Hi, Can you verify that calling number is 10 digits or 7 digits for incoming calls and call type? If it is 10 digits prefix +1, if it is 7 digits prefix +1XXX on the gateway. Regards, Venkat A.
--- On Fri, 11/12/10, Mujaddid Ahmed <mujaddi...@yahoo.com> wrote: From: Mujaddid Ahmed <mujaddi...@yahoo.com> Subject: Re: [OSL | CCIE_Voice] + Dialing issue To: "Shrini" <linuxbos...@gmail.com> Cc: ccie_voice@onlinestudylist.com Date: Friday, November 12, 2010, 2:51 PM I already stated that i did no mgcp / mgcp on gw, Call flow that you r giving is for outbound calls right? My question is related to globalized display of incoming calls on phone not for the outgoing calls. From: Shrini <linuxbos...@gmail.com> To: Mujaddid Ahmed <mujaddi...@yahoo.com> Cc: ShinGei Yong <shingei.y...@gmail.com>; ccie_voice@onlinestudylist.com Sent: Fri, November 12, 2010 1:06:11 PM Subject: Re: [OSL | CCIE_Voice] + Dialing issue mgcp does not reset if you reset on CUCM. You have to enter "no mgcp' and "mgcp" on router. Prefix is added on CUCM only. It depends where you are adding. Call flow is : Called number -> Translation -pattern -> route pattern -> GW -> transformation pattern -> (debug isdn q931). Run debug isdn q931 and see what is the called and calling party number and type. On 11/11/2010 10:22 PM, Mujaddid Ahmed wrote: mgcp connection resets when we reset it from cucm, also the intelligence part to display on phone is done on cucm, gateway just provides information about the calling number type in isdn messages. please correct me if i am wrong. prefix was added on cucm as per the type of the call. From: ShinGei Yong <shingei.y...@gmail.com> To: Shrini <linuxbos...@gmail.com>; ccie_voice@onlinestudylist.com Cc: Mujaddid Ahmed <mujaddi...@yahoo.com> Sent: Fri, November 12, 2010 9:52:00 AM Subject: Re: [OSL | CCIE_Voice] + Dialing issue Hi Shrini, Can you ensure that the UCM mgcp config pump into the gateway correctly? Do a " sh ccm-manager" to verify. Shingei On Fri, Nov 12, 2010 at 2:01 AM, Shrini <linuxbos...@gmail.com> wrote: Hi Iftikhar, In the translation pattern 9.1[2-9]XX[2-9]XXXXXX --> under calling party transformation select the check box use calling part's external phone mask. Calling party transform mask - XXXXXXXXXXX Calling /called party number type : National Calling/Called party numbering plan : ISDN In Gateway: Under Incoming calling part settings: Change the prefix to + from Default for National numbers. You will get +1XXXXXXXXXX as calling party displayed on phone and missed calls Thx Shrini On 11/10/2010 11:55 PM, Mujaddid Ahmed wrote: Hi, Please confirm what can be the reason of globalization not working with cisco 7965 phones. I globalized it on CUCM gateway configuration by adding appropriate prefix on type of calls. did, no mgcp / mgcp on gateway and reset the gateway from cucm as well. call lands on phone and still shows only 7 digit calling number in both ringing and missed call. nothing has been set so far in Device pool or on device to effect the globalization done on Gateway. Is there any serivce parameter or any command on router that can prevent the globalize display on phone? Please help, as i wasted lot of time in troubleshooting this particular issue in a very time critical environment. Regards, Iftikhar Ahmed _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com -----Inline Attachment Follows----- _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com