On 1/31/13 4:10 PM, false wrote: > Here is the output from "debug ppp negotiation". I'd say no one is responding > on the other end.(??) Thoughts?
Agreed. If you are in control of the other end, take a look there. If you aren't, open a trouble ticket with them. You need to troubleshoot this problem in conjunction with the other end of the circuit. > Jan 31 14:12:52.181 CST: %LINK-3-UPDOWN: Interface Serial0/1/0, changed state > to > up > 000401: Jan 31 14:12:52.181 CST: Se0/1/0 PPP: Using default call direction > 000402: Jan 31 14:12:52.185 CST: Se0/1/0 PPP: Treating connection as a > dedicated > line > 000403: Jan 31 14:12:52.185 CST: Se0/1/0 PPP: Session handle[4F00000E] > Session i > d[9] > 000404: Jan 31 14:12:52.185 CST: Se0/1/0 PPP: Phase is ESTABLISHING, Active > Open > > 000405: Jan 31 14:12:52.185 CST: Se0/1/0 LCP: O CONFREQ [Closed] id 8 len 10 > 000406: Jan 31 14:12:52.185 CST: Se0/1/0 LCP: MagicNumber 0x60279E3E > (0x05066 > 0279E3E) > 000407: Jan 31 14:12:54.180 CST: Se0/1/0 LCP: Timeout: State REQsent > 000408: Jan 31 14:12:54.180 CST: Se0/1/0 LCP: O CONFREQ [REQsent] id 9 len 10 > 000409: Jan 31 14:12:54.180 CST: Se0/1/0 LCP: MagicNumber 0x60279E3E > (0x05066 > 0279E3E) > 000410: Jan 31 14:12:56.196 CST: Se0/1/0 LCP: Timeout: State REQsent > 000411: Jan 31 14:12:56.196 CST: Se0/1/0 LCP: O CONFREQ [REQsent] id 10 len 10 > 000412: Jan 31 14:12:56.196 CST: Se0/1/0 LCP: MagicNumber 0x60279E3E > (0x05066 > 0279E3E) > 000413: Jan 31 14:12:58.212 CST: Se0/1/0 LCP: Timeout: State REQsent > 000414: Jan 31 14:12:58.212 CST: Se0/1/0 LCP: O CONFREQ [REQsent] id 11 len 10 > 000415: Jan 31 14:12:58.212 CST: Se0/1/0 LCP: MagicNumber 0x60279E3E > (0x05066 > 0279E3E) > 000416: Jan 31 14:13:00.228 CST: Se0/1/0 LCP: Timeout: State REQsent > 000417: Jan 31 14:13:00.228 CST: Se0/1/0 LCP: O CONFREQ [REQsent] id 12 len 10 > 000418: Jan 31 14:13:00.228 CST: Se0/1/0 LCP: MagicNumber 0x60279E3E > (0x05066 > 0279E3E) > 000419: Jan 31 14:13:02.243 CST: Se0/1/0 LCP: Timeout: State REQsent > 000420: Jan 31 14:13:02.243 CST: Se0/1/0 LCP: O CONFREQ [REQsent] id 13 len 10 > 000421: Jan 31 14:13:02.243 CST: Se0/1/0 LCP: MagicNumber 0x60279E3E > (0x05066 > 0279E3E) > 000422: Jan 31 14:13:04.259 CST: Se0/1/0 LCP: Timeout: State REQsent > 000423: Jan 31 14:13:04.259 CST: Se0/1/0 LCP: O CONFREQ [REQsent] id 14 len 10 > 000424: Jan 31 14:13:04.259 CST: Se0/1/0 LCP: MagicNumber 0x60279E3E > (0x05066 > 0279E3E) > 000425: Jan 31 14:13:06.275 CST: Se0/1/0 LCP: Timeout: State REQsent > 000426: Jan 31 14:13:06.275 CST: Se0/1/0 LCP: O CONFREQ [REQsent] id 15 len 10 > 000427: Jan 31 14:13:06.275 CST: Se0/1/0 LCP: MagicNumber 0x60279E3E > (0x05066 > 0279E3E) > 000428: Jan 31 14:13:08.291 CST: Se0/1/0 LCP: Timeout: State REQsent > 000429: Jan 31 14:13:08.291 CST: Se0/1/0 LCP: O CONFREQ [REQsent] id 16 len 10 > 000430: Jan 31 14:13:08.291 CST: Se0/1/0 LCP: MagicNumber 0x60279E3E > (0x05066 > 0279E3E) > 000431: Jan 31 14:13:09.535 CST: %SYS-5-CONFIG_I: Configured from console by > adm > in on vty0 (192.168.2.138) > 000432: Jan 31 14:13:10.307 CST: Se0/1/0 LCP: Timeout: State REQsent > 000433: Jan 31 14:13:10.307 CST: Se0/1/0 LCP: O CONFREQ [REQsent] id 17 len 10 > 000434: Jan 31 14:13:10.307 CST: Se0/1/0 LCP: MagicNumber 0x60279E3E > (0x05066 > 0279E3E) > > --- On Thu, 1/31/13, Jay Hennigan <j...@west.net> wrote: > >> From: Jay Hennigan <j...@west.net> >> Subject: Re: [c-nsp] Cisco s0/1/0 T-1 is up but not showing up in route table >> To: cisco-nsp@puck.nether.net >> Date: Thursday, January 31, 2013, 11:45 AM >> On 1/31/13 8:57 AM, false wrote: >>> I cannot ping the far end. The int s0/1/0 output shows >> up/up. The "sh service-module serial 0/1/0" output listed >> below shows the T1 is up with the correct framing, >> etc. The "sh diag" output below looks to be clean. >> Here is the output for "sh int s0/1/0" as well. I am totally >> at a loss here. Any ideas? Thank you >>> >>> sh int s0/1/0 >>> Serial0/1/0 is up, line protocol is up >>> Hardware is GT96K with integrated T1 >> CSU/DSU >>> Internet address is x.x.x.x/30 >>> MTU 1500 bytes, BW 1536 Kbit/sec, DLY >> 20000 usec, >>> reliability 255/255, txload 1/255, >> rxload 1/255 >>> Encapsulation PPP, LCP Open >>> Listen: IPCP, CDPCP, loopback not set >> ^^^^^^^^^^^^^ >> >> This should be Open: IPCP >> >> What does the other end look like? Is its IP >> configured correctly, >> static address of the other side of the /30 ? >> >> What do you see with "debug ppp negotiation"? This >> should give you a >> hint as to where the problem lies. >> >> -- >> Jay Hennigan - CCIE #7880 - Network Engineering - j...@impulse.net >> Impulse Internet Service - http://www.impulse.net/ >> Your local telephone and internet company - 805 884-6323 - >> WB6RDV >> _______________________________________________ >> cisco-nsp mailing list cisco-nsp@puck.nether.net >> https://puck.nether.net/mailman/listinfo/cisco-nsp >> archive at http://puck.nether.net/pipermail/cisco-nsp/ >> -- -- Jay Hennigan - CCIE #7880 - Network Engineering - j...@impulse.net Impulse Internet Service - http://www.impulse.net/ Your local telephone and internet company - 805 884-6323 - WB6RDV _______________________________________________ cisco-nsp mailing list cisco-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
