hi Bill, Also what is the navigation path to this doc . It does seem to be easy to locate once you are moving from the product/ support page.
-MJ On Mon, Dec 31, 2012 at 6:35 PM, Bill <whl...@gmail.com> wrote: > Ps you do not show your policy-map WAN-EDGE so you config is incomplete > > You need to config a class-map, then policy-map, then your nested > policy-map with the shaping, then create your map-class and finally apply > that > > Bill > > > On Dec 31, 2012, at 6:54 AM, sanity insanity < > networksanitytoinsan...@gmail.com> wrote: > > hi Bill and All, > > Thanks for your reply, > > 1) I checked the srnd the part you have pasted does not seem to be present > can u tell it on which page you got this from? > > 2) Also is the configuration I earlier pasted in my email correct? > > 3)I checked the enterprise QOS document . I there an easlier way to > navigate to this document from the default as I could not find the correct > path to it . > > > Thanks once again for your help! > > -MJ > > > > On Mon, Dec 31, 2012 at 1:02 AM, Bill Lake <whl...@gmail.com> wrote: > >> Using the SRND it is fairly easy to cut and paste but here is a full >> sample of class based shaping >> >> class-map match-any RTP >> match ip dscp ef >> >> class-map match any Signal >> match ip dscp cs3 >> >> policy-map queueing >> class RTP >> priority percent 25 >> class Signal >> bandwidth percent 5 >> class class-default >> fair-queue >> police cir percent 50 conform-action transmit exceed-action drop >> >> policy-map SHAPE >> class class-default >> compress header ip rtp >> >> shape average 729600 7296 0 >> service-policy queueing >> >> map-class frame-relay SHAPE >> frame-relay fragment 960 >> service-policy output SHAPE >> >> interface serial 0/0/1:0.1 point-to-point >> frame-relay interface-dlci 101 >> class SHAPE >> >> so you can't use auto qos to do this and once you know this you can use >> auto qos or just do it manually for FRF12. >> >> On Sun, Dec 30, 2012 at 6:44 AM, sanity insanity < >> networksanitytoinsan...@gmail.com> wrote: >> >>> >>> >>> Hi Bill, >>> >>> Thanks for your reply. I shall be therefore using the following config >>> without using >>> auto qos... >>> >>> policy-map MQC-FRTS-768 >>> class class-default >>> shape average 729600 7296 0 ! Enables MQC-Based FRTS >>> service-policy WAN-EDGE ! Queues packets headed to the shaper >>> ! >>> … >>> ! >>> interface Serial2/0 >>> no ip address >>> encapsulation frame-relay >>> ! >>> interface Serial2/0.12 point-to-point >>> ip address 10.1.121.1 255.255.255.252 >>> description 768kbps FR Circuit to RBR-3745-Left >>> frame-relay interface-dlci 102 >>> class FR-MAP-CLASS-768 ! >>> ! >>> … >>> ! >>> map-class frame-relay FR-MAP-CLASS-768 >>> service-policy output MQC-FRTS-768 >>> frame-relay fragment 960 >>> ! >>> >>> >>> Also I will be including the ... >>> >>> interface Serial2/0.12 point-to-point >>> bandwidth 768 >>> >>> for the bandwidth requirement. >>> >>> >>> Questions : >>> >>> 1) I shall be applying the a similar config on the branch router also. >>> Is this correct? Is the above config adequate ? >>> >>> 2)There is also a branch 2 router . Does the config need to applied on >>> the branch 2 even though >>> it is not part of the requirement? >>> >>> 3) Are there any negative impacts of wan qos if the configuration goes >>> incorrect? >>> >>> >>> Thanks once again. >>> >>> -MJ >>> >>> >>> >>> On Tue, Dec 25, 2012 at 8:25 AM, Bill Lake <whl...@gmail.com> wrote: >>> >>>> Have you tried using the Cisco QOS SRND? >>>> >>>> http://www.cisco.com/en/US/docs/solutions/Enterprise/WAN_and_MAN/QoS_SRND/QoS-SRND-Book.html >>>> >>>> Look around at 3-27 >>>> >>>> On Mon, Dec 24, 2012 at 8:44 PM, sanity insanity < >>>> networksanitytoinsan...@gmail.com> wrote: >>>> >>>>> hi Guys, >>>>> >>>>> Can you explain as to how we can achieve the following by ... >>>>> >>>>> Connecting HQ and a branch site is a 384 k frame relay PVC. Enable >>>>> frf.12 Link frag and interleave >>>>> the FR connection to fragment the large data packets and interleave >>>>> the voice packets to >>>>> minimize delays .Maximum delay between fragments should be set at 10ms >>>>> .Also provision RTP >>>>> header compression.We need to assume all bearer voice traffic has been >>>>> marked with DSCP of "EF"and >>>>> all of control traffic CS3. >>>>> >>>>> -MJ >>>>> >>>>> >>>>> _______________________________________________ >>>>> For more information regarding industry leading CCIE Lab training, >>>>> please visit www.ipexpert.com >>>>> >>>>> Are you a CCNP or CCIE and looking for a job? Check out >>>>> www.PlatinumPlacement.com >>>>> >>>> >>>> >>> >> >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com