On A0.1..... config-subif)#service-policy output Voice CBWFQ : Not supported on subinterfaces
On A0 (config-if)#service-policy output Voice CBWFQ : Not supported on this interface It would seem out old ways of QoS have changed ;) On Tue, Jul 7, 2009 at 4:06 PM, Siva Valliappan <svall...@cisco.com> wrote: > IIRC you need to apply it on the ATM interface > e.g. > > Interface ATM0.1 point-to-point > . > . > pvc 1/100 > service-policy output Voice > > regards > .siva > > > > On Tue, 7 Jul 2009, Clue Store wrote: > > Hi All, >> >> >> I am having a hard time trying to figure how to apply a QoS policy on this >> router. I have applied a few typical service-policies on the dialer >> interfaces, but a "show policy interface di0" shows packets being matched >> but nothing being dropped and the link is saturated. I believe the policy >> needs to be applied to the virtual-access interface that comes up when PPP >> negotiates, but i'm not quite sure how this would be done since the use of >> vpdn-groups are no longer used. Relevent config posted. Any suggestions >> are >> greatly appreciated. *And yes I know the service-policy is not applied to >> the dialer interface...this was due to it not working. >> >> >> class-map match-any VoIP >> match ip rtp 16384 16383 >> match access-group name VoicePorts >> ! >> ! >> policy-map Voice >> class VoIP >> priority 256 >> ! >> ! >> ! >> ! >> ! >> interface Ethernet0 >> ip address 192.168.10.1 255.255.255.0 >> ip nat inside >> ip virtual-reassembly >> ! >> interface Ethernet2 >> no ip address >> shutdown >> hold-queue 100 out >> ! >> interface ATM0 >> no ip address >> load-interval 30 >> no atm ilmi-keepalive >> dsl operating-mode auto >> ! >> interface ATM0.1 point-to-point >> pvc 1/100 >> encapsulation aal5snap >> pppoe-client dial-pool-number 1 >> ! >> ! >> interface FastEthernet1 >> duplex auto >> speed auto >> ! >> interface FastEthernet2 >> duplex auto >> speed auto >> ! >> interface FastEthernet3 >> duplex auto >> speed auto >> ! >> interface FastEthernet4 >> duplex auto >> speed auto >> ! >> ! >> interface Dialer0 >> ip address negotiated >> ip mtu 1492 >> ip nat outside >> ip virtual-reassembly >> encapsulation ppp >> ip tcp adjust-mss 1412 >> dialer pool 1 >> no cdp enable >> <ppp info ************> >> ! >> ip forward-protocol nd >> ip route 0.0.0.0 0.0.0.0 Dialer0 >> ! >> ip http server >> no ip http secure-server >> ! >> no ip nat service skinny tcp port 2000 >> no ip nat service sip udp port 5060 >> ip nat inside source list 10 interface Dialer0 overload >> ! >> ! >> ip access-list extended VoicePorts >> permit udp any host *.*.*.* range 22026 62025 >> permit udp any host *.*.*.* range 22026 62025 >> access-list 10 permit 192.168.10.0 0.0.0.255 >> _______________________________________________ >> cisco-nsp mailing list cisco-nsp@puck.nether.net >> https://puck.nether.net/mailman/listinfo/cisco-nsp >> archive at http://puck.nether.net/pipermail/cisco-nsp/ >> >> _______________________________________________ cisco-nsp mailing list cisco-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/