What is the extension configured in CUC? 4 digits? If so, then it won't work. Your number you have configured here in SRST is the full 10-dig extension. You would have to add a redirecting voice translation-pattern to match 4-digits to go out and hit the correct extension in CUC.
On Thu, Sep 16, 2010 at 5:10 PM, ayman labib <ayman_la...@yahoo.com> wrote: > Thanks for the reply, > > I have already done that. I reset the gateway(HQ) and still no luck. > Below is my debug from the HQ router (CUC is located in HQ) > > 6178631002 --> User phone number in SRST > 2123945020 --> CUC Pilot number > > Sep 16 15:04:14.631: ISDN Se2/0:23 Q931: RX <- SETUP pd = 8 callref = > 0x00A3 > Bearer Capability i = 0x9090A2 > Standard = CCITT > Transfer Capability = 3.1kHz Audio > Transfer Mode = Circuit > Transfer Rate = 64 kbit/s > Channel ID i = 0xA98381 > Exclusive, Channel 1 > Progress Ind i = 0x8583 - Origination address is non-ISDN > Display i = '+16178631002' > Calling Party Number i = 0x2180, '6178631002' > Plan:ISDN, Type:National > Called Party Number i = 0xA1, '2123945020' > Plan:ISDN, Type:National > Sep 16 15:04:14.643: ISDN Se2/0:23 Q931: TX -> CALL_PROC pd = 8 callref = > 0x80A3 > Channel ID i = 0xA98381 > Exclusive, Channel 1 > Central-GWY# > Sep 16 15:04:14.647: ISDN Se2/0:23 Q931: TX -> ALERTING pd = 8 callref = > 0x80A3 > Progress Ind i = 0x8088 - In-band info or appropriate now available > Sep 16 15:04:14.779: ISDN Se2/0:23 Q931: TX -> CONNECT pd = 8 callref = > 0x80A3 > Display i = 'VoiceMail' > Sep 16 15:04:14.787: ISDN Se2/0:23 Q931: RX <- CONNECT_ACK pd = 8 callref > = 0x00A3 > Central-GWY# > Sep 16 15:04:17.151: ISDN Se2/0:23 Q931: RX <- DISCONNECT pd = 8 callref = > 0x00A3 > Cause i = 0x8290 - Normal call clearing > Sep 16 15:04:17.179: ISDN Se2/0:23 Q931: TX -> RELEASE pd = 8 callref = > 0x80A3 > Sep 16 15:04:17.183: ISDN Se2/0:23 Q931: RX <- RELEASE_COMP pd = 8 callref > = 0x00A3 > > > > ------------------------------ > *From:* Paul Kruger <pauld.kru...@gmail.com> > *To:* ayman labib <ayman_la...@yahoo.com> > > *Cc:* ccie_voice@onlinestudylist.com > *Sent:* Thu, September 16, 2010 11:00:25 AM > *Subject:* Re: [OSL | CCIE_Voice] SRST to UC VoiceMail > > On your HQ GW (or whatever GW is used to reach the CUC) you need to check: > Redirecting Number IE Delivery - Inbound > Redirecting Number IE Delivery - Outbound > > HTH, > Paul > > On Thu, Sep 16, 2010 at 4:53 PM, ayman labib <ayman_la...@yahoo.com>wrote: > >> Greetings, >> >> SRST to Unity Connection VM question. I put my site in SRST, Everything >> works as expected except when I hit the message button to go to my VM box in >> UC. It goes to the general UC message. Under my HQ gateway, I have >> Redirecting number IE inbound and outbound checked. Am I missing any step? >> Any ideas or suggestion is greatly appreciated >> >> My config: >> >> interface Serial0/1/0:23 >> no ip address >> isdn switch-type primary-ni >> isdn incoming-voice voice >> isdn outgoing display-ie >> isdn outgoing ie redirecting-number >> no cdp enable >> ! >> call-manager-fallback >> secondary-dialtone 9 >> max-conferences 8 gain -6 >> transfer-system full-consult >> ip source-address 192.168.31.10 port 2000 strict-match >> max-ephones 10 >> max-dn 10 >> transfer-pattern .T >> voicemail 912123945020 >> call-forward pattern .T >> call-forward busy 912123945020 >> call-forward noan 912123945020 timeout 20 >> moh music-on-hold.au >> multicast moh 239.1.1.1 port 16384 route 192.168.31.10 192.168.31.10 >> time-zone 8 >> ! >> >> >> _______________________________________________ >> For more information regarding industry leading CCIE Lab training, please >> visit www.ipexpert.com >> >> > >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
