Hi Mark, non of these solved my problem, something very wired is happening in my lab!!!
I'm using unity and ccm on two different vmware machines. with default port of 2000 ,integration would fail. (I didn't change any default ports on ccm). When I change default port to 2001 or 2002 on unity integration wizard , what I get is I can verify ports on unity but not on ccm. As a workaround I change ethernet port on both ccm and unity to 4000 and then they integrate together successfully. I don't have any firewall in the way.I still donnow why this happened, Regards Jeremy On Fri, Oct 31, 2008 at 1:46 AM, Mark Snow <[EMAIL PROTECTED]> wrote: > Try deleting the VM ports from UCM and putting them back in - just so that > everything in the process is re-done. > Also - check to see if Phones show up as registered or not found. (not if > they work or not - just what does UCM phone page say - reg or not found). > If phones show as not found - check your RIS Data Collector service to make > sure it is started. > But I don't really think that is the issue here. > > After you have put your VM ports back in (with LG,HL, and HP), then restart > Both CCM processes. > > Cheers, > > -- > Mark Snow > CCIE #14073 (Voice, Security) > > Senior Technical Instructor - IPexpert, Inc. > > Telephone: +1.810.326.1444 > Fax: +1.309.413.4097 > Mailto: [EMAIL PROTECTED] > -- > Join our free online support and peer group communities: > http://www.IPexpert.com/communities > -- > IPexpert - The Global Leader in Self-Study, Classroom-Based, > Video-On-Demand and Audio Certification Training Tools for the Cisco CCIE > R&S Lab, CCIE Security Lab, CCIE Service Provider Lab , CCIE Voice Lab and > CCIE Storage Lab Certifications. > -- > > On Oct 29, 2008, at 3:06 PM, jeremy co wrote: > > > Well, I can verify it on unity, and it passes all of 4 ports successfully. > (btw, I can make it work only when I change port of ccm on unity integration > wizard to 2002 !!!) ,I donnow yet why by 2000 it was not integrate to ccm. I > didn't change any default ports on ccm . > > on ccm after resetting ports, I still see "Not found" > > > Jeremy > > On Thu, Oct 30, 2008 at 5:52 AM, Chris Parker <[EMAIL PROTECTED]> wrote: > >> It sounds like unity is not registering its ports with the callmanager. On >> the Unity server, go into the Telephony Integration under system tools and >> test your integration. If that fails make sure the port names in unity match >> what you have set on callmanager. Try restarting Unity too. >> >> >> jeremy co wrote: >> >>> Hi, >>> >>> Jacob I did the firs two. but I'm not sure what u mean by registering vm >>> ports. >>> >>> on unity I can verify ,call manager integration, and on ccm on "voice >>> mail ports",I can see "not found" status. >>> >>> When I hit message button, I hear fast busy tone. >>> >>> When I dial pilot number ,also hear fast busy signal. I think CCM not >>> forward call to unity >>> >>> btw, every thing is in none partition, no CSS. >>> >>> >>> >>> Jeremy >>> >>> >>> On Thu, Oct 30, 2008 at 5:12 AM, Chris Parker <[EMAIL PROTECTED]<mailto: >>> [EMAIL PROTECTED]>> wrote: >>> >>> What happens when you dial you voicemail pilot? Does the call ring >>> through? Are phones able to access voicemail via the messages key? >>> >>> If the answers to the above are yes, then I would look at possible >>> codec or CAC problems. For example is the call rinnging into the >>> phone 729, then trying to go 711 when it goes to Unity? If so you >>> may need to check your transcoder. >>> >>> >>> jeremy co wrote: >>> >>> Hi, >>> >>> >>> I integrate CCM to unity and define 4 ports on both unity and >>> ccm.Then, check DN's options on Phones to forward unanswered >>> calls to voice mail. Subscribers are created with extention of >>> 3001 and 3007 and set active schedule to "all houres- alldays" >>> >>> I have 2 IPphones with DN's of 3001 and 3007. >>> >>> When I call another ip phone and one does not answer the call, >>> I hear fast busy tone and nothing is forwarded to voice mail. >>> >>> Am I miss anything? >>> >>> Jeremy >>> >>> >>> >>> >> > >
