Thank you too much Amit for your help, Kindly find the configuration below. I think I tried to enable multicast on both gig and loopback but it does not solve the problem. I will test it now
BR02-CME#sho run Building configuration... Current configuration : 5120 bytes ! ! Last configuration change at 02:38:04 UTC Tue Mar 2 1993 ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname BR02-CME ! boot-start-marker boot system flash c2800nm-adventerprisek9-mz.124-20.T2.bin boot-end-marker ! card type e1 0 0 ! card type command needed for slot/vwic-slot 1/0 logging message-counter syslog enable password cisco ! no aaa new-model no network-clock-participate slot 1 network-clock-participate wic 0 ! dot11 syslog ip source-route ! ! ip cef ip dhcp excluded-address 10.30.10.200 10.30.10.254 ip dhcp excluded-address 10.30.20.200 10.30.20.254 ! ip dhcp pool DATA network 10.30.10.0 255.255.255.0 default-router 10.30.10.254 ! ip dhcp pool Voice network 10.30.20.0 255.255.255.0 default-router 10.30.20.254 option 150 ip 10.10.10.10 ! ! no ip domain lookup ip multicast-routing no ipv6 cef ! multilink bundle-name authenticated ! ! isdn switch-type primary-net5 ! ! ! voice service voip allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip ! ! ! ! ! ! ! ! ! ! ! ! ! ! voice translation-rule 1 rule 1 /^12345\(4...\)/ /\1/ ! ! voice translation-profile in translate called 1 ! ! voice-card 0 no dspfarm dsp services dspfarm ! ! ! ! ! archive log config hidekeys ! ! ! ! ! controller E1 0/0/0 framing NO-CRC4 clock source internal linecode ami pri-group timeslots 1-3,16 ! ! ! ! ! interface Loopback0 ip address 10.30.30.254 255.255.255.0 ip pim dense-mode ! interface GigabitEthernet0/0 ip address 10.30.20.254 255.255.255.0 ip pim dense-mode duplex auto speed auto h323-gateway voip interface h323-gateway voip bind srcaddr 10.30.20.254 ! interface Service-Engine0/0 ip unnumbered GigabitEthernet0/0 service-module ip address 10.30.20.253 255.255.255.0 service-module ip default-gateway 10.30.20.254 ! interface GigabitEthernet0/1 ip address 192.168.2.2 255.255.255.252 duplex auto speed auto ! interface Serial0/0/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn incoming-voice voice no cdp enable ! router ospf 1 log-adjacency-changes redistribute connected network 10.30.10.0 0.0.0.255 area 0 network 10.30.20.0 0.0.0.255 area 0 network 192.168.2.0 0.0.0.3 area 0 ! ip forward-protocol nd ip route 10.30.20.253 255.255.255.255 Service-Engine0/0 ip http server ip http authentication local no ip http secure-server ip http path flash:/GUI ! ! ! ! ! ! ! ! ! control-plane ! ! ! voice-port 0/0/0:15 ! voice-port 0/1/0 station-id name CME PSTN Number station-id number 6000 ! voice-port 0/1/1 ! ccm-manager music-on-hold bind Loopback0 ! ! sccp local GigabitEthernet0/0 sccp ccm 10.10.10.11 identifier 2 priority 2 version 6.0 sccp ccm 10.10.10.10 identifier 1 priority 1 version 6.0 sccp ! sccp ccm group 1 associate ccm 1 priority 1 associate ccm 2 priority 2 associate profile 1 register XCODER ! dspfarm profile 1 transcode codec g711ulaw codec g711alaw codec g729ar8 codec g729abr8 codec g729r8 maximum sessions 1 associate application SCCP ! ! dial-peer voice 100 pots service aa destination-pattern 6000 port 0/1/0 ! dial-peer voice 1001 voip destination-pattern 4... session target ipv4:10.10.10.10 ! dial-peer voice 1004 voip translation-profile incoming in translation-profile outgoing in answer-address 123454... destination-pattern 123454... session target ipv4:10.30.20.254 ! dial-peer voice 4220 voip destination-pattern 4220$ session protocol sipv2 session target ipv4:10.30.20.253 dtmf-relay sip-notify codec g711ulaw no vad ! ! sip-ua mwi-server ipv4:10.30.20.253 expires 3600 port 5060 transport udp unsolicited ! ! ! telephony-service srst mode auto-provision dn max-ephones 3 max-dn 10 no-reg both ip source-address 10.30.20.254 port 2000 voicemail 4220 max-conferences 8 gain -6 moh music-on-hold.au multicast moh 239.1.1.1 port 16384 route 10.30.20.254 10.30.30.254 dn-webedit time-webedit transfer-system full-consult secondary-dialtone 9 create cnf-files version-stamp Jan 01 2002 00:00:00 ! ! ephone-dn-template 1 call-forward busy 4220 call-forward noan 4220 timeout 20 mwi sip huntstop channel 1 ! ! ephone-dn 1 number 4001 name BR2PHone1 ephone-dn-template 1 ! ! ephone-dn 2 number 4002 label 4002 line con 0 line aux 0 line 194 no activation-character no exec transport preferred none transport input all transport output lat pad telnet rlogin lapb-ta mop udptn v120 ssh line vty 0 4 password cisco login ! scheduler allocate 20000 1000 ntp source GigabitEthernet0/0 ntp server 10.10.10.254 end BR02-CME# BR02-CME# BR02-CME# ________________________________ From: amit batra <batraji...@yahoo.com> To: Ccie Voice <v.c...@yahoo.com> Sent: Sat, March 5, 2011 3:55:25 AM Subject: Re: [OSL | CCIE_Voice] Multicast MoH for Remote branches Mate order is not important ... but make sure its there .. also if it still doesnt help... Enable multicast on the lookback interface with command pim dense-mode. i hope this helps .. --- On Sat, 3/5/11, Ccie Voice <v.c...@yahoo.com> wrote: >From: Ccie Voice <v.c...@yahoo.com> >Subject: Re: [OSL | CCIE_Voice] Multicast MoH for Remote branches >To: "George Goglidze" <gogli...@gmail.com> >Cc: "CCIE Study" <ccie_voice@onlinestudylist.com> >Date: Saturday, March 5, 2011, 5:14 AM > > > >Yes I configured it, but no luck :( > >I have one question also in the command >multicast moh X.X.X.X port X route IPAddress1 IPAddress2 > >Is there any order I should follow or I can put Lo0 and Voice Vlan in >IPAddress1 >and IPAddress2 in any order? > > > > > > ________________________________ From: George Goglidze <gogli...@gmail.com> >To: Ccie Voice <v.c...@yahoo.com> >Cc: ccieid1ot <ccieid...@gmail.com>; CCIE Study <ccie_voice@onlinestudylist.com> >Sent: Sat, March 5, 2011 2:28:00 AM >Subject: Re: [OSL | CCIE_Voice] Multicast MoH for Remote branches > >do you have "ccm-manager music-on-hold" ??? this is needed for PSTN to hear >moh. > >Regards, > > >On Fri, Mar 4, 2011 at 9:46 PM, Ccie Voice <v.c...@yahoo.com> wrote: > >I just need to add one note: >> >>I stopped the CUCM service, so the phone registered with SRST router at that >>point, if I called from analog phone to IP phone and press hold I can hear >>MoH >>form the flash. >> >> >> >> >> ________________________________ From: ccieid1ot <ccieid...@gmail.com> >>To: Ccie Voice <v.c...@yahoo.com> >>Cc: CCIE Study <ccie_voice@onlinestudylist.com> >>Sent: Sat, March 5, 2011 12:17:33 AM >>Subject: Re: [OSL | CCIE_Voice] Multicast MoH for Remote branches >> >> >>Configs? Make sure under multicast route has the loopback and voice vlan int. >>duy >>ccie #27737 voice >>tmobile g2 >>On Mar 4, 2011 3:14 PM, "Ccie Voice" <v.c...@yahoo.com> wrote: >>> Hi All, >>> >>> I did the following scenario: >>> >>> HQ and BR1 >>> I enabled MoH g711ual Multi-cast and I configured multicast under SRST >>> configuration. >>> >>> if BR1-Ph1 called BR1-PH2 and press hold I can heat MoH from the flash of >>> BR1 > >>> Router. >>> >>> >>> The problem is when I am calling form PSTN. I have FXS port if called from >>> my > >>> analog phone to BR1-Ph1 and pressed hold I just heat "tot tot tot .....". >>> >>> >>> Any Idea? >>> >>> >>> >>> >> >> >>_______________________________________________ >>For more information regarding industry leading CCIE Lab training, please >>visit >>www.ipexpert.com >> >> > > >-----Inline Attachment Follows----- > > >_______________________________________________ >For more information regarding industry leading CCIE Lab training, please >visit >www.ipexpert.com >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com