I did check on Cisco site and the linecards supports Jumbo Frames. I also discovered that Jumbo frames can be configured at the interface level on this platform.
If I need to configure this on an interface facing a Nexus 5548, will i be breaking any packet flow that are not jumbo? Any feedback on previous exposure at this level would be greatly appreciated. Thank you, I On Thu, Jul 24, 2014 at 1:31 PM, Israel Ogongo <[email protected]> wrote: > Thank you Christian, > > Please see details below: > > Mod Ports Card Type Model Serial > No. > --- ----- -------------------------------------- ------------------ > ----------- > 1 8 CEF720 8 port 10GE with DFC WS-X6708-10GE > SAL1431PMV0 > 2 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX > SAL1552ZC2Y > 5 5 Supervisor Engine 720 10GE (Active) VS-S720-10G > SAL1434RE4W > > Mod MAC addresses Hw Fw Sw > Status > --- ---------------------------------- ------ ------------ ------------ > ------- > 1 5475.d06e.2098 to 5475.d06e.209f 2.2 12.2(18r)S1 12.2(33)SXH8 Ok > 2 70ca.9b68.b348 to 70ca.9b68.b377 4.2 12.2(18r)S1 12.2(33)SXH8 Ok > 5 c47d.4ffe.1c38 to c47d.4ffe.1c3f 3.4 8.5(4) 12.2(33)SXH8 Ok > > Mod Sub-Module Model Serial Hw > Status > ---- --------------------------- ------------------ ----------- ------- > ------- > 1 Distributed Forwarding Card WS-F6700-DFC3C SAL1431PTEW 1.4 Ok > 2 Centralized Forwarding Card WS-F6700-CFC SAL16010AP0 4.1 Ok > 5 Policy Feature Card 3 VS-F6K-PFC3C SAL1434RMY0 1.2 Ok > 5 MSFC3 Daughterboard VS-F6K-MSFC3 SAL1433QQK5 5.0 Ok > > Mod Online Diag Status > ---- ------------------- > 1 Pass > 2 Pass > 5 Pass > > > > On Thu, Jul 24, 2014 at 12:46 PM, Christian Schroeder < > [email protected]> wrote: > >> Hi Israel, >> >> >> on the 6509 the MTU capabilities depend on the linecard. >> >> Can you tell us which linecards you use? >> The output of a "show module" should give us sufficient information for >> further investigation. >> >> >> Cheers, >> Christian >> >> >> >> On Thu, 24 Jul 2014, Israel Ogongo wrote: >> >> Hi all, >>> >>> I am trying to implement Jumbo Frames for Backup / Data Domain purposes >>> at >>> the Data Center. >>> >>> The configuration is straight forward on the Nexus 5548 based on my >>> different research but my CORE is a 6509 running VSS. >>> >>> Please if anyone has implemented Jumbo Frames in such an environment, >>> would >>> like to hear from you and how it has been implemented without error. I >>> dont >>> have a lab environment to simulate this first hence, looking for anyone >>> with previous hands on... >>> >>> Here is the network setup: >>> >>> 6500A ---- 6500B >>> | | >>> | | >>> Nexus 5kA Nexus 5KB - vPC >>> | | >>> | | >>> Many Nexus 2Ks and the Servers are hanging off here.. >>> >>> The Data Domain hangs off the nexus 5548. >>> >>> The question is, how to enable Jumbo Frames on the 6500s - should it be >>> on >>> the interfaces participating in Port-Channel connecting to Nexus 5Ks? >>> >>> Would greatly appreciate your feedback. >>> >>> thank you, >>> _______________________________________________ >>> Free CCIE R&S, Collaboration, Data Center, Wireless & Security Videos :: >>> >>> iPexpert on YouTube: www.youtube.com/ipexpertinc >>> >>> > _______________________________________________ Free CCIE R&S, Collaboration, Data Center, Wireless & Security Videos :: iPexpert on YouTube: www.youtube.com/ipexpertinc
