It looks like CUE is on line 194, but I can't clear it. BR2-RTR#ser ser 0/0 status Service Module is Cisco Service-Engine0/0 Service Module supports session via TTY line 194 Service Module is in Steady state Service Module heartbeat-reset is enabled Getting status from the Service Module, please wait..
May 30 02:47:31.618: %IPPHONE-6-REG_ALARM: 24: Name=SEP001BD4C6C02D Load=8.0(5.0) Last=Phone-Reg-Rej Cisco Unity Express 7.0.1 CUE Running on AIM BR2-RTR# BR2-RTR# May 30 02:47:51.967: %IPPHONE-6-REG_ALARM: 24: Name=SEP0011BBEF76A9 Load=8.0(5.0) Last=Phone-Reg-Rej BR2-RTR#clear line 194 [confirm] [OK] BR2-RTR#show line Tty Line Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int * 0 0 CTY - - - - - 11 1 0/0 - 1 1 AUX 9600/9600 - - - - - 0 0 0/0 - 194 194 TTY 9600/9600 - - - - - 11 0 0/0 - 514 514 VTY - - - - - 0 0 0/0 - 515 515 VTY - - - - - 0 0 0/0 - 516 516 VTY - - - - - 0 0 0/0 - 517 517 VTY - - - - - 0 0 0/0 - 518 518 VTY - - - - - 0 0 0/0 - 519 519 VTY - - - - - 0 0 0/0 - 520 520 VTY - - - - - 0 0 0/0 - 521 521 VTY - - - - - 0 0 0/0 - 522 522 VTY - - - - - 0 0 0/0 - 523 523 VTY - - - - - 0 0 0/0 - 524 524 VTY - - - - - 0 0 0/0 - 525 525 VTY - - - - - 0 0 0/0 - 526 526 VTY - - - - - 0 0 0/0 - 527 527 VTY - - - - - 0 0 0/0 - 528 528 VTY - - - - - 0 0 0/0 - 529 529 VTY - - - - - 0 0 0/0 - Line(s) not in async mode -or- with no hardware support: 2-193, 195-513 BR2-RTR# Any other ideas... Thanks, Randall ________________________________ From: Nirvair Sahota <nirvair.sah...@sbcglobal.net> To: Online Study <ccie_voice@onlinestudylist.com>; Randall Crumm <rrcr...@yahoo.com> Sent: Sunday, May 29, 2011 3:28 PM Subject: Re: [OSL | CCIE_Voice] UCME/CUE verify module status "ser ser 0/0 status" and if any issues you may try to reset this module by using, " ser ser 0/0 reset' cmd. --- On Sun, 5/29/11, Randall Crumm <rrcr...@yahoo.com> wrote: >From: Randall Crumm <rrcr...@yahoo.com> >Subject: [OSL | CCIE_Voice] UCME/CUE >To: "Online Study" <ccie_voice@onlinestudylist.com> >Date: Sunday, May 29, 2011, 2:07 PM > > >HI, >I'm having a weird issue. (see snipits below) > > >I configured mt CME for CUE(not telephony-service yet) and I cannot ser ser >0/0 ses to it >I can ping 10.10.202.2 from hq rtr >The cli just has a blank like > > >Anyone have an ideas or run into this? > > >Thanks, >Randall > > > > >interface Service-Engine0/0 > ip unnumbered Vlan400 > service-module ip address 10.10.202.2 255.255.255.0 > service-module ip default-gateway 10.10.202.1 > > >ip route 10.10.202.2 255.255.255.255 Service-Engine0/0 > > > > >interface Vlan400 > ip address 10.10.202.1 255.255.255.0 > > > > >-----Inline Attachment Follows----- > > >_______________________________________________ >For more information regarding industry leading CCIE Lab training, please >visit www.ipexpert.com > >Are you a CCNP or CCIE and looking for a job? Check out >www.PlatinumPlacement.com
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
