Dear All,
I need your help , From my PSTN Phone I am not able to call Br2 IP Phone, PSTN Phone-----PSTN GW----H323 -----Br2 GW-----CUCM7------IP Phone (4001) Please find my log on H323 GW and config below: H323 Br2 GW ============================================== voice service voip allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip sip ! voice class codec 1 codec preference 1 g711ulaw codec preference 2 g729r8 ! voice class h323 1 h225 timeout tcp establish 3 h225 timeout setup 3 ! ! voice translation-rule 1 rule 1 // // type any unknown plan any isdn ! voice translation-rule 2 rule 1 // // type any subscriber plan any isdn ! voice translation-rule 4 rule 1 // // type any international plan any isdn ! voice translation-rule 5 rule 1 /.*\(4...\)$/ /\1/ ! voice translation-rule 11 rule 1 /^4...$/ /2404&/ type any subscriber plan any isdn ! voice translation-rule 12 rule 1 /^4...$/ /2404&/ type any subscriber plan any isdn ! voice translation-rule 14 rule 1 /^4...$/ /+8522404&/ type any international plan any isdn ! ! voice translation-profile 999 translate calling 11 translate called 1 ! voice translation-profile did translate called 5 ! voice translation-profile int translate calling 14 translate called 4 ! voice translation-profile local translate calling 12 translate called 2 ! controller E1 0/0/0 pri-group timeslots 1-4,16 ! interface Serial0/0/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn incoming-voice voice isdn send-alerting isdn sending-complete isdn outgoing display-ie isdn outgoing ie redirecting-number no cdp enable voice-port 0/0/0:15 translation-profile incoming did dial-peer voice 5 pots destination-pattern . direct-inward-dial ! dial-peer voice 1 pots translation-profile outgoing 999 destination-pattern 999 no digit-strip port 0/0/0:15 ! dial-peer voice 11 voip destination-pattern 4...$ voice-class codec 1 voice-class h323 1 session target ipv4:142.100.64.11 dtmf-relay h245-alphanumeric no vad ! ==================ISDN logs on BR2 H323 GW=================== ar 12 08:09:15.956: ISDN Se0/0/0:15 Q931: RX <- SETUP pd = 8 callref = 0x0091 Sending Complete Sending Complete Standard = CCITT Transfer Capability = Speech Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA98381 Exclusive, Channel 1 Progress Ind i = 0x8183 - Origination address is non-ISDN Display i = 'Nisha' Calling Party Number i = 0x0180, '911' Plan:ISDN, Type:Unknown Called Party Number i = 0x81, '24044002' Plan:ISDN, Type:Unknown *Mar 12 08:09:15.976: ISDN Se0/0/0:15 Q931: TX -> CALL_PROC pd = 8 callref = 0x 8091 Channel ID i = 0xA98381 Exclusive, Channel 1 *Mar 12 08:09:15.976: ISDN Se0/0/0:15 Q931: TX -> CONNECT pd = 8 callref = 0x80 91 *Mar 12 08:09:15.992: ISDN Se0/0/0:15 Q931: RX <- CONNECT_ACK pd = 8 callref = 0x0091 *Mar 12 08:09:15.992: %ISDN-6-CONNECT: Interface Serial0/0/0:0 is now connected to 911 N/A *Mar 12 08:09:21.992: %ISDN-6-CONNECT: Interface Serial0/0/0:0 is now connected to 911 N/A It is showing connected on IP Phone and this log also but BR2-IP Phone not ringing. Raj
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com