Just erased the config, re configured it with same result. I have also tried (and currently using) non-GK controlled ICT to take GK out of the mix (just incase). Calls go through fine with g711 forced end to end, but with 729 to CME they fail. Attached is the config as it stands right now.
________________________________ From: Vik Malhi [mailto:vma...@ipexpert.com] Sent: Monday, February 23, 2009 12:22 PM To: Kevin Hogan (kevhogan); OSL Group Subject: Re: [OSL | CCIE_Voice] CCM-->CUE call fail Check the output of "show sdspfarm units" on the CME- how does it look? Also can you send your full CME router config. -- Vik Malhi - CCIE #13890, CCSI #31584 Senior Technical Instructor - IPexpert, Inc. Telephone: +1.810.326.1444 Fax: +1.810.454.0130 Mailto: vma...@ipexpert.com Join our free online support and peer group communities: http://www.IPexpert.com/communities IPexpert - The Global Leader in Self-Study, Classroom-Based, Video-On-Demand and Audio Certification Training Tools for the Cisco CCIE R&S Lab, CCIE Security Lab, CCIE Service Provider Lab , CCIE Voice Lab and CCIE Storage Lab Certifications. ________________________________ From: "Kevin Hogan (kevhogan)" <kevho...@cisco.com> Date: Mon, 23 Feb 2009 12:28:11 -0500 To: Vik Malhi <vma...@ipexpert.com>, OSL Group < ccie_voice@onlinestudylist.com> Subject: RE: [OSL | CCIE_Voice] CCM-->CUE call fail Can ping the 6608 Xcoder IP from the CUE and other way. G711 works fine. Hmmmm. ________________________________ From: Vik Malhi [mailto:vma...@ipexpert.com] Sent: Monday, February 23, 2009 11:21 AM To: Kevin Hogan (kevhogan); OSL Group Subject: Re: [OSL | CCIE_Voice] CCM-->CUE call fail Sounds like a routing issue somewhere along the media path. - Check the default gw for the CUE. - If the call is passing through an MTP on the CCM side check the xcoder default gw (6608). A problem here would also cause dead air on calls to CME phones - if the two things above are fine then remove the need for the xcoder. Change the DP on the trunk, change your incoming dial-peer codec, remove any bandwidth CAC on the GK and test g711u end to end. -- Vik Malhi - CCIE #13890, CCSI #31584 Senior Technical Instructor - IPexpert, Inc. Telephone: +1.810.326.1444 Fax: +1.810.454.0130 Mailto: vma...@ipexpert.com Join our free online support and peer group communities: http://www.IPexpert.com/communities IPexpert - The Global Leader in Self-Study, Classroom-Based, Video-On-Demand and Audio Certification Training Tools for the Cisco CCIE R&S Lab, CCIE Security Lab, CCIE Service Provider Lab , CCIE Voice Lab and CCIE Storage Lab Certifications. ________________________________ From: "Kevin Hogan (kevhogan)" <kevho...@cisco.com> Date: Mon, 23 Feb 2009 11:42:47 -0500 To: Vik Malhi <vma...@ipexpert.com>, OSL Group < ccie_voice@onlinestudylist.com> Subject: RE: [OSL | CCIE_Voice] CCM-->CUE call fail Already have it in there (forgot to put that in last email) and the call is hitting it. Still dead air when CUE answers. Here is the incoming DP it is hitting: dial-peer voice 1001 voip translation-profile incoming strip-prefix ---strips tech prefix. incoming called-number 2#3... ---tried with "." just incase, but no luck no vad ________________________________ From: Vik Malhi [mailto:vma...@ipexpert.com] Sent: Monday, February 23, 2009 9:10 AM To: Kevin Hogan (kevhogan); OSL Group Subject: Re: [OSL | CCIE_Voice] CCM-->CUE call fail I think you need an inbound VOIP dial-peer in order to fix the codec to g729 and thereby intiating the transcoder. Try this: Dial-p v xx voip incoming called-number . codec g729r8 !! DEFAULT COMMAND- FYI only -- Vik Malhi - CCIE #13890, CCSI #31584 Senior Technical Instructor - IPexpert, Inc. Telephone: +1.810.326.1444 Fax: +1.810.454.0130 Mailto: vma...@ipexpert.com Join our free online support and peer group communities: http://www.IPexpert.com/communities IPexpert - The Global Leader in Self-Study, Classroom-Based, Video-On-Demand and Audio Certification Training Tools for the Cisco CCIE R&S Lab, CCIE Security Lab, CCIE Service Provider Lab , CCIE Voice Lab and CCIE Storage Lab Certifications. ________________________________ From: "Kevin Hogan (kevhogan)" <kevho...@cisco.com> Date: Mon, 23 Feb 2009 02:54:27 -0500 To: OSL Group <ccie_voice@onlinestudylist.com> Subject: [OSL | CCIE_Voice] CCM-->CUE call fail Have CCM---> GK Controlled ICT (G.729) -- > CME --> CFNA (or direct to VM) -->CUE. With IOS 12.4(3) call gets to CUE, but no audio. With IOS 12.4(23) call gets fast busy (tried changing IOS incase DSP firmware issue or bug). I have xcoders on CME...here is the output of show sccp: SCCP Admin State: UP Gateway IP Address: 192.168.1.1 Switchover Method: IMMEDIATE, Switchback Method: GUARD_TIMER Switchback Guard Timer: 1200 sec, IP Precedence: 5 Max Supported MTP sessions: 0 User Masked Codec list: None Transcoding Oper State: ACTIVE - Cause Code: NONE Active Call Manager: 10.1.202.1, Port Number: 2000 TCP Link Status: CONNECTED Conferencing Oper State: DOWN - Cause Code: DSPFARM_DOWN Active Call Manager: NONE TCP Link Status: NOT_CONNECTED Call Manager: 10.1.202.1, Port Number: 2000 Priority: 1, Version: 3.1 or Higher The "Max Supported MTP sessions: 0" seems strange to me. Not sure if that is normal or not. If I use g.711 throughout the call goes through fine. Relevant pieces of CME config: voice-card 2 dspfarm dsp services dspfarm ! voice service voip allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip ! sccp local FastEthernet0/1 sccp sccp ccm 10.1.202.1 priority 1 ! dspfarm transcoder maximum sessions 10 dspfarm ! dial-peer voice 3600 voip destination-pattern 3[1269].. session protocol sipv2 session target ipv4:10.1.202.2 dtmf-relay sip-notify codec g711ulaw no vad ! telephony-service sdspfarm units 1 sdspfarm transcode sessions 10 sdspfarm tag 1 mtp001ae2a4c081 call-forward pattern .T transfer-system full-consult transfer-pattern .T Any ideas??? Thanks!
BR2#show run Building configuration... Current configuration : 4367 bytes ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname BR2 ! boot-start-marker boot-end-marker ! no logging console enable password cisco ! no aaa new-model ! resource policy ! network-clock-participate slot 1 no network-clock-participate slot 2 voice-card 1 dspfarm ! voice-card 2 dspfarm dsp services dspfarm ! ip subnet-zero ip cef ! ! ! ! isdn switch-type primary-net5 ! ! ! voice service voip allow-connections h323 to sip allow-connections sip to h323 ! ! ! ! ! ! ! ! ! ! voice translation-rule 1 rule 1 /^331321\(3...\)/ /\1/ ! voice translation-rule 2 rule 1 // /\0/ type any unknown plan any unknown ! voice translation-rule 3 rule 1 /3.../ /331321\0/ ! ! voice translation-profile inbound translate called 1 ! voice translation-profile outbound translate calling 3 translate called 2 ! ! ! ! controller E1 1/0 pri-group timeslots 1-3,16 ! controller E1 1/1 ! ! ! interface Loopback0 ip address 172.1.102.1 255.255.255.0 h323-gateway voip interface h323-gateway voip id CCM ipaddr 172.1.100.1 1719 h323-gateway voip h323-id BR2 h323-gateway voip tech-prefix 2# h323-gateway voip bind srcaddr 172.1.102.1 ! interface FastEthernet0/0 no ip address duplex auto speed auto ! interface FastEthernet0/0.110 encapsulation dot1Q 110 ip address 10.1.102.1 255.255.255.0 no snmp trap link-status ! interface FastEthernet0/0.210 encapsulation dot1Q 210 ip address 10.1.202.1 255.255.255.0 ip helper-address 10.1.200.21 no snmp trap link-status ! interface Serial0/0 no ip address encapsulation frame-relay IETF frame-relay lmi-type ansi ! interface Serial0/0.202 point-to-point description BR2-Frame-Connection ip address 162.1.102.2 255.255.255.0 frame-relay interface-dlci 202 ! interface Service-Engine0/0 ip unnumbered FastEthernet0/0.210 service-module ip address 10.1.202.2 255.255.255.0 service-module ip default-gateway 10.1.202.1 ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial0/1 no ip address shutdown clock rate 2000000 ! interface Serial1/0:15 no ip address isdn switch-type primary-net5 isdn incoming-voice voice isdn outgoing display-ie no cdp enable ! ip classless ip route 10.1.100.0 255.255.255.0 162.1.102.1 ip route 10.1.101.0 255.255.255.0 162.1.102.1 ip route 10.1.200.0 255.255.255.0 162.1.102.1 ip route 10.1.201.0 255.255.255.0 162.1.102.1 ip route 10.1.202.2 255.255.255.255 Service-Engine0/0 ip route 100.100.100.0 255.255.255.0 10.1.102.253 ip route 172.1.100.0 255.255.255.0 162.1.102.1 ip route 172.1.101.0 255.255.255.0 162.1.102.1 ! ip http server ! ! ! ! control-plane ! ! ! voice-port 1/0:15 translation-profile incoming inbound translation-profile outgoing outbound ! ! ! sccp local FastEthernet0/0.210 sccp sccp ccm 10.1.202.1 priority 1 ! dspfarm transcoder maximum sessions 10 dspfarm ! ! dial-peer voice 9 pots destination-pattern 9T port 1/0:15 ! dial-peer voice 3600 voip destination-pattern 3[1269].. session protocol sipv2 session target ipv4:10.1.202.2 incoming called-number 399[89].... dtmf-relay sip-notify codec g711ulaw no vad ! dial-peer voice 1 pots incoming called-number . direct-inward-dial ! dial-peer voice 2 voip incoming called-number . no vad ! dial-peer voice 1000 voip destination-pattern [12]... session target ipv4:10.1.200.21 dtmf-relay h245-alphanumeric no vad ! gateway timer receive-rtp 1200 ! ! gatekeeper shutdown ! ! telephony-service max-ephones 20 max-dn 20 ip source-address 10.1.202.1 port 2000 sdspfarm units 4 sdspfarm transcode sessions 10 sdspfarm tag 1 mtp001ae2a4c080 max-conferences 8 gain -6 call-forward pattern .T transfer-system full-consult transfer-pattern .T ! ! ephone-dn 1 number 3001 name phone 1 ! ! ephone-dn 2 number 3002 name phone 2 ! ! ephone-dn 3 number 3003 name phone 3 ! ! ephone-dn 4 number 3004 name phone 4 ! ! ephone 1 mac-address 0011.9284.8D30 button 1:1 ! ! ! ephone 2 mac-address 001D.A2B7.B43D button 1:2 ! ! ! ephone 3 mac-address 001D.A2B8.013C button 1:3 ! ! ! ephone 4 mac-address 001B.D5E7.D0FD button 1:4 ! ! ! line con 0 line 25 no activation-character no exec transport preferred none transport input all transport output all line aux 0 line vty 0 4 password cisco login transport preferred none ! ! end BR2#