There is only room for drives in the top half of the chassis.  The PSU and an assembly that holds the drives fills the top half. A 3.5" half-height drive fits in one side of the assembly and a 3.5" floppy drive fits in the other. The PSU cables go from the rear to the front of that side of the chassis, below the FDD (when the chassis is closed).

I did an exhibit on Sun lunchbox systems, including the IPC (4/40), for PNW VCF earlier this year. I looked for press kits, posters, etc. to use in the exhibit, but could only find text files. I know people who worked at Sun on the development of those early SPARCstations and none of them had any of that kind of material.

I had an audio cassette "Introducing the IPC" for Sun sales. I donated it to CHM this year (but I ripped the audio before I sent it to them).

alan

On 12/2/18 10:13 AM, ED SHARPE via cctalk wrote:
Thanks  for the  info  to  get it  open!  when  back at the  office   shall   
do that..   there  may  be  drives in 2 places -  on board and  the off board  
one. Always interesting to  explore  something   one  has  only  read  about!


Along the   same  line  of  UNIX   stuff   we  have a  COBALT   1U Pretty  blue  sever and a  COBALT  CUBE.  I  do remember   lusting  after  one of these   1U  COBALT  servers when they  were  current didn't  have anything in  the  budget  back then  though  for  one.  I  have  been  told  SUN  eventually ended up  owning COBALT. As  will all that   we    have  we  are  looking  for  any  ad slicks   press kits    posters,  wild artwork   for  the  Sun $/40,    and the  2  COBALT  machines.. Ed Sharpe archivist  for SMECC  www.smecc.org In a message dated 12/1/2018 8:15:39 PM US Mountain Standard Time, ape...@snowmoose.com writes:

Yes. It is next to floppy in the upper half of the chassis. There is a 50-pin (IDC connectors) ribbon cable that goes down to system board at the bottom of the lower half of the chassis. The chassis splits in the vertical middle in a, if looking at the chassis, fairly obvious place. Because of the cables that run from the top to bottom, it effectively hinges at the front of the chassis. There a couple buttons on the side to release and sometimes a security cable bit to remove (phillips screw).

On 12/1/18 7:08 PM, ED SHARPE wrote:
Hi  Alan - The  hard drive is same  size cabinet....    with  I  guess a  SCSSI 
  cable.  I  will have  to  look  at  it   further...   wonder if starting it  
out on  a  variac   would  help the capacitors  like  I  do  with the old radio 
sets  here in the museum  ed#


In a message dated 12/1/2018 8:04:03 PM US Mountain Standard Time,
ape...@snowmoose.com writes:
Well, as I said, in my experience, the NVRAMs that you can buy new from Mouser work good enough. And the mod to the original battery isn't that hard to make.

In my experience with IPCs, the bigger problem is the power supplies. If the PS 
on the IPC that you have now doesn't need to be re'capped now, it will need it 
soon. After that will likely be the HDD that needs work. Almost all of my HDDs 
that originally shipped with lunchbox systems up to the 424 meg (ST1480N) have 
died. The price for working 50-pin SCSI HDDs are at a point that SD2SCSI parts 
make more sense (unless you want to exhibit them as they originally ran).

alan

On 12/1/18 6:55 PM, ED SHARPE wrote:
BUMMER
It may become a static  display.....
Ed# In a message dated 12/1/2018 7:53:44 PM US Mountain Standard Time,
cctalk@classiccmp.org writes:
A 4/40 is a SPARCstation IPC. It used a M48T02 NVRAM for the IDPROM.

Yes, one with the dreaded battery.

alan

On 12/1/18 5:04 PM, Ed via cctalk wrote:
we were given this and a hard dribe a floor standimg decwriter..... does this 
use NV ram with dreaded battery? thanks,ed

Sent from AOL Mobile Mail

Reply via email to