Billy, Tell us these things.
What Operating System and Version are you using? Example Windows Vista, or Arch Linux, etc. Go to Device Manager if you're using Windows and see if there are any Warnings especially under connections and com ports. If so, what are the warnings? Unplug your cable into the computer from your radio. One of the com ports will go away in Device Manager. Now plug it in, you should get a notification, what com port does it say? Do you get a notification? Make sure the com port that you cable is using is the same one selected in CHIRP. Regards, David N1EA On Tue, May 14, 2019, 20:56 Billy Shirer <[email protected]> wrote: > I only have 3 Comm Ports > > On Tue, May 14, 2019, 8:46 PM Dan Jolley via chirp_users < > [email protected] wrote: > >> Billy, sometimes Windows changes them back from 3.2.0.0. Check your COM >> PORT and make sure it is on COM5. >> >> On Tuesday, May 14, 2019, 7:39:19 PM CDT, Billy Shirer < >> [email protected]> wrote: >> >> >> Okay, I will try that. >> Thanks >> >> On Tue, May 14, 2019, 7:44 PM Jardy via chirp_users < >> [email protected] wrote: >> >> Those cables can still be used if you roll the drivers back. Usually hits >> Prolific cables, use driver 3.2.0.0. No problems. >> >> Jardy Dawson WA7JRD >> Message sent through sub space hailing frequencies using the Universal >> Translator. >> >> >> On May 14, 2019, at 14:58, Steve Thomas <[email protected]> wrote: >> >> Is it a new cable? There are a lot of cables out there that have bad >> chips that used to work but don't work with newer versions of the Windows >> 10 driver. And since Windows 10 automatically updates the drivers, some >> cables that used to work quit along the way. >> On 5/14/2019 4:17 PM, Billy Shirer wrote: >> >> Yes, and again nothing happened >> >> On Tue, May 14, 2019, 5:12 PM Glenn At Home <[email protected] >> wrote: >> >> Did you try to download from your radio first? >> >> ----- Original Message ----- >> *From:* Billy Shirer <[email protected]> >> *To:* Discussion of CHIRP <[email protected]> >> *Sent:* Tuesday, May 14, 2019 4:03 PM >> *Subject:* Re: [chirp_users] Baofeng-uv82 >> >> I windows 10 >> >> I downloaded the Chirp Software and I connected my cable to my laptop and >> opened the download and proceeded to program my radio and the a window >> opened and said......No file found >> >> On Tue, May 14, 2019, 4:41 PM Glenn At Home <[email protected] >> wrote: >> >> What is your OS? >> What have you tried so far? >> >> ----- Original Message ----- >> *From:* Billy Shirer <[email protected]> >> *To:* [email protected] >> *Sent:* Tuesday, May 14, 2019 3:22 PM >> *Subject:* [chirp_users] Baofeng-uv82 >> >> I downloaded Chirp for my baofeng-uv82 and I can't get it Programmed >> >> ------------------------------ >> _______________________________________________ >> chirp_users mailing list >> [email protected] >> http://intrepid.danplanet.com/mailman/listinfo/chirp_users >> This message was sent to Glenn at [email protected] >> To unsubscribe, send an email to >> [email protected] >> _______________________________________________ >> chirp_users mailing list >> [email protected] >> http://intrepid.danplanet.com/mailman/listinfo/chirp_users >> This message was sent to Billy Shirer at [email protected] >> To unsubscribe, send an email to >> [email protected] >> >> ------------------------------ >> _______________________________________________ >> chirp_users mailing list >> [email protected] >> http://intrepid.danplanet.com/mailman/listinfo/chirp_users >> This message was sent to Glenn at [email protected] >> To unsubscribe, send an email to >> [email protected] >> _______________________________________________ >> chirp_users mailing list >> [email protected] >> http://intrepid.danplanet.com/mailman/listinfo/chirp_users >> This message was sent to Billy Shirer at [email protected] >> To unsubscribe, send an email to >> [email protected] >> >> >> _______________________________________________ >> chirp_users mailing >> [email protected]http://intrepid.danplanet.com/mailman/listinfo/chirp_users >> This message was sent to Steve Thomas at [email protected] >> To unsubscribe, send an email to >> [email protected] >> >> -- >> Steve Thomas, EMT-P >> Executive Director >> AlertCPR Emergency Training & Supply >> Office 866-569-7139 Cell [email protected] >> >> _______________________________________________ >> chirp_users mailing list >> [email protected] >> http://intrepid.danplanet.com/mailman/listinfo/chirp_users >> This message was sent to Jardy at [email protected] >> To unsubscribe, send an email to >> [email protected] >> >> _______________________________________________ >> chirp_users mailing list >> [email protected] >> http://intrepid.danplanet.com/mailman/listinfo/chirp_users >> This message was sent to Billy Shirer at [email protected] >> To unsubscribe, send an email to >> [email protected] >> >> _______________________________________________ >> chirp_users mailing list >> [email protected] >> http://intrepid.danplanet.com/mailman/listinfo/chirp_users >> This message was sent to Dan Jolley at [email protected] >> To unsubscribe, send an email to >> [email protected] >> _______________________________________________ >> chirp_users mailing list >> [email protected] >> http://intrepid.danplanet.com/mailman/listinfo/chirp_users >> This message was sent to Billy Shirer at [email protected] >> To unsubscribe, send an email to >> [email protected] > > _______________________________________________ > chirp_users mailing list > [email protected] > http://intrepid.danplanet.com/mailman/listinfo/chirp_users > This message was sent to D.J.J. Ring, Jr. at [email protected] > To unsubscribe, send an email to > [email protected]
_______________________________________________ chirp_users mailing list [email protected] http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to [email protected] at [email protected] To unsubscribe, send an email to [email protected]
