Thanks, removing the l3 bind, doing a shut, no shut on the serial interface then adding the l3 bind statement back in did it.
Thank you, much appreciated. On Jul 28, 2013, at 7:42, "ccie2k12" <ccie2...@gmail.com> wrote: > try removing > > ccm-manager config server 10.10.210.11 > ccm-manager config > > and remove > isdn bind-l3 ccm-manager > and put it back again. > > also > BR1 > pri-group timeslots 1-3,24 > PSTN > pri-group timeslots 1-3,23-24 > > should be same. > > > From: ccie_voice-boun...@onlinestudylist.com > [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Alex Pishko > Sent: Saturday, July 27, 2013 11:39 PM > To: ccie_voice@onlinestudylist.com > Subject: [OSL | CCIE_Voice] Lab 4A BR1 MGCP Issue > > All, > > Struggling with the MGCG PRI circuit in this lab. I've been through it a few > times and never had issues, however for this go around I cannot seem to get > L2 up when I issue the show isdn status command. Also, when I look at the > serial inteface is shows up/up, however it's up/up (spoofing). > > The MGCP portion appears to be workign correctly as when I issue a show > ccm-manager command I see it registered to the primary and within CUCM I see > the PRI as registered. Below is my relevant configuration from the BR1 > Router as well as the PSTN router. Also, on the PSTN I've tried to change > the pri-group to just 1-3,24 both had the same result. Also, when I issue > debug isdn q921 command I do not see any response for the SAMBE packet. Any > help on this would be much appreciated. I'm starting to think I may have a > hardware problem, but need a second or multiple sets of eyes on this before I > head down that router. > > Thank you all. > > Alex > > BR1 Router > > network-clock-participate wic 1 > network-clock-select 1 T1 0/1/0 > > controller T1 0/1/0 > framing esf > linecode b8zs > cablelength long 0db > pri-group timeslots 1-3,24 service mgcp > description **T1 Voice Connection to PSTN 0/1/1** > > interface Serial0/1/0:23 > no ip address > encapsulation hdlc > isdn switch-type primary-ni > isdn incoming-voice voice > isdn bind-l3 ccm-manager > no cdp enable > > voice-port 0/1/0:23 > ! > ccm-manager switchback immediate > ccm-manager redundant-host 10.10.210.10 > ccm-manager mgcp > ccm-manager music-on-hold > ccm-manager config server 10.10.210.11 > ccm-manager config > ! > mgcp > mgcp call-agent 10.10.210.11 2427 service-type mgcp version 0.1 > mgcp rtp unreachable timeout 1000 action notify > mgcp modem passthrough voip mode nse > mgcp package-capability rtp-package > mgcp package-capability sst-package > mgcp package-capability pre-package > no mgcp package-capability res-package > no mgcp timer receive-rtcp > mgcp sdp simple > mgcp rtp payload-type g726r16 static > mgcp bind control source-interface Loopback0 > mgcp bind media source-interface Loopback0 > > > PSTN Router > > network-clock-participate wic 1 > > controller T1 0/1/1 > framing esf > clock source internal > linecode b8zs > cablelength long 0db > pri-group timeslots 1-3,23-24 > description **T1 VOICE CONNECTION TO BR1-RTR 0/1/0** > > interface Serial0/1/1:23 > no ip address > encapsulation hdlc > isdn switch-type primary-ni > isdn protocol-emulate network > isdn incoming-voice voice > no cdp enable > > voice-port 0/1/1:23 > translation-profile incoming block-call-into-BR1 > translation-profile outgoing display-proper-ani-into-BR1 > >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
