While it's no required to have the last ",24" on the end of the pri-group command, it does work just fine. IOS still assumes that last channel as the D channel. Just did it now for a quick sanity check. In fact, if the D channel were incorrect, there would be no way that I'd get the partial ring and see the Q931 traffic on the PSTN side.
My original config was without timeslot 23, so it was "pri-group timeslots 1-3,24". In fact, that config is pre-loaded with lab 5C. I changed it to "1-3,23-24" after seeing that the PSTN config was that way. I'm ready to scream... I've wasted 2 ProctorLabs sessions on this lab already, and am now into my third day with it. I want to understand it, but am at the point where I'm about ready to say forget it and move on. I can't get calls to work out BR1 either. I've followed the proctor guide step by step, but still neither HQ nor BR1 work. According to the proctor guide, all I need to do is set up call routing on CUCM and add a dial-peer to the H323 gateway. If I can't get those working, the rest of the lab is pretty much impossible. Scott http://ccie.meganandscott.com Blogging my way to my 8/16/2010 lab exam date On Fri, Jul 9, 2010 at 8:46 AM, Berry, Matthew J. <[email protected]>wrote: > Scott – > > > > You need to change the “pri-group timeslots 1-3,23-24” to "pri-group > timeslots 1-3” (H.323 gateway) or “pri-group timeslots 1-3 service mgcp” > (MGCP gateway). > > > > If you look at your running config, IOS will add the “,24” for the D > channel of the circuit. However, if you try to copy your config and paste > it into a blank router, the system will not see the 24 as the D channel. > Instead, it will assume that you are using 1,2,3, and 24 as B CHANNELS. > > > > You also need a dial-peer for inbound POTS calls. > > > > Dial-peer voice 1 pots > > Direct-inward-dial > > Incoming called-number . > > > > Without this, you will be forced to use dial-peer zero which is a big > no-no. > > > > Give it a shot and let me know. > > > > HTH > > > > *Matthew Berry*, *CCVP*, Sr. Unified Communications Engineer > > [email protected] <[email protected]> > > > > *From:* [email protected] [mailto: > [email protected]] *On Behalf Of *Scott Newberry > *Sent:* Thursday, July 08, 2010 11:01 PM > *To:* [email protected] > *Subject:* [OSL | CCIE_Voice] Call to PSTN fails - Volume 1 Lab 5C > > > > Hopefully someone can tell me that I'm off my rocker... I've spent several > hours over the course of two nights looking at this, thinking that I MUST be > doing something wrong, but the only answer I can come up with is that the > PSTN config is off. This is using ProctorLabs.com, and IPx Vol 1 Lab 5C. I > see the line about the fan that's failed, but was on a different pod of > equipment last night, so I don't believe this to be hardware-related. > > Calls from HQ phones to 911 are failing. My PSTN phone rings for a partial > ring, then my HQ-RTR sends a disconnect to the PSTN, with the message "Cause > i = 0x80AC - Requested circuit/channel not available". > > You'll notice that the PSTN is set up with the B-Channels split... > "pri-group timeslots 1-3,23-24"... Is that a valid config? I've never seen > that before, but assumed that I must be the problem. Initially I had my > pri-group set up for 1-3,24, but then also changed it to match the PSTN > config. I've tried ascending and descending for B-channel selection. > Initially I was sending the digits "911" as unknown/unknown, but just for > grins, tried translating that to ISDN/subscriber. Nothing changes the cause > code that I send to the PSTN. > > Relevant portions of the config are below. Please, someone, tell me I'm an > idiot, or tell me that the PSTN config is wrong. I'm leaning towards the > latter (though the two options may not be mutually exclusive), but I just > can't believe that I'm the first one to run up against a bad config on an > early-stage lab, such that it wouldn't be changed already. Maybe you guys > are all just jumping straight to Volume 2? > > Thanks! > > Scott > > > > PSTN Config > ! > voice translation-rule 212 > rule 1 /^1212/ /1234/ > rule 2 /^1/ /\0/ > rule 3 /^394/ /\0/ > rule 4 /^011/ /\0/ > rule 5 /^212/ /\0/ > rule 6 /^911$/ /\0/ > rule 9 /./ /1234/ > ! > voice translation-profile block-call-into-HQ > translate called 212 > ! > controller T1 0/3/0 > framing esf > clock source internal > linecode b8zs > pri-group timeslots 1-3,23-24 > description ** T1 VOICE CONNECTION TO HQ-RTR ** > ! > interface Serial0/3/0:23 > description ** T1 PRI D-CHANNEL TO HQ-RTR ** > no ip address > encapsulation hdlc > isdn switch-type primary-ni > isdn protocol-emulate network > isdn incoming-voice voice > isdn outgoing display-ie > no cdp enable > ! > voice-port 0/3/0:23 > translation-profile incoming block-call-into-HQ > translation-profile outgoing display-proper-ani-into-HQ > description ** PRI VOICE TRUNK TO HQ-RTR ** > ! > > > HQ Config > ! > voice translation-rule 911 > rule 1 /911/ /911/ type any subscriber plan any isdn > ! > voice translation-profile 911_OUT > translate called 911 > ! > controller T1 0/0/0 > framing esf > linecode b8zs > pri-group timeslots 1-3,23-24 > ! > interface Serial0/0/0:23 > no ip address > encapsulation hdlc > isdn switch-type primary-ni > isdn incoming-voice voice > isdn bchan-number-order ascending > isdn outgoing display-ie > no cdp enable > ! > dial-peer voice 911 pots > translation-profile outgoing 911_OUT > destination-pattern 911 > clid strip name > port 0/0/0:23 > forward-digits 3 > > > > PSTN - debug isdn q931 > > Jul 9 07:42:08.670: %ENVMON-3-FAN_FAILED: Fan 1 not rotating > > Jul 9 07:42:38.562: ISDN Se0/3/0:23 Q931: RX <- SETUP pd = 8 callref = > 0x008C > Bearer Capability i = 0x8090A2 > Standard = CCITT > Transfer Capability = Speech > Transfer Mode = Circuit > Transfer Rate = 64 kbit/s > Channel ID i = 0xA98381 > Exclusive, Channel 1 > Calling Party Number i = 0x2181, '2123945002' > Plan:ISDN, Type:National > Called Party Number i = 0xC1, '911' > Plan:ISDN, Type:Subscriber(local) > Jul 9 07:42:38.590: ISDN Se0/3/0:23 Q931: TX -> CALL_PROC pd = 8 callref > = 0x808C > Channel ID i = 0xA98381 > Exclusive, Channel 1 > Jul 9 07:42:38.598: ISDN Se0/3/0:23 Q931: TX -> ALERTING pd = 8 callref = > 0x808C > Progress Ind i = 0x8188 - In-band info or appropriate now available > Jul 9 07:42:38.670: %ENVMON-3-FAN_FAILED: Fan 1 not rotating > > Jul 9 07:42:38.818: ISDN Se0/3/0:23 Q931: RX <- DISCONNECT pd = 8 callref > = 0x008C > Cause i = 0x80AC - Requested circuit/channel not available > Jul 9 07:42:38.822: ISDN Se0/3/0:23 Q931: TX -> RELEASE pd = 8 callref = > 0x808C > Jul 9 07:42:38.834: ISDN Se0/3/0:23 Q931: RX <- RELEASE_COMP pd = 8 > callref = 0x008C > > > > Scott > http://ccie.meganandscott.com > Blogging my way to my 8/16/2010 lab exam date >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
