Yaesu FT270 H/H Greetings, so far I have used CHIRP with 100% success in programming many radios. What I REALLY need is being able to program the YAESU FT270 Hand Held. When is one of you brilliant guys going to update CHIRP with this radio?
Thanks VE7ECJ On Sun, Aug 22, 2021 at 12:01 PM <[email protected]> wrote: > Send chirp_users mailing list submissions to > [email protected] > > To subscribe or unsubscribe via the World Wide Web, visit > http://intrepid.danplanet.com/mailman/listinfo/chirp_users > or, via email, send a message with subject or body 'help' to > [email protected] > > You can reach the person managing the list at > [email protected] > > When replying, please edit your Subject line so it is more specific > than "Re: Contents of chirp_users digest..." > > > Today's Topics: > > 1. Re: UV5X Programming issue (White Ranger) > > > ---------------------------------------------------------------------- > > Message: 1 > Date: Sat, 21 Aug 2021 14:33:09 -0500 > From: White Ranger <[email protected]> > Subject: Re: [chirp_users] UV5X Programming issue > To: Discussion of CHIRP <[email protected]> > Message-ID: > <CAP+N95FGwe= > [email protected]> > Content-Type: text/plain; charset="utf-8" > > Radio should be ON when up or downloading. > Remove the driver and cable program, reboot PC reload driver > SHOULD correct issue. If using aftermarket cable check to see contacts are > CLEAN (*shiny) and fit TIGHTLY into the mike provisioning adapter (Mic > jack) DO NOT touch ANY buttons while programming. Worst case, prior to > programming RESET the radio to factory resets then load your amended > program. > > On Thu, Aug 19, 2021 at 2:03 PM Jim Unroe <[email protected]> wrote: > > > Hi Eric, > > > > On Thu, Aug 19, 2021 at 12:47 PM Eric Chopin <[email protected]> > wrote: > > > > > > UV5XP.... > > > However to get CHIRP to see the radio either in the 'Download from > > radio' > > > or 'Upload to radio' ... with the cable plugged in to my PC or my > > MAC, the > > > radio must me switched OFF...then as I select 'Download or upload' > > as I > > > select 'OK' i must immediately switch ON my radio then CHIRP sees > it > > and > > > proceeds. If I try to 'Download or upload' with the radio already > > switched > > > on I get the message 'The radio did not respond' as CHIRP cannot > see > > it > > > connected. > > > Any suggestions? > > > Thanks > > > VE7ECJ > > > > That sounds like a programming cable/driver issue. Also, to program > > that radio you must choose... > > > > Vendor: Radioddity > > Model: UV-5G > > > > Jim KC9HI > > _______________________________________________ > > chirp_users mailing list > > [email protected] > > http://intrepid.danplanet.com/mailman/listinfo/chirp_users > > This message was sent to [email protected] at > > [email protected] > > To unsubscribe, send an email to > > [email protected] > > > -------------- next part -------------- > An HTML attachment was scrubbed... > URL: > http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20210821/b544e8b4/attachment-0001.html > > ------------------------------ > > _______________________________________________ > chirp_users mailing list > [email protected] > http://intrepid.danplanet.com/mailman/listinfo/chirp_users > To unsubscribe, send an email to > [email protected] > > End of chirp_users Digest, Vol 152, Issue 12 > ******************************************** >
_______________________________________________ chirp_users mailing list [email protected] http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to [email protected] at [email protected] To unsubscribe, send an email to [email protected]
