Catherine, You forget to define ospf network type in each frame interface. Add this interface config command: ip ospf network point-to-point
Thank, Rivalino On Mon, 2 Jun 2003, Catherine Wu wrote: > I am testing Hub-Spoke for OSPF over FR, > > I verified the neighbor adjacency,but I couldn't see route 2.2.2.2 and > 3.3.3.3 in the routing table, > > RouterA#sh ip ospf nei > > Neighbor ID Pri State Dead Time Address Interface > 3.3.3.3 1 FULL/ - 00:01:41 10.1.1.6 > Serial0/0.2 > 2.2.2.2 1 FULL/ - 00:01:39 10.1.1.2 > Serial0/0.1 > RouterB#sh ip ospf nei > > Neighbor ID Pri State Dead Time Address Interface > 1.1.1.1 1 FULL/BDR 00:01:38 10.1.1.1 Serial0/0 > RouterC#sh ip ospf nei > > Neighbor ID Pri State Dead Time Address Interface > 1.1.1.1 1 FULL/BDR 00:01:34 10.1.1.5 Serial0/0 > > RouterA#sh ip ro > Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP > D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area > N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 > E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP > i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter > area > * - candidate default, U - per-user static route, o - ODR > P - periodic downloaded static route > > Gateway of last resort is not set > > 1.0.0.0/32 is subnetted, 1 subnets > C 1.1.1.1 is directly connected, Loopback0 > 10.0.0.0/30 is subnetted, 2 subnets > C 10.1.1.0 is directly connected, Serial0/0.1 > C 10.1.1.4 is directly connected, Serial0/0.2 > > Please help. > > Thanks > > Catherine > ---------------------------------------------------- > RouterA > interface Loopback0 > ip address 1.1.1.1 255.255.255.255 > ! > interface Serial0/0 > no ip address > encapsulation frame-relay > frame-relay lmi-type ansi > no sh > ! > interface Serial0/0.1 point-to-point > ip address 10.1.1.1 255.255.255.252 > ip ospf hello-interval 30 > frame-relay interface-dlci 101 > ! > interface Serial0/0.2 point-to-point > ip address 10.1.1.5 255.255.255.252 > ip ospf hello-interval 30 > frame-relay interface-dlci 102 > ! > router ospf 1 > log-adjacency-changes > network 1.1.1.1 0.0.0.0 area 1 > network 10.1.1.0 0.0.0.3 area 0 > network 10.1.1.4 0.0.0.3 area 0 > > RouterB > ! > interface Loopback0 > ip address 2.2.2.2 255.255.255.255 > ! > interface Serial0/0 > ip address 10.1.1.2 255.255.255.252 > encapsulation frame-relay > frame-relay map ip 10.1.1.1 110 broadcast > no frame-relay inverse-arp > frame-relay lmi-type ansi > no sh > ! > router ospf 1 > log-adjacency-changes > network 2.2.2.2 0.0.0.0 area 2 > network 10.1.1.0 0.0.0.3 area 0 > neighbor 10.1.1.1 > ! > RouterC > interface Loopback0 > ip address 3.3.3.3 255.255.255.255 > ! > interface Serial0/0 > ip address 10.1.1.6 255.255.255.252 > encapsulation frame-relay > frame-relay map ip 10.1.1.5 120 broadcast > no frame-relay inverse-arp > frame-relay lmi-type ansi > no sh > ! > router ospf 1 > log-adjacency-changes > network 3.3.3.3 0.0.0.0 area 3 > network 10.1.1.4 0.0.0.3 area 0 > neighbor 10.1.1.5 > > [GroupStudy removed an attachment of type application/ms-tnef which had a > name of winmail.dat] Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=70036&t=70025 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]