Hi Fulvio, This limit was removed with introduction to HQF (Hierarchical Queueing Framework) This was introduced in with 12.4(20)T. Here is a snippet from http://www.cisco.com/en/US/docs/ios/qos/configuration/guide/qos_frhqf_support.html Policy Map and Interface Bandwidth In HQF, a policy map can reserve up to 100 percent of the interface bandwidth. If you do not assign an explicit bandwidth guarantee to the class-default class, you can assign a maximum of 99 percent of the interface bandwidth to user-defined classes and reserve the other 1percent for the class-default class.
-------------------------------------------------------------------------------- Note If you are migrating to Cisco IOS Release 12.4(20)T and the configured policy map allocates 100 percent of the bandwidth to the user-defined classes, an error message appears in the console after booting the HQF image. The message indicates that the allocated bandwidth exceeds the allowable amount, and the service policy is rejected. In HQF, you must reconfigure the policy to account for the minimum 1 percent bandwidth guaranteed for the class-default. Then you can apply a service policy to the interface. Hope this helps! Regards, Naren ________________________________ From: Fulvio allegretti <[email protected]> To: "[email protected]" <[email protected]> Sent: Wednesday, 10 April 2013 4:26 AM Subject: [OSL | CCIE_RS] CBWFQ Bandwidth Allocation Hi all, I know that the sum of reserved bandwidth on CBWFQ cannot exceed 75 % of the interface bandwidth, and if I try to apply a policy to an interface where I have reserved more than 75% I should get something like this: I/f FastEthernet0/0 class RTP requested bandwidth 9000 (kbps), available only 7500 (kbps) but I just can't make this message come up, for some reason I am able to reserve up to 99M on 100 M interface. I am sure am missing something simple here and just can't see the wood for trees at this time at night. Can you help? Thanks, Fulvio R4#sh policy-map Policy Map VOIP Class RTP priority 99000 (kbps) R4#sh run int fa 0/0 Building configuration... Current configuration : 145 bytes ! interface FastEthernet0/0 ip address 150.100.40.4 255.255.255.0 ip ospf mtu-ignore duplex auto speed auto service-policy output VOIP end R4#sh policy-map int fa 0/0 FastEthernet0/0 Service-policy output: VOIP queue stats for all priority classes: queue limit 64 packets (queue depth/total drops/no-buffer drops) 0/0/0 (pkts output/bytes output) 0/0 Class-map: RTP (match-all) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: protocol rtp Priority: 99000 kbps, burst bytes 2475000, b/w exceed drops: 0 Class-map: class-default (match-any) 77 packets, 6651 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: any queue limit 64 packets (queue depth/total drops/no-buffer drops) 0/0/0 (pkts output/bytes output) 77/7624 R4#sh int fa 0/0 | in BW MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs
