Hi Joe , I have used it but I prefered to use XP version , I just suggested that you may like to use linux . I think linux & windows are the same in my trial for GNS , but most important IDLEPC value .
You can get the idlepc value as following: - Run R1 , then get the idlepc value for CPU , I got it at 5% , then copy and past it to all use command " idlepc copy R1 all" - Run BB1 ( 2600) and do the same step above. - run the rest of the devices in delay ( wait a time between each one ) , you will see cpu gets high and then backs to low , this is the time to run the other device. BR Best Regards Waleed Abdulfattah Alsherif IP and Data Network Engineer CCIE RS (Written) / CCNP / CCNA Mob. 002-01019556246 ________________________________ From: Joe Danrich <[email protected]> To: Waleed Alsherif <[email protected]> Cc: Ben Hughes <[email protected]>; "[email protected]" <[email protected]> Sent: Friday, February 24, 2012 10:35 PM Subject: Re: [OSL | CCIE_RS] Dynamips & IPExperts .NET/Labs Waleed Have you used the RedNectar at all? It looks promising and what I would end up doing is using the IPExpects files to create that I need. Ben Thanks for the info on the scheduler command.. I hadn't thought of that.. The reason I went to using Kubuntu is due to feedback from people that stated Linux was the way to go with Dynamips with GNS3 as the front end. Now that I have more under my belt with idlepc idlemax and some other commands, I may hack the set- up from IPExperts to get smaller routers (different hypervisor) used in place of 3725.. Cheers Joe On 2/24/2012 5:21 AM, Waleed Alsherif wrote: Hi Joe , > > >I would prefer to use 3725 and 2600 in the simulation , where router 3725 can >simulate a switch ( when you add NM-16ESW module ) , it is not really a switch >but can support " switchport" commands . > > >I am using windows XP ( Ram 4 GB / CPU AMD 4x ) and by idlepc it gets around >20% of CPU . > > >Also, serial interface works fine but the issue of falling asleep is coming >up occasionally. > >Advice: if you have time to spend in preparing GNS3 that would be good , I >have waited 2 weeks long trying to prepare it . > > >You may also check something called " rednectar GNS3 workbench " someone >prepared a workbench on Ubuntu . > >Best Regards >Waleed Abdulfattah Alsherif >IP and Data Network Engineer >CCIE RS (Written) / CCNP / CCNA >Mob. 002-01019556246 > > > >________________________________ > From: Ben Hughes <[email protected]> >To: Joe Danrich <[email protected]>; "[email protected]" ><[email protected]> >Sent: Friday, February 24, 2012 12:03 PM >Subject: Re: [OSL | CCIE_RS] Dynamips & IPExperts .NET/Labs > >Hi Joe, > >I found that I was able to get a stable lab using 2961 routers in dynamips running 12.4(9)T7. The draw back is that there are certain features that aren't available on older code. The only routers that will run the latest code are the 7200's. I've found them to have the falling asleep issue that you mentioned. I recently spent about 4 days straight trying different IOS versions and idlepc values but still no dice. I'm persevering with dynamips as I'm hopefully near the end of the road but if I had my time again I'd find a way to get hardware. I have wasted countless hours on issues related to Dynamips/lab setup. > >Oh, I found I had to remove the scheduler command from router configs in order to get a stable setup. Before I did that my routers were falling over constantly. > >I haven't had any issues with serial interfaces. > >Hope that helps. > >cheers, >Ben. > > >From: Joe Danrich <[email protected]<mailto:[email protected]>> >Date: Thu, 23 Feb 2012 22:18:42 -0800 >To: <[email protected]<mailto:[email protected]>> >Subject: [OSL | CCIE_RS] Dynamips & IPExperts .NET/Labs > >Hi Guys > >I followed with interest the various conversations of Dynamips. I am >using Dynamips with GNS3 on Kubuntu/Ubuntu 11.10 Linux, with the >IPExperts labs I have some questions on how people are running some of >the labs like VOL1 with GNS3? > >Have you encountered issues with serial interfaces not coming up and >staying up with or without a clockrate applied to the applicable serial >interface? > >Routers falling asleep even though the IdlePC, Idlemax idlepc are >appropriately set and overall CPU usage is approximately 60% with all >devices active? > >What IOS's are people using? AIS or AES? > >cheers > >Joe > >_______________________________________________ >For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com > >Are you a CCNP or CCIE and looking for a job? Check out >www.PlatinumPlacement.com > >http://onlinestudylist.com/mailman/listinfo/ccie_rs > >_______________________________________________ >For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com > >Are you a CCNP or CCIE and looking for a job? Check out >www.PlatinumPlacement.com > >http://onlinestudylist.com/mailman/listinfo/ccie_rs > > > _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs
