Hi Sergio, You r the man, Tanx it solves the problem and works like a charm.
Regards, Jeremy On Tue, Oct 21, 2008 at 7:58 AM, Sergio Polizer <[EMAIL PROTECTED]>wrote: > Jeremy, > > Check if your MC3810 requires "no use-proxy FXSZONE default inbound-to > terminal" under gatekeeper configuration. > > It worked for me with a ATA (h323) for calls *from* CallManager. > > HTH > > Sergio. > > ------------------------------ > > Date: Sat, 18 Oct 2008 14:50:03 +1100 > From: [EMAIL PROTECTED] > To: [EMAIL PROTECTED] > CC: ccie_voice@onlinestudylist.com > > Subject: Re: [OSL | CCIE_Voice] call disconnected after couple of seconds, > cannot hear any thing when picked up. > > > Hi Scott, > > I uncheck that already, > > IPIPGW config : > > Current configuration : 4926 bytes > ! > ! Last configuration change at 19:00:36 AUS Fri Mar 1 2002 > ! NVRAM config last updated at 18:42:19 AUS Fri Mar 1 2002 > ! > version 12.4 > service timestamps debug datetime msec > service timestamps log datetime msec > no service password-encryption > ! > hostname C2600 > ! > boot-start-marker > boot-end-marker > ! > ! > no aaa new-model > memory-size iomem 10 > clock timezone AUS 10 > network-clock-participate slot 1 > no network-clock-participate wic 0 > ip cef > ! > ! > ! > ! > no ip domain lookup > ! > ! > ! > frame-relay switching > isdn switch-type primary-ni > voice-card 1 > dsp services dspfarm > ! > ! > ! > ! > voice service voip > allow-connections h323 to h323 > ! > ! > ! > ! > ! > ! > ! > ! > ! > ! > ! > ! > ! > ! > ! > controller T1 1/0 > framing esf > clock source internal > linecode b8zs > pri-group timeslots 1-10,24 > ! > controller T1 1/1 > framing esf > clock source internal > linecode b8zs > pri-group timeslots 1-10,24 > ! > controller E1 1/2 > ds0-group 0 timeslots 1-2 type r2-digital r2-semi-compelled ani > ! > controller E1 1/3 > ! > ip tftp source-interface Loopback10 > ! > ! > ! > ! > ! > interface Loopback0 > ip address 7.7.7.7 255.255.255.255 > ! > interface Loopback2 > ip address 2.2.2.2 255.255.255.0 > ip route-cache same-interface > h323-gateway voip interface > h323-gateway voip id IPIPGWZONE ipaddr 7.7.7.7 1719 > h323-gateway voip h323-id IPIPGW > ! > interface Loopback10 > no ip address > ! > interface FastEthernet0/0 > no ip address > duplex auto > speed auto > ! > interface FastEthernet0/0.200 > encapsulation dot1Q 200 > ip address 200.0.0.254 255.255.255.0 > ! > interface Serial0/0 > no ip address > shutdown > clock rate 115200 > ! > interface Service-Engine0/0 > no ip address > shutdown > ! > interface Serial0/1 > no ip address > encapsulation frame-relay > clock rate 115200 > frame-relay intf-type dce > frame-relay route 109 interface Serial0/3 901 > ! > interface Serial0/2 > no ip address > encapsulation frame-relay > clock rate 115200 > frame-relay intf-type dce > frame-relay route 209 interface Serial0/3 902 > ! > interface Serial0/3 > no ip address > encapsulation frame-relay > clock rate 115200 > frame-relay intf-type dce > frame-relay route 901 interface Serial0/1 109 > frame-relay route 902 interface Serial0/2 209 > ! > interface Serial1/0:23 > no ip address > encapsulation hdlc > isdn switch-type primary-ni > isdn protocol-emulate network > isdn incoming-voice voice > no cdp enable > ! > interface Serial1/1:23 > no ip address > encapsulation hdlc > isdn switch-type primary-ni > isdn protocol-emulate network > isdn incoming-voice voice > no cdp enable > ! > router ospf 1 > log-adjacency-changes > network 0.0.0.0 255.255.255.255 area 0 > ! > no ip forward-protocol nd > ip route 10.0.0.0 255.255.255.0 FastEthernet0/0 > ! > ! > no ip http server > no ip http secure-server > ! > ! > ! > tftp-server flash:2500.bin > ! > control-plane > ! > ! > ! > voice-port 1/0:23 > ! > voice-port 1/1:23 > ! > voice-port 1/2:0 > ! > ! > mgcp > ! > sccp local FastEthernet0/0.200 > sccp ccm 200.0.0.254 identifier 1 > sccp > ! > sccp ccm group 1 > associate ccm 1 priority 1 > associate profile 1 register XCODER > ! > dspfarm profile 1 transcode > codec g711ulaw > codec g711alaw > codec g729ar8 > codec g729abr8 > codec g729r8 > codec g729br8 > maximum sessions 4 > associate application SCCP > ! > ! > dial-peer voice 5000 pots > destination-pattern 0982133335... > direct-inward-dial > forward-digits 8 > ! > dial-peer voice 4000 pots > destination-pattern 061388884... > direct-inward-dial > forward-digits 4 > ! > dial-peer voice 30 pots > destination-pattern 01144334... - Show quoted text - > > port 1/2:0 > forward-digits 8 > ! > dial-peer voice 200 pots > incoming called-number . > direct-inward-dial > port 1/2:0 > ! > dial-peer voice 600 voip > destination-pattern 2222 > session target ras > dtmf-relay h245-alphanumeric > codec g711ulaw > ! > dial-peer voice 601 voip > destination-pattern 3... > session target ras > dtmf-relay h245-alphanumeric > codec g711ulaw > ! > gateway > timer receive-rtp 1200 > ! > ! > ! > ! > gatekeeper > zone local CCMZONE abc.com 7.7.7.7 > zone local HQZONE abc.com > zone local IPIPGWCCMZONE abc.com > zone local IPIPGWZONE abc.com > zone local FXSZONE abc.com invia IPIPGWZONE outvia IPIPGWZONE > enable-intrazone > no zone subnet CCMZONE default enable > zone subnet CCMZONE 114.0.0.12/32 enable > zone subnet CCMZONE 114.0.0.11/32 enable > zone subnet HQZONE 114.0.0.254/32 enable > no zone subnet HQZONE 200.0.0.100/32 enable > zone subnet IPIPGWCCMZONE 114.0.0.11/32 enable > zone subnet IPIPGWZONE 2.2.2.2/32 enable > zone prefix HQZONE 011* > zone prefix IPIPGWCCMZONE 3... > gw-type-prefix 1#* default-technology > bandwidth interzone zone CCMZONE 144 > no shutdown > ! > ! > telephony-service > max-ephones 10 > max-dn 10 > ip source-address 200.0.0.254 port 2000 > sdspfarm units 1 > sdspfarm transcode sessions 2 > max-conferences 4 gain -6 > ! > ! > line con 0 > exec-timeout 0 0 > privilege level 15 > logging synchronous > login > line 25 > no activation-character > no exec > transport preferred none > transport input all > transport output all > line aux 0 > line vty 0 4 > privilege level 15 > password cisco > login > ! > ntp source FastEthernet0/0.200 > ntp master 1 > ! > end > > > > Thanks, > > Any help will appreciated > > > Jeremy > > On Sat, Oct 18, 2008 at 2:36 PM, Hardesty, Scott <[EMAIL PROTECTED]>wrote: > > > Make sure that you do NOT have "wait for h245 capabilities exchange" > enabled on your CCM trunk. > > Please send full configuration on your Gatekeeper / IPIPGW. > > > > > *Scott Hardesty | Cisco Engineer | MidAtlantic | Presidio Networked > Solutions* > > *7601 Ora Glen Drive, Suite 100, Greenbelt, MD 20770 | > [EMAIL PROTECTED] > > *D: 301.313.2041 | C: 443.789.1219 | www.presidio.com* > > ** > > > > ------------------------------ > > *From:* [EMAIL PROTECTED] [mailto: > [EMAIL PROTECTED] *On Behalf Of *jeremy co > *Sent:* Friday, October 17, 2008 11:26 PM > *To:* ccie_voice@onlinestudylist.com > *Subject:* Re: [OSL | CCIE_Voice] call disconnected after couple of > seconds,cannot hear any thing when picked up. > > > > > > I forgot to say I got "bearer capability not implemented (65)" for > disconnected cause code. > > > On Sat, Oct 18, 2008 at 2:21 PM, jeremy co <[EMAIL PROTECTED]> > wrote: > Hi, > > I add some commands as u guys suggested: > > Interesting things happened. from CCM to MC3810 when I make a call ,it > would ring ( not a full ring ,just hear ringing for 0.5 sec) and then > disconnected. > from MC3810 FXS port to CCM ,I can call and ip phone ringing then when I > pick up the ipphone ,nothing happens and from analogue phone prespective > it seems no body picks up the ip phone on other side and keep hearing dial > tone wait for other side to pick up , after couple of seconds I hear fast > busy signal and both ends disconnected. > > So wired!!!!! ANy idea what's going on!!!? > > By the way I use 711 on ccm and 711 ulaw hardcoded to dial peer on > IPIPGW/GK as u can see. > > Here are some changes I made AS U GUYS SUGGESTED: > > > --- unchecked wait for media capabilities > > on MC3810: > > dial-peer voice 300 voip > > destination-pattern 3... > session target ras > dtmf-relay h245-alphanumeric ///this command added > > on IPIPGW/GK: > > telephony-service > max-ephones 10 > max-dn 10 > sdspfarm units 1 > sdspfarm transcode sessions 2 > > > > Cheers, > > > > > On Sat, Oct 18, 2008 at 6:3 AM, James Key <[EMAIL PROTECTED]> wrote: > Jeremy, > On your Gatekeeper controlled trunk, make sure that "Wait for Far End H.245 > Terminal Capabilities Set" is NOT checked. When an IPIPGW is involved, > everything has to be hardcoded and H.245 negotiation doesn't place nice with > IPIPGW in 12.4 mainline IOS. > > > James > > > *From:* [EMAIL PROTECTED] [mailto: > [EMAIL PROTECTED] *On Behalf Of *jeremy co > *Sent:* Friday, October 17, 2008 11:16 AM > > *To:* ccie_voice@onlinestudylist.com > *Subject:* [OSL | CCIE_Voice] call disconnected after couple of > seconds,cannot hear any thing when picked up. > > Hi, > > > (3001) ipphone------CCM------HQ---IPIPGW/GK-----MC3810--FXS (2222) > > > CCM in IPIPGWCCMZONE zone > HQ in HQZONE > IPIPGW/GK in IPIPGWZONE > MC3810 in FXSZONE > > > I get no resource (47) disconnected cause code . > > When I remove " zone local FXSZONE abc.com invia IPIPGWZONE outvia > IPIPGWZONE enable-intrazone" from GK and replace it with " zone local > FXSZONE abc.com" > , basically removing ipipgw , every thing is fine and I can call from both > sides ,ccm and FXS port, but as soon as I add "invia IPIPGWZONE outvia > IPIPGWZONE enable-intrazone", > I can still call fraom both sides but when i pick up the phone I cannot > hear any thing and call will disconnected in couple of seconds. even if I > let phones ringing after couple of seconds it will disconnect. > > It sunds like codec problem but I believe some thing is wrong with ipipgw > config. > > Any idea? > > this is my scenario: > > > PIPGW/GK config : > > hostname C2600 > ! > frame-relay switching > isdn switch-type primary-ni > voice-card 1 > dsp services dspfarm > ! > ! > ! > ! > voice service voip > allow-connections h323 to h323 > ! > ! > ! > ! > ! > controller T1 1/0 > framing esf > clock source internal > linecode b8zs > pri-group timeslots 1-10,24 > ! > controller T1 1/1 > framing esf > clock source internal > linecode b8zs > pri-group timeslots 1-10,24 > ! > controller E1 1/2 > ds0-group 0 timeslots 1-2 type r2-digital r2-semi-compelled ani > ! > ! > interface Loopback0 > ip address 7.7.7.7 255.255.255.255 > ! > interface Loopback2 > ip address 2.2.2.2 255.255.255.0 > ip route-cache same-interface > h323-gateway voip interface > h323-gateway voip id IPIPGWZONE ipaddr 7.7.7.7 1719 > h323-gateway voip h323-id IPIPGW > > ! > interface FastEthernet0/0.200 > encapsulation dot1Q 200 > ip address 200.0.0.254 255.255.255.0 > ! > ! > mgcp > ! > sccp local FastEthernet0/0.200 > sccp ccm 142.4.64.11 identifier 1 > sccp > ! > sccp ccm group 1 > associate ccm 1 priority 1 > associate profile 1 register XCODER > ! > dspfarm profile 1 transcode > codec g711ulaw > codec g711alaw > codec g729ar8 > codec g729abr8 > codec g729r8 > codec g729br8 > maximum sessions 4 > associate application SCCP > ! > ! > dial-peer voice 30 pots > destination-pattern 01122443... > port 1/2:0 > forward-digits 8 > ! > dial-peer voice 200 pots > incoming called-number . > direct-inward-dial > port 1/2:0 > ! > dial-peer voice 600 voip > destination-pattern 2222 > session target ras > dtmf-relay h245-alphanumeric > codec g711ulaw > ! > dial-peer voice 601 voip > destination-pattern 3... > session target ras > dtmf-relay h245-alphanumeric > codec g711ulaw > ! > gateway > timer receive-rtp 1200 > ! > ! > ! > ! > gatekeeper > zone local CCMZONE abc.com 7.7.7.7 > zone local HQZONE abc.com > zone local IPIPGWCCMZONE abc.com > zone local IPIPGWZONE abc.com > zone local FXSZONE abc.com invia IPIPGWZONE outvia IPIPGWZONE > enable-intrazone > no zone subnet CCMZONE default enable > zone subnet CCMZONE 114.0.0.11/32 enable > zone subnet CCMZONE 114.0.0.12/32 enable > no zone subnet HQZONE 200.0.0.100/32 enable > zone subnet HQZONE 114.0.0.254/32 enable > zone subnet IPIPGWCCMZONE 114.0.0.11/32 enable > zone subnet IPIPGWZONE 2.2.2.2/32 enable > zone prefix HQZONE 011* > zone prefix IPIPGWCCMZONE 3... > gw-type-prefix 1#* default-technology > bandwidth interzone zone CCMZONE 144 > no shutdown > ! > ! > > > HQ config : > > interface FastEthernet0/0.11 > encapsulation dot1Q 11 > ip address 114.0.0.254 255.255.255.0 > no snmp trap link-status > h323-gateway voip interface > h323-gateway voip id HQZONE ipaddr 7.7.7.7 1719 > h323-gateway voip h323-id [EMAIL PROTECTED] > h323-gateway voip tech-prefix 3# > ! > gateway > > ########MC3810 config :#################### > > interface Ethernet0 > ip address 200.0.0.100 255.255.255.0 > h323-gateway voip interface > h323-gateway voip id FXSZONE ipaddr 7.7.7.7 1718 > h323-gateway voip h323-id MC3810 > h323-gateway voip bind srcaddr 200.0.0.100 > ! > gateway > > > regards, > > Jeremy > > > > NOTICE: This electronic mail message and any files transmitted with it are > intended > > exclusively for the individual or entity to which it is addressed. The > message, > > together with any attachment, may contain confidential and/or privileged > information. > > Any unauthorized review, use, printing, saving, copying, disclosure or > distribution > > is strictly prohibited. If you have received this message in error, please > > immediately advise the sender by reply email and delete all copies. > > > > > > > ------------------------------ > Veja mapas e encontre as melhores rotas para fugir do trânsito com o Live > Search Maps! Experimente já!<http://www.livemaps.com.br/index.aspx?tr=true> >