it's been many years since i worked in this area, so you will need to
bear with me.
couple of things to check. can you do a "show log" and is there any
other messages that were generated when you tried to configure the
service policy on the ATM interface?
do you have a "vbr-nrt <bw>" definition under the ATM interface?
can you configure that first, and then configure the service policy
statement? does it resolve the issue? if not, what were the log messages
that were generated?
thanks
.siva
On Tue, 7 Jul 2009, Clue Store wrote:
On A0.1.....
config-subif)#service-policy output Voice
CBWFQ : Not supported on subinterfaces
On A0
(config-if)#service-policy output Voice
CBWFQ : Not supported on this interface
It would seem out old ways of QoS have changed ;)
On Tue, Jul 7, 2009 at 4:06 PM, Siva Valliappan <svall...@cisco.com> wrote:
IIRC you need to apply it on the ATM interface
e.g.
Interface ATM0.1 point-to-point
.
.
pvc 1/100
service-policy output Voice
regards
.siva
On Tue, 7 Jul 2009, Clue Store wrote:
Hi All,
I am having a hard time trying to figure how to apply a QoS policy on this
router. I have applied a few typical service-policies on the dialer
interfaces, but a "show policy interface di0" shows packets being matched
but nothing being dropped and the link is saturated. I believe the policy
needs to be applied to the virtual-access interface that comes up when PPP
negotiates, but i'm not quite sure how this would be done since the use of
vpdn-groups are no longer used. Relevent config posted. Any suggestions
are
greatly appreciated. *And yes I know the service-policy is not applied to
the dialer interface...this was due to it not working.
class-map match-any VoIP
match ip rtp 16384 16383
match access-group name VoicePorts
!
!
policy-map Voice
class VoIP
priority 256
!
!
!
!
!
interface Ethernet0
ip address 192.168.10.1 255.255.255.0
ip nat inside
ip virtual-reassembly
!
interface Ethernet2
no ip address
shutdown
hold-queue 100 out
!
interface ATM0
no ip address
load-interval 30
no atm ilmi-keepalive
dsl operating-mode auto
!
interface ATM0.1 point-to-point
pvc 1/100
encapsulation aal5snap
pppoe-client dial-pool-number 1
!
!
interface FastEthernet1
duplex auto
speed auto
!
interface FastEthernet2
duplex auto
speed auto
!
interface FastEthernet3
duplex auto
speed auto
!
interface FastEthernet4
duplex auto
speed auto
!
!
interface Dialer0
ip address negotiated
ip mtu 1492
ip nat outside
ip virtual-reassembly
encapsulation ppp
ip tcp adjust-mss 1412
dialer pool 1
no cdp enable
<ppp info ************>
!
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer0
!
ip http server
no ip http secure-server
!
no ip nat service skinny tcp port 2000
no ip nat service sip udp port 5060
ip nat inside source list 10 interface Dialer0 overload
!
!
ip access-list extended VoicePorts
permit udp any host *.*.*.* range 22026 62025
permit udp any host *.*.*.* range 22026 62025
access-list 10 permit 192.168.10.0 0.0.0.255
_______________________________________________
cisco-nsp mailing list cisco-nsp@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
_______________________________________________
cisco-nsp mailing list cisco-nsp@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
