hem... hem... Doh! :)
Thanks! :D 2012/12/1 Bob McCouch <[email protected]> > > Internet address is 150.100.220.11/28 > > > network 100.110.220.0 0.0.0.15 area 0 > > Might be something to verify... :-) > > Bob > -- > Sent from my iPhone, please excuse any typos. > > On Dec 1, 2012, at 9:31 AM, Cristiano Guerrieri <[email protected]> wrote: > > > Hi all, > > I' a bit stuck with a simple issue, I guess, but I can't figure out what > > is wrong. > > > > I'm ocnfiguring ospf and lab tells me to use VLAN 567. I have full > > reachability between the switches and I can ping the the other switches > > through the VLAN. However the neighbors are no coming up. I ond't see > even > > the attempt to bring them up. > > > > Below the ping connectivity and the configuration for the OSPF > > > > > > ! > > router ospf 1 > > log-adjacency-changes > > passive-interface default > > no passive-interface Vlan567 > > network 100.100.100.0 0.0.0.255 area 0 > > network 100.100.250.0 0.0.0.255 area 0 > > network 100.110.220.0 0.0.0.15 area 0 > > network 150.100.40.0 0.0.0.255 area 0 > > ! > > > > > > > > Cat3550-1#sh interfaces vlan 567 > > Vlan567 is up, line protocol is up > > Hardware is EtherSVI, address is 0009.7c36.5c00 (bia 0009.7c36.5c00) > > Internet address is 150.100.220.11/28 > > MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, > > reliability 255/255, txload 1/255, rxload 1/255 > > Encapsulation ARPA, loopback not set > > Keepalive not supported > > ARP type: ARPA, ARP Timeout 04:00:00 > > Last input 00:00:02, output 00:01:29, output hang never > > Last clearing of "show interface" counters never > > Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 > > Queueing strategy: fifo > > Output queue: 0/40 (size/max) > > 5 minute input rate 0 bits/sec, 0 packets/sec > > 5 minute output rate 0 bits/sec, 0 packets/sec > > 12 packets input, 1038 bytes, 0 no buffer > > Received 0 broadcasts (0 IP multicasts) > > 0 runts, 0 giants, 0 throttles > > 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored > > 2 packets output, 120 bytes, 0 underruns > > 0 output errors, 0 interface resets > > > > Cat3550-1#ping 150.100.220.12 > > > > Type escape sequence to abort. > > Sending 5, 100-byte ICMP Echos to 150.100.220.12, timeout is 2 seconds: > > .!!!! > > Success rate is 80 percent (4/5), round-trip min/avg/max = 1/2/4 ms > > Cat3550-1#ping 150.100.220.13 > > > > Type escape sequence to abort. > > Sending 5, 100-byte ICMP Echos to 150.100.220.13, timeout is 2 seconds: > > .!!!! > > Success rate is 80 percent (4/5), round-trip min/avg/max = 1/2/4 ms > > Cat3550-1#ping 150.100.220.14 > > > > Type escape sequence to abort. > > Sending 5, 100-byte ICMP Echos to 150.100.220.14, timeout is 2 seconds: > > .!!!! > > Success rate is 80 percent (4/5), round-trip min/avg/max = 1/2/4 ms > > Cat3550-1# > > > > > > Any suggestion? > > > > > > Thanks > > Cristiano > > _______________________________________________ > > For more information regarding industry leading CCIE Lab training, > please visit www.ipexpert.com > > > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com > > > > http://onlinestudylist.com/mailman/listinfo/ccie_rs > _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs
