0/0 > bandwidth 128 > ip address 150.100.78.8 255.255.255.0 > ip nat enable > no fair-queue > end > > > > ip nat pool AMER 150.100.78.10 150.100.78.254 prefix-length 24 > ip nat inside source list 10 pool AMER > > > > > > R8(config)#do show ip route | i 200.0.0.1 > O 200.0.0.1 [110/1565] via 150.100.78.7, 00:28:30, Serial0/0/0 > > > > > > *FOR NAT VARIFICATION : * > > > > *ON CAT2 : * > > > > Cat3560-2(config)#DO MYIP > Interface IP-Address OK? Method Status > Protocol > Vlan200 100.100.200.12 YES manual up up > > > > > > > Cat3560-2(config)#do ping 100.100.200.8 > > Type escape sequence to abort. > Sending 5, 100-byte ICMP Echos to 100.100.200.8, timeout is 2 seconds: > !!!!! > Success rate is 100 percent (5/5), round-trip min/avg/max = 1/4/9 ms > > > > Cat3560-2(config)#do sh run | beg ip default-gateway > ip default-gateway 100.100.200.8 > > > > *Cat3560-2(config)#do ping 200.0.0.1* > > *Type escape sequence to abort.** > Sending 5, 100-byte ICMP Echos to 200.0.0.1, timeout is 2 seconds: > ..... > Success rate is 0 percent (0/5)* > > > > UHS Confidentiality Notice: This e-mail message, including any attachments, > is for the sole use of the intended recipient(s) and may contain > confidential and privileged information. Any unauthorized review, use, > disclosure or distribution of this information is prohibited, and may be > punishable by law. If this was sent to you in error, please notify the > sender by reply e-mail and destroy all copies of the original message.
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
