Sweet!
From: Amer Mustafa [mailto:[email protected]]
Sent: Friday, October 22, 2010 4:01 PM
To: Di Bias, Steve
Cc: [email protected]
Subject: Re: [OSL | CCIE_RS] Workbook 1 - LAB 17 Task 17.2
It worked Steve,
I had to remove the config and put it back for some reason.
when i first did debug it was saying unable to add inside translation :S
Probably i was missing somthing. i just removed the whole nat config and put it
back... it worked.
On Sat, Oct 23, 2010 at 1:55 AM, Di Bias, Steve
<[email protected]<mailto:[email protected]>> wrote:
Run a "debug ip nat" on R8 and try pinging R1 from Cat2 again (here is what
mine looks like which is working)
R8#deb ip nat
IP NAT debugging is on
*Mar 5 07:34:50.834: NAT*: s=100.100.200.12->150.100.78.11, d=200.0.0.1 [10]
*Mar 5 07:34:50.842: NAT*: s=200.0.0.1, d=150.100.78.11->100.100.200.12 [10]
*Mar 5 07:34:50.846: NAT*: s=100.100.200.12->150.100.78.11, d=200.0.0.1 [11]
*Mar 5 07:34:50.850: NAT*: s=200.0.0.1, d=150.100.78.11->100.100.200.12 [11]
*Mar 5 07:34:50.854: NAT*: s=100.100.200.12->150.100.78.11, d=200.0.0.1 [12]
*Mar 5 07:34:50.858: NAT*: s=200.0.0.1, d=150.100.78.11->100.100.200.12 [12]
*Mar 5 07:34:50.862: NAT*: s=100.100.200.12->150.100.78.11, d=200.0.0.1 [13]
*Mar 5 07:34:50.870: NAT*: s=200.0.0.1, d=150.100.78.11->100.100.200.12 [13]
*Mar 5 07:34:50.878: NAT*: s=100.100.200.12->150.100.78.11, d=200.0.0.1 [14]
*Mar 5 07:34:50.882: NAT*: s=200.0.0.1, d=150.100.78.11->100.100.200.12 [14]
R
Thank you,
Steve Di Bias
Network Engineer - Information Systems
Valley Health System - Las Vegas
Office - 702- 369-7594
Cell - 702-241-1801
[email protected]<mailto:[email protected]>
From:
[email protected]<mailto:[email protected]>
[mailto:[email protected]<mailto:[email protected]>]
On Behalf Of Amer Mustafa
Sent: Friday, October 22, 2010 3:19 PM
To: [email protected]<mailto:[email protected]>
Subject: [OSL | CCIE_RS] Workbook 1 - LAB 17 Task 17.2
Workbook 1 - LAB 17 Task 17.2
Ping to 200.0.0.1 on CAT2 is not working. NAT is working on R8 for some reason,
anyone can tell why
Enabling NAT on R8 :
interface FastEthernet0/0
ip address 100.100.200.8 255.255.255.0
ip nat enable
duplex auto
speed auto
end
!
interface Serial0/0/0
bandwidth 128
ip address 150.100.78.8 255.255.255.0
ip nat enable
no fair-queue
end
ip nat pool AMER 150.100.78.10 150.100.78.254 prefix-length 24
ip nat inside source list 10 pool AMER
R8(config)#do show ip route | i 200.0.0.1
O 200.0.0.1 [110/1565] via 150.100.78.7, 00:28:30, Serial0/0/0
FOR NAT VARIFICATION :
ON CAT2 :
Cat3560-2(config)#DO MYIP
Interface IP-Address OK? Method Status Protocol
Vlan200 100.100.200.12 YES manual up up
Cat3560-2(config)#do ping 100.100.200.8
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 100.100.200.8, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/4/9 ms
Cat3560-2(config)#do sh run | beg ip default-gateway
ip default-gateway 100.100.200.8
Cat3560-2(config)#do ping 200.0.0.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 200.0.0.1, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
UHS Confidentiality Notice: This e-mail message, including any attachments, is
for the sole use of the intended recipient(s) and may contain confidential and
privileged information. Any unauthorized review, use, disclosure or
distribution of this information is prohibited, and may be punishable by law.
If this was sent to you in error, please notify the sender by reply e-mail and
destroy all copies of the original message.
UHS Confidentiality Notice: This e-mail message, including any attachments, is
for the sole use of the intended recipient (s) and may contain confidential and
privileged information. Any unauthorized review, use, disclosure or
distribution of this information is prohibited. If this was sent to you in
error, please notify the sender by reply e-mail and destroy all copies of the
original message.
_______________________________________________
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
