Hello, Have you tried debugging? debug ip ospf adj and I am pretty much sure you should be able to see the reason.
Regards, Samir Idris. On Sun, Dec 2, 2012 at 1:21 AM, Cristiano Guerrieri <[email protected]>wrote: > Hi all, > I' a bit stuck with a simple issue, I guess, but I can't figure out what > is wrong. > > I'm ocnfiguring ospf and lab tells me to use VLAN 567. I have full > reachability between the switches and I can ping the the other switches > through the VLAN. However the neighbors are no coming up. I ond't see even > the attempt to bring them up. > > Below the ping connectivity and the configuration for the OSPF > > > ! > router ospf 1 > log-adjacency-changes > passive-interface default > no passive-interface Vlan567 > network 100.100.100.0 0.0.0.255 area 0 > network 100.100.250.0 0.0.0.255 area 0 > network 100.110.220.0 0.0.0.15 area 0 > network 150.100.40.0 0.0.0.255 area 0 > ! > > > > Cat3550-1#sh interfaces vlan 567 > Vlan567 is up, line protocol is up > Hardware is EtherSVI, address is 0009.7c36.5c00 (bia 0009.7c36.5c00) > Internet address is 150.100.220.11/28 > MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, > reliability 255/255, txload 1/255, rxload 1/255 > Encapsulation ARPA, loopback not set > Keepalive not supported > ARP type: ARPA, ARP Timeout 04:00:00 > Last input 00:00:02, output 00:01:29, output hang never > Last clearing of "show interface" counters never > Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 > Queueing strategy: fifo > Output queue: 0/40 (size/max) > 5 minute input rate 0 bits/sec, 0 packets/sec > 5 minute output rate 0 bits/sec, 0 packets/sec > 12 packets input, 1038 bytes, 0 no buffer > Received 0 broadcasts (0 IP multicasts) > 0 runts, 0 giants, 0 throttles > 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored > 2 packets output, 120 bytes, 0 underruns > 0 output errors, 0 interface resets > > Cat3550-1#ping 150.100.220.12 > > Type escape sequence to abort. > Sending 5, 100-byte ICMP Echos to 150.100.220.12, timeout is 2 seconds: > .!!!! > Success rate is 80 percent (4/5), round-trip min/avg/max = 1/2/4 ms > Cat3550-1#ping 150.100.220.13 > > Type escape sequence to abort. > Sending 5, 100-byte ICMP Echos to 150.100.220.13, timeout is 2 seconds: > .!!!! > Success rate is 80 percent (4/5), round-trip min/avg/max = 1/2/4 ms > Cat3550-1#ping 150.100.220.14 > > Type escape sequence to abort. > Sending 5, 100-byte ICMP Echos to 150.100.220.14, timeout is 2 seconds: > .!!!! > Success rate is 80 percent (4/5), round-trip min/avg/max = 1/2/4 ms > Cat3550-1# > > > Any suggestion? > > > Thanks > Cristiano > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com <http://www.platinumplacement.com/> > > http://onlinestudylist.com/mailman/listinfo/ccie_rs > -- Samir Idris _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs
