But would the MVA number still work on the gateway when you dial in? May it would huh because the MVA AA on the IOS is separate?
Regards, Hugo From: William Bell [mailto:b...@ucguerrilla.com] Sent: Wednesday, March 27, 2013 4:47 AM To: Barrera, Hugo Cc: Justin Carney; donny f; ccie_voice@onlinestudylist.com, (ccie_voice@onlinestudylist.com); michael.se...@compucom.com; networksanitytoinsan...@gmail.com Subject: Re: [OSL | CCIE_Voice] MVA partial match issue I have ran into a similar problem. In my case I would get a fast busy after entering the extension number followed by #. The issue was I neglected to provision Mobile Voice Access under Media Resources. On Tuesday, March 26, 2013, Barrera, Hugo wrote: Regarding MVA during my first attempt (real lab) I had it working except for when I dialed in and tried to call another 4-digit ext like SAPH1 or SBPH2 any ideas why that didn't work? Regards, Hugo From: ccie_voice-boun...@onlinestudylist.com<javascript:_e(%7b%7d,%20'cvml',%20'ccie_voice-boun...@onlinestudylist.com');> [mailto:ccie_voice-boun...@onlinestudylist.com<javascript:_e(%7b%7d,%20'cvml',%20'ccie_voice-boun...@onlinestudylist.com');>] On Behalf Of Justin Carney Sent: Monday, March 25, 2013 1:51 AM To: donny f Cc: ccie_voice@onlinestudylist.com<javascript:_e(%7b%7d,%20'cvml',%20'ccie_voice@onlinestudylist.com');>, (ccie_voice@onlinestudylist.com<javascript:_e(%7b%7d,%20'cvml',%20'ccie_voice@onlinestudylist.com');>); michael.se...@compucom.com<javascript:_e(%7b%7d,%20'cvml',%20'michael.se...@compucom.com');>; networksanitytoinsan...@gmail.com<javascript:_e(%7b%7d,%20'cvml',%20'networksanitytoinsan...@gmail.com');> Subject: Re: [OSL | CCIE_Voice] MVA partial match issue You can have the rd with 7 digits only and without the 9 for pstn access - use either application dial rules (match 7 digits, prefix 9) or a translation pattern to modify the rd to match your existing local route pattern. I'm not sure if there's an MVA bug in this version of cucm, but its pretty easy to configure it so that you always have a full match since you will likely have only one rd. This is what I do for the lab. A real world (for nanp) example of MVA partial match would be using e164 address for all rd (+1 npa-nxx-xxxx) and set partial match to 10 or 7 depending on whether all sites receive inbound ani as 10d for local calls or if any sites receives only 7d. This would also work for lab, but takes extra steps if you aren't already required to use + dialing For partial match to work, the rd must be longer than the inbound ani (ani 7d and rd +11d). You cannot use partial match with an ani longer than the rd (ani 10d and rd 7d), in this case your options would be to apply inbound transformation on the gateway to make rd ani shorter (ie match the rd) or make your rd longer and manipulate outbound dnis to make it route. On Mar 25, 2013 2:00 AM, "donny f" <f.faraday...@gmail.com<mailto:f.faraday...@gmail.com>> wrote: hi, I config the Service parameter for MVA , using "partial match" 7 digit . However when I dial the RD using 7 digit ,it never works. seem like UCM only take "Full match". I heard this is bug, Any suggestion for the work around if still want to use "partial match" ? d On Sun, Mar 17, 2013 at 9:58 AM, <michael.se...@compucom.com<mailto:michael.se...@compucom.com>> wrote: Greetings, I think you are doing everything right just need a few tweaks. Place a call from the PSTN line 2 to 3033300 and do debug isdn q931 on gateway. What digits do you see for the calling number. 7 or 10? If seeing 7 digits inbound change your Remote Destination Number to 5252222, without the 9. If you are seeing 10 digits inbound the NPA, NXX, TNTN change your remote destination number to XXX5252222, in other words match what you're seeing in the isdn debug for calling party and make that you're Remote Destination Number. Do NOT require the prefix of 9 on the Remote Destination Number. Also, under Remote Destination Information make sure you are putting a tick in Mobile Phone checkbox and a tick in the Enable Mobile Connect checkbox. Otherwise your configuration looks good. Hope you find this helpful. Michael Sears CCIE 38404 Date: Sun, 17 Mar 2013 18:23:01 +0530 From: sanity insanity <networksanitytoinsan...@gmail.com<mailto:networksanitytoinsan...@gmail.com>> To: ccie_voice@onlinestudylist.com<mailto:ccie_voice@onlinestudylist.com> Subject: [OSL | CCIE_Voice] Mobile Voice Access not working since many days!! Message-ID: <cag4zmyxmd5xj67pwv+_gpabedjoydyg+zbnmugtsfuj3nsx...@mail.gmail.com<mailto:cag4zmyxmd5xj67pwv+_gpabedjoydyg+zbnmugtsfuj3nsx...@mail.gmail.com>> Content-Type: text/plain; charset="iso-8859-1" Hello All, I have been trying this config for MVA for close to 2 weeks now and it does not work . Here are the details.... The Issue : ================== I am trying to Intiate a Call from PSTN phone to site B gateway (H323) 3033300 it should ask for authentication once authenticated press 1 to make any 4 digit calls if it is from SB phone 1 . Make sure to display 4 digits number for calling number along with calling name "SB Phone 1" they can use local gateway to make the call. Also 2nd line on PSTN phone should be used to dial 3033300 and you will prompted to login. Details: ============= My config is following.... 1) The dial-peers are set in the following way dial-peer voice 102 voip preference 2 destination-pattern 3300 session target ipv4:<ip address
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com