The Physical interface did have frame-relay traffic-shaping configured. Here is another configuration using GNS3 this time. Same problem. no output from show policy-map int s0/0.1.
interface Serial0/0 no ip address encapsulation frame-relay clock rate 2000000 frame-relay traffic-shaping ! interface Serial0/0.1 point-to-point bandwidth 384 snmp trap link-status frame-relay interface-dlci 202 ppp Virtual-Template200 class AutoQoS-FR-Se0/0-202 auto qos voip trust fr-atm interface Virtual-Template200 bandwidth 384 ip address 10.254.254.2 255.255.255.252 ppp multilink ppp multilink interleave ppp multilink fragment delay 10 service-policy output AutoQoS-Policy-Trust map-class frame-relay AutoQoS-FR-Se0/0-202 frame-relay cir 384000 frame-relay bc 3840 frame-relay be 0 frame-relay mincir 384000 BR1#sh policy-map int Ser 0/0.1 BR1# From: wilfred d'souza [mailto:wilfred_the...@yahoo.co.in] Sent: Sunday, June 07, 2009 3:29 PM To: Clawson, Von Subject: Re: [OSL | CCIE_Voice] Auto Qos on the WAN Hey, This could be because you do not have frame-relay traffic-shaping under the main interface Thanks, Wilfred --- On Sun, 7/6/09, Clawson, Von <von.claw...@nexusis.com<mailto:von.claw...@nexusis.com>> wrote: From: Clawson, Von <von.claw...@nexusis.com<mailto:von.claw...@nexusis.com>> Subject: [OSL | CCIE_Voice] Auto Qos on the WAN To: "ccie_voice@onlinestudylist.com<mailto:ccie_voice@onlinestudylist.com>" <ccie_voice@onlinestudylist.com<mailto:ccie_voice@onlinestudylist.com>> Date: Sunday, 7 June, 2009, 4:56 AM I’m running auto qos for the WAN for a 384K link using MLPP. The auto qos presents the following configuration policy-map AutoQoS-Policy-Trust class AutoQoS-VoIP-RTP-Trust priority percent 70 class AutoQoS-VoIP-Control-Trust no band bandwidth percent 5 class class-default fair-queue interface Serial0/0/0:0.1 point-to-point bandwidth 384 ip ospf mtu-ignore frame-relay interface-dlci 201 ppp Virtual-Template200 class AutoQoS-FR-Se0/0/0:0-201 auto qos voip trust fr-atm interface Virtual-Template200 bandwidth 384 ip address 162.2.101.1 255.255.255.0 ppp multilink ppp multilink fragment delay 10 ppp multilink interleave service-policy output AutoQoS-Policy-Trust map-class frame-relay AutoQoS-FR-Se0/0/0:0-201 frame-relay cir 384000 frame-relay bc 3840 frame-relay be 0 frame-relay mincir 384000 The problem is in trying to verify it. I run the following but get no output sh policy-map int Serial0/0/0:0.1 No change has been made to the configuration after the auto qos. Can you not verify with this command using MLPP? Von Clawson Sr. Voice Engineer Nexus IS Technical Assistance Center Nexus IS, Inc. Office: 480.517.6672 Mobile: 480.200.1918 Fax: 480.517.6673 von.claw...@nexusis.com<http://sg.mc87.mail.yahoo.com/mc/compose?to=von.claw...@nexusis.com> www.nexusis.com<http://www.nexusis.com/> [cid:image001.gif@01C9E797.727618F0][cid:image002....@01c9e797.727618f0] The information contained in this email and any additional attachments is confidential and may be legally privileged. If you are not the intended recipient then you must not use, disseminate, distribute or copy any information contained in this email or any attachments. If you receive this email in error, please destroy it immediately and contact us . Thank you. ________________________________ New Email names for you! <http://sg.rd.yahoo.com/sg/mail/domainchoice/mail/signature/*http:/mail.promotions.yahoo.com/newdomains/sg/> Get the Email name you've always wanted on the new @ymail and @rocketmail. Hurry before someone else does!
<<inline: image001.gif>>
<<inline: image002.jpg>>
