today i got it work fine, not sure what i wrong in Proctorlab other day. On Sat, Apr 30, 2011 at 12:45 PM, George Goglidze <gogli...@gmail.com>wrote:
> does the config appear at any point? > > try restarting the router first, and then try to register phone to srst > again. > do the phone ever register with srst? > > can you do, show ephone register when the phone are registered to the > cucme, and show run at that moment too? > > > On Sat, Apr 30, 2011 at 6:47 PM, donny f <f.faraday...@gmail.com> wrote: > >> tks , i am using prcotorlab ,so i believe 12.4.15 >> >> what i miss here ? >> >> config >> >> telep-service >> max-dn 10 >> max-ephone 5 >> ip soure 10.1.202.1 po 2000 >> srst moe autorpv all >> ! >> >> that is it >> >> On Sat, Apr 30, 2011 at 11:15 AM, George Goglidze >> <gogli...@gmail.com>wrote: >> >>> Hi guys, >>> >>> with telephony-service in srst mode, with "srst mode autoprovision all", >>> when the phone register, with the help of SNAP protocol CUCME will "read" >>> all information from the .cnf file that is in the phone itself, and create >>> ephone-dn, and ephone's in the running configuration... >>> >>> After the phone un-registers from the CUCME, and registers back to CUCM, >>> this configuration will stay in "running-configuration", until you reboot >>> the router, which will start with startup-configuration again. and if you >>> save it before reload, then it will stay there. >>> >>> So Donny, the behavior you're experiencing is not normal. Show us the >>> configuration please, and the IOS you're running. >>> >>> Regards, >>> >>> On Sat, Apr 30, 2011 at 2:02 PM, Julien Krieger < >>> krieger.jul...@gmail.com> wrote: >>> >>>> Hi Donny, >>>> >>>> You are right but the display is only fonctionnal when you are in srst >>>> mode and phone are registered on the srst gateway. >>>> >>>> As soon as the srst process turns down because phone unregister from >>>> srst gateway and register back on CUCM, there are nothing anymore to >>>> display >>>> on the srst gateway config about phone. >>>> >>>> Test this: >>>> 1/ sh run when CUCM is not reachable and that your phones have >>>> registered on the srst gateway. You will display you phone config (all >>>> phone >>>> becomes dial-peer, etc...) >>>> >>>> 2/ sh run when your phone have unregistered from srst gateway and >>>> registered back to CUCM. Nothing to display anymore... >>>> >>>> Again and again... >>>> >>>> Do you see what I mean? >>>> I hope this help you to understand. >>>> >>>> Julien >>>> >>>> >>>> 2011/4/29 donny f <f.faraday...@gmail.com> >>>> >>>>> hi julien, >>>>> >>>>> as per cisco SRND/doc. >>>>> >>>>> there are 3 auto prov (none, dn,all) >>>>> >>>>> and when we back to UCM from SRST, we should see the ephone and dn for >>>>> auto prov all. (that is why there is "none" optio ) >>>>> >>>>> Am I misunderstand it ? >>>>> >>>>> On Fri, Apr 29, 2011 at 6:55 AM, Julien Krieger < >>>>> krieger.jul...@gmail.com> wrote: >>>>> >>>>>> When your IPPhones register on SRST gateway, gateway learn all >>>>>> ipphones configuration and translate it into dial-peers. With "srst mode >>>>>> autoprovision all" command you can read the built configuration from a >>>>>> "show >>>>>> run" thanks to that command. >>>>>> >>>>>> When UCM is available again, your ipphones unregister from SRST >>>>>> gateway to register back to UCM. therefore, there is no configuration >>>>>> left >>>>>> in the gateway... I guess this is why you don't see any configuration >>>>>> after >>>>>> re-register to UCM. >>>>>> >>>>>> 2011/4/29 donny f <f.faraday...@gmail.com> >>>>>> >>>>>>> hi exp, >>>>>>> >>>>>>> I use "srst mode autoprovisio all" under telephony-service. >>>>>>> >>>>>>> However when i back from CME mode to UCM , my ephone-dn and ephone >>>>>>> do not stay in sh run >>>>>>> >>>>>>> Is that expected ? what i missed ? >>>>>>> >>>>>>> _______________________________________________ >>>>>>> For more information regarding industry leading CCIE Lab training, >>>>>>> please visit www.ipexpert.com >>>>>>> >>>>>>> Are you a CCNP or CCIE and looking for a job? Check out >>>>>>> www.PlatinumPlacement.com <http://www.platinumplacement.com/> >>>>>>> >>>>>> >>>>>> >>>>> >>>> >>>> _______________________________________________ >>>> For more information regarding industry leading CCIE Lab training, >>>> please visit www.ipexpert.com >>>> >>>> Are you a CCNP or CCIE and looking for a job? Check out >>>> www.PlatinumPlacement.com <http://www.platinumplacement.com/> >>>> >>> >>> >> >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
