Interesting. Why does it work?
-- Regards, Jason Plank CCIE #16560 e: [EMAIL PROTECTED] -------------- Original message ---------------------- From: "Fred Reimer" <[EMAIL PROTECTED]>
--- Begin Message ---Your configuration is wrong then. The DHCP option should point to the management interface. The AP should do a LWAPP Discover and the management interface should return a list of IP addresses that the AP can connect to (ap-manager address(es)), along with the relative load on each interface (max AP's and total AP's). See section 5.2.4 and 5.2.5 of the draft: 5.2.4. WTP Manager Control IPv4 Address The WTP Manager Control IPv4 Address message element is sent by the AC to the WTP during the discovery process and is used by the AC to provide the interfaces available on the AC, and their current load. This message element is useful for the WTP to perform load balancing across multiple interfaces. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | IP Address | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | WTP Count | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Type: 99 for WTP Manager Control IPv4 Address Length: 6 5.2.5. WTP Manager Control IPv6 Address The WTP Manager Control IPv6 Address message element is sent by the AC to the WTP during the discovery process and is used by the AC to provide the interfaces available on the AC, and their current load. This message element is useful for the WTP to perform load balancing across multiple interfaces. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | IP Address | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | IP Address | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | IP Address | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | IP Address | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | WTP Count | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Type: 137 for WTP Manager Control IPv6 Address Length: 6 IP Address: The IP Address of an interface. WTP Count: The number of WTPs currently connected to the interface. Fred Reimer, CISSP, CCNP, CQS-VPN, CQS-ISS Senior Network Engineer Coleman Technologies, Inc. 954-298-1697 > -----Original Message----- > From: [EMAIL PROTECTED] [mailto:cisco-nsp- > [EMAIL PROTECTED] On Behalf Of [EMAIL PROTECTED] > Sent: Thursday, May 22, 2008 9:28 AM > To: Rupert Finnigan; cisco-nsp@puck.nether.net > Subject: Re: [c-nsp] LWAPP Problems > > I have always used the ap-manager interface in my DHCP option 43 > configuration. My understanding is that the Management interface is > used for controller to controller traffic to terminate EOIP tunnels. I > would call your configuration correct now :) > > -- > Regards, > > Jason Plank > CCIE #16560 > e: [EMAIL PROTECTED] > > -------------- Original message ---------------------- > From: "Rupert Finnigan" <[EMAIL PROTECTED]> > > Hi, > > > > Thanks to all who offered advise - It was the IP address in the end. > I'd > > setup DHCP Option 43 to the ap-manager interface address, and not the > > management one. Now that's corrected all is fine. I'm still confused > as to > > how this particular network has worked in the past though! > > > > Thanks again, > > > > Rupert > > _______________________________________________ > > cisco-nsp mailing list cisco-nsp@puck.nether.net > > https://puck.nether.net/mailman/listinfo/cisco-nsp > > archive at http://puck.nether.net/pipermail/cisco-nsp/ > > _______________________________________________ > cisco-nsp mailing list cisco-nsp@puck.nether.net > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/smime.p7s
Description: S/MIME cryptographic signature
--- End Message ---
_______________________________________________ cisco-nsp mailing list cisco-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/