does the config appear at any point? try restarting the router first, and then try to register phone to srst again. do the phone ever register with srst?
can you do, show ephone register when the phone are registered to the cucme, and show run at that moment too? On Sat, Apr 30, 2011 at 6:47 PM, donny f <f.faraday...@gmail.com> wrote: > tks , i am using prcotorlab ,so i believe 12.4.15 > > what i miss here ? > > config > > telep-service > max-dn 10 > max-ephone 5 > ip soure 10.1.202.1 po 2000 > srst moe autorpv all > ! > > that is it > > On Sat, Apr 30, 2011 at 11:15 AM, George Goglidze <gogli...@gmail.com>wrote: > >> Hi guys, >> >> with telephony-service in srst mode, with "srst mode autoprovision all", >> when the phone register, with the help of SNAP protocol CUCME will "read" >> all information from the .cnf file that is in the phone itself, and create >> ephone-dn, and ephone's in the running configuration... >> >> After the phone un-registers from the CUCME, and registers back to CUCM, >> this configuration will stay in "running-configuration", until you reboot >> the router, which will start with startup-configuration again. and if you >> save it before reload, then it will stay there. >> >> So Donny, the behavior you're experiencing is not normal. Show us the >> configuration please, and the IOS you're running. >> >> Regards, >> >> On Sat, Apr 30, 2011 at 2:02 PM, Julien Krieger <krieger.jul...@gmail.com >> > wrote: >> >>> Hi Donny, >>> >>> You are right but the display is only fonctionnal when you are in srst >>> mode and phone are registered on the srst gateway. >>> >>> As soon as the srst process turns down because phone unregister from srst >>> gateway and register back on CUCM, there are nothing anymore to display on >>> the srst gateway config about phone. >>> >>> Test this: >>> 1/ sh run when CUCM is not reachable and that your phones have registered >>> on the srst gateway. You will display you phone config (all phone becomes >>> dial-peer, etc...) >>> >>> 2/ sh run when your phone have unregistered from srst gateway and >>> registered back to CUCM. Nothing to display anymore... >>> >>> Again and again... >>> >>> Do you see what I mean? >>> I hope this help you to understand. >>> >>> Julien >>> >>> >>> 2011/4/29 donny f <f.faraday...@gmail.com> >>> >>>> hi julien, >>>> >>>> as per cisco SRND/doc. >>>> >>>> there are 3 auto prov (none, dn,all) >>>> >>>> and when we back to UCM from SRST, we should see the ephone and dn for >>>> auto prov all. (that is why there is "none" optio ) >>>> >>>> Am I misunderstand it ? >>>> >>>> On Fri, Apr 29, 2011 at 6:55 AM, Julien Krieger < >>>> krieger.jul...@gmail.com> wrote: >>>> >>>>> When your IPPhones register on SRST gateway, gateway learn all ipphones >>>>> configuration and translate it into dial-peers. With "srst mode >>>>> autoprovision all" command you can read the built configuration from a >>>>> "show >>>>> run" thanks to that command. >>>>> >>>>> When UCM is available again, your ipphones unregister from SRST gateway >>>>> to register back to UCM. therefore, there is no configuration left in the >>>>> gateway... I guess this is why you don't see any configuration after >>>>> re-register to UCM. >>>>> >>>>> 2011/4/29 donny f <f.faraday...@gmail.com> >>>>> >>>>>> hi exp, >>>>>> >>>>>> I use "srst mode autoprovisio all" under telephony-service. >>>>>> >>>>>> However when i back from CME mode to UCM , my ephone-dn and ephone do >>>>>> not stay in sh run >>>>>> >>>>>> Is that expected ? what i missed ? >>>>>> >>>>>> _______________________________________________ >>>>>> For more information regarding industry leading CCIE Lab training, >>>>>> please visit www.ipexpert.com >>>>>> >>>>>> Are you a CCNP or CCIE and looking for a job? Check out >>>>>> www.PlatinumPlacement.com <http://www.platinumplacement.com/> >>>>>> >>>>> >>>>> >>>> >>> >>> _______________________________________________ >>> For more information regarding industry leading CCIE Lab training, please >>> visit www.ipexpert.com >>> >>> Are you a CCNP or CCIE and looking for a job? Check out >>> www.PlatinumPlacement.com <http://www.platinumplacement.com/> >>> >> >> >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
