Hopefully someone can tell me that I'm off my rocker... I've spent several
hours over the course of two nights looking at this, thinking that I MUST be
doing something wrong, but the only answer I can come up with is that the
PSTN config is off.  This is using ProctorLabs.com, and IPx Vol 1 Lab 5C.  I
see the line about the fan that's failed, but was on a different pod of
equipment last night, so I don't believe this to be hardware-related.

Calls from HQ phones to 911 are failing.  My PSTN phone rings for a partial
ring, then my HQ-RTR sends a disconnect to the PSTN, with the message "Cause
i = 0x80AC - Requested circuit/channel not available".

You'll notice that the PSTN is set up with the B-Channels split...
"pri-group timeslots 1-3,23-24"...  Is that a valid config?  I've never seen
that before, but assumed that I must be the problem.  Initially I had my
pri-group set up for 1-3,24, but then also changed it to match the PSTN
config.  I've tried ascending and descending for B-channel selection.
Initially I was sending the digits "911" as unknown/unknown, but just for
grins, tried translating that to ISDN/subscriber.  Nothing changes the cause
code that I send to the PSTN.

Relevant portions of the config are below.  Please, someone, tell me I'm an
idiot, or tell me that the PSTN config is wrong.  I'm leaning towards the
latter (though the two options may not be mutually exclusive), but I just
can't believe that I'm the first one to run up against a bad config on an
early-stage lab, such that it wouldn't be changed already.  Maybe you guys
are all just jumping straight to Volume 2?

Thanks!

Scott



PSTN Config
!
voice translation-rule 212
 rule 1 /^1212/ /1234/
 rule 2 /^1/ /\0/
 rule 3 /^394/ /\0/
 rule 4 /^011/ /\0/
 rule 5 /^212/ /\0/
 rule 6 /^911$/ /\0/
 rule 9 /./ /1234/
!
voice translation-profile block-call-into-HQ
 translate called 212
!
controller T1 0/3/0
 framing esf
 clock source internal
 linecode b8zs
 pri-group timeslots 1-3,23-24
 description ** T1 VOICE CONNECTION TO HQ-RTR **
!
interface Serial0/3/0:23
 description ** T1 PRI D-CHANNEL TO HQ-RTR **
 no ip address
 encapsulation hdlc
 isdn switch-type primary-ni
 isdn protocol-emulate network
 isdn incoming-voice voice
 isdn outgoing display-ie
 no cdp enable
!
voice-port 0/3/0:23
 translation-profile incoming block-call-into-HQ
 translation-profile outgoing display-proper-ani-into-HQ
 description ** PRI VOICE TRUNK TO HQ-RTR **
!


HQ Config
!
voice translation-rule 911
 rule 1 /911/ /911/ type any subscriber plan any isdn
!
voice translation-profile 911_OUT
 translate called 911
!
controller T1 0/0/0
 framing esf
 linecode b8zs
 pri-group timeslots 1-3,23-24
!
interface Serial0/0/0:23
 no ip address
 encapsulation hdlc
 isdn switch-type primary-ni
 isdn incoming-voice voice
 isdn bchan-number-order ascending
 isdn outgoing display-ie
 no cdp enable
!
dial-peer voice 911 pots
 translation-profile outgoing 911_OUT
 destination-pattern 911
 clid strip name
 port 0/0/0:23
 forward-digits 3



PSTN - debug isdn q931

Jul  9 07:42:08.670: %ENVMON-3-FAN_FAILED: Fan 1 not rotating

Jul  9 07:42:38.562: ISDN Se0/3/0:23 Q931: RX <- SETUP pd = 8  callref =
0x008C
    Bearer Capability i = 0x8090A2
        Standard = CCITT
        Transfer Capability = Speech
        Transfer Mode = Circuit
        Transfer Rate = 64 kbit/s
    Channel ID i = 0xA98381
        Exclusive, Channel 1
    Calling Party Number i = 0x2181, '2123945002'
        Plan:ISDN, Type:National
    Called Party Number i = 0xC1, '911'
        Plan:ISDN, Type:Subscriber(local)
Jul  9 07:42:38.590: ISDN Se0/3/0:23 Q931: TX -> CALL_PROC pd = 8  callref =
0x808C
    Channel ID i = 0xA98381
        Exclusive, Channel 1
Jul  9 07:42:38.598: ISDN Se0/3/0:23 Q931: TX -> ALERTING pd = 8  callref =
0x808C
    Progress Ind i = 0x8188 - In-band info or appropriate now available
Jul  9 07:42:38.670: %ENVMON-3-FAN_FAILED: Fan 1 not rotating

Jul  9 07:42:38.818: ISDN Se0/3/0:23 Q931: RX <- DISCONNECT pd = 8  callref
= 0x008C
    Cause i = 0x80AC - Requested circuit/channel not available
Jul  9 07:42:38.822: ISDN Se0/3/0:23 Q931: TX -> RELEASE pd = 8  callref =
0x808C
Jul  9 07:42:38.834: ISDN Se0/3/0:23 Q931: RX <- RELEASE_COMP pd = 8
callref = 0x008C



Scott
http://ccie.meganandscott.com
Blogging my way to my 8/16/2010 lab exam date
_______________________________________________
For more information regarding industry leading CCIE Lab training, please visit 
www.ipexpert.com

Reply via email to