Network Side PRI SIgnalling first was introduced in 12.1(2)XH version of
IOS,
RGRDS,
Evgeny
"Chris Larson" <[EMAIL PROTECTED]> wrote in message
009AE8FD8584D3119A2E0008C7F4A84929D2@WEBSERVER">news:009AE8FD8584D3119A2E0008C7F4A84929D2@WEBSERVER...
> I had heard rumors about this, but have never heard of anyone doing it.
>
> I tried this on my 3640 running 12.0(7) and there is no ISDN network
> command. Maybe you need enterprise IOS (I am running IP Plus IPSEC). There
> is a way to set TEI statically, but I do not think that would be
sufficient.
> I did not follow through with a complete config.
>
> -----Original Message-----
> From: K Sacca [mailto:[EMAIL PROTECTED]]
> Sent: Friday, June 30, 2000 4:54 PM
> To: Daniel Cotts; '[EMAIL PROTECTED]'; '[EMAIL PROTECTED]'
> Subject: RE: Need help
>
>
> Try the following and see if it works. I was provided
> this information by a colleague.
>
> Are you trying to set up a back-to-back connection
> using ISDN ? If
> that's the case, on the peer serial0:23 interace, you
> need to issue the
> command ISDN network. This simulates the network
> (switch) side of the
> ISDN connection.
>
> You can verify that by doing 'show isdn status' and it
> should say
> '**network side configuration'. Be careful with clock
> sources tho.
> Generally I make the side which is acting as the
> network use the
> internal clock. This can be done by doing 'clock
> source internal' on the
> t1 controller
>
> Regards Kamoto
>
>
> --- Daniel Cotts <[EMAIL PROTECTED]> wrote:
> > First you need two routers with an ISDN BRI
> > interface. Note some have a U
> > interface for USA connections while others have an
> > S/T interface that is
> > used in the rest of the world. Note that a NT-1
> > adapter converts the S/T on
> > the router to interact with the U provided by the
> > Telco.
> > To connect them you must either have the Telco
> > provide ISDN service or
> > purchase an ISDN simulator. Two manufacturers of
> > simulators are:
> > 1) Arca Technologies - call Dean Coleman
> > 800-888-1978 ext 252 also
> > www.arca.com Lotsa toys!
> > 2)Teltone check out www.teltone.com or talk to
> > communications distributors
> > such as Graybar or Anixter, etc. Also Specialized
> > Products 800-866-5353.
> > Good service but most likely not the lowest price.
> > Simulators are expensive.
> >
> > > -----Original Message-----
> > > From: [EMAIL PROTECTED]
> > [mailto:[EMAIL PROTECTED]]
> > > Sent: Thursday, June 29, 2000 8:23 PM
> > > To: [EMAIL PROTECTED]
> > > Subject: Need help
> > >
> > >
> > > Any Ideas on how can I configure a lab network to
> > simulate
> > > ISDN can a cisco
> > > router do this job if yes which router.
> > >
> > > Regards,
> > > Amir
> > >
> > > ___________________________________
> > > UPDATED Posting Guidelines:
> > http://www.groupstudy.com/list/guide.html
> > > FAQ, list archives, and subscription info:
> > http://www.groupstudy.com
> > > Report misconduct and Nondisclosure violations to
> > [EMAIL PROTECTED]
> > >
> >
> > ___________________________________
> > UPDATED Posting Guidelines:
> > http://www.groupstudy.com/list/guide.html
> > FAQ, list archives, and subscription info:
> > http://www.groupstudy.com
> > Report misconduct and Nondisclosure violations to
> [EMAIL PROTECTED]
>
>
> __________________________________________________
> Do You Yahoo!?
> Get Yahoo! Mail - Free email you can access from anywhere!
> http://mail.yahoo.com/
>
> ___________________________________
> UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
> FAQ, list archives, and subscription info: http://www.groupstudy.com
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
>
> ___________________________________
> UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
> FAQ, list archives, and subscription info: http://www.groupstudy.com
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
> ---
___________________________________
UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
FAQ, list archives, and subscription info: http://www.groupstudy.com
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
