Hi, Can u shutdown the interface while doing etherchannel config and then enable the fe port. This may be da reason.
B.Reg Hamilan On Nov 27, 2011, at 11:11 PM, Christophe Lemaire <[email protected]> wrote: > Just to let you know I've done that lab again and I wasn't able to reproduce > that issue... But I was on a different pod... > > Regards, > Christophe > > On 22 Nov 2011, at 17:50, marc abel wrote: > >> Very interesting, what did you do to resolve it last time? >> >> On Tue, Nov 22, 2011 at 2:15 AM, Christophe Lemaire >> <[email protected]> wrote: >>> Hi Marc, >>> >>> Hmmm... Weird I had that exact same issue when doing that lab... >>> (excepted in my case Fa0/24 was flapping between trunk and access...) >>> >>> I plan to do that lab again on Thursday, I let you know if it happened >>> again... >>> >>> Christophe >>> >>> >>> On Mon, Nov 21, 2011 at 12:34 AM, marc abel <[email protected]> wrote: >>>> It was Vol 3 lab 9 task 1.2 >>>> >>>> On Sun, Nov 20, 2011 at 5:15 PM, Jay McMickle <[email protected]> >>>> wrote: >>>>> Marc- which task is it? >>>>> >>>>> Regards, >>>>> Jay McMickle- CCNP,CCSP,CCDP >>>>> Sent from my iPhone >>>>> http://mycciepursuit.wordpress.com >>>>> >>>>> >>>>> On Nov 20, 2011, at 2:50 PM, Adam Booth <[email protected]> wrote: >>>>> >>>>>> Hi Marc, >>>>>> >>>>>> Do Fa0/23 and Fa0/24 have the same configurations? For example is one >>>>>> port >>>>>> switch access for instance, with the other able to negotiate a trunk >>>>>> using >>>>>> DTP? >>>>>> >>>>>> Perhaps look at hard setting the interfaces to what you want >>>>>> >>>>>> switchport trunk encapsulation dot1q >>>>>> switchport mode trunk >>>>>> switchport nonegotiate >>>>>> >>>>>> Cheers, >>>>>> Adam >>>>>> >>>>>> On Mon, Nov 21, 2011 at 5:54 AM, marc abel <[email protected]> wrote: >>>>>> >>>>>>> I have two dynamic desirable trunks configured as an ether-channel and >>>>>>> one keeps un-bundling >>>>>>> >>>>>>> Nov 20 19:49:06.347: %EC-5-CANNOT_BUNDLE2: Fa0/23 is not compatible >>>>>>> with Fa0/24 and will be suspended (trunk mode of Fa0/23 is access, >>>>>>> Fa0/24 is trunk) >>>>>>> Nov 20 19:49:07.335: %LINEPROTO-5-UPDOWN: Line protocol on Interface >>>>>>> FastEthernet0/23, changed state to down >>>>>>> >>>>>>> >>>>>>> It then comes back up and everything seems fine for a bit and then it >>>>>>> happens again. Any idea what the issue could be or how to >>>>>>> troubleshoot? Obviously I could configure them as statically trunking >>>>>>> but a lab requirement prevents this. >>>>>>> >>>>>>> Thank you, >>>>>>> >>>>>>> Marc >>>>>>> _______________________________________________ >>>>>>> For more information regarding industry leading CCIE Lab training, >>>>>>> please >>>>>>> visit www.ipexpert.com >>>>>>> >>>>>>> Are you a CCNP or CCIE and looking for a job? Check out >>>>>>> www.PlatinumPlacement.com >>>>>>> >>>>>>> To Unsubscribe from this list please visit the following link and follow >>>>>>> the directions to unsubscribe. >>>>>>> http://onlinestudylist.com/mailman/listinfo/ccie_rs >>>>>>> >>>>>> _______________________________________________ >>>>>> For more information regarding industry leading CCIE Lab training, >>>>>> please visit www.ipexpert.com >>>>>> >>>>>> Are you a CCNP or CCIE and looking for a job? Check out >>>>>> www.PlatinumPlacement.com >>>>>> >>>>>> To Unsubscribe from this list please visit the following link and follow >>>>>> the directions to unsubscribe. >>>>>> http://onlinestudylist.com/mailman/listinfo/ccie_rs >>>>> >>>> _______________________________________________ >>>> For more information regarding industry leading CCIE Lab training, please >>>> visit www.ipexpert.com >>>> >>>> Are you a CCNP or CCIE and looking for a job? Check out >>>> www.PlatinumPlacement.com >>>> >>>> To Unsubscribe from this list please visit the following link and follow >>>> the directions to unsubscribe. >>>> http://onlinestudylist.com/mailman/listinfo/ccie_rs >>>> >>> > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com > > To Unsubscribe from this list please visit the following link and follow the > directions to unsubscribe. http://onlinestudylist.com/mailman/listinfo/ccie_rs _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com To Unsubscribe from this list please visit the following link and follow the directions to unsubscribe. http://onlinestudylist.com/mailman/listinfo/ccie_rs
