Thanks for everyones assistance. It turned out that this was a known issue on this release but it was undocumented. We upgraded and all is well.
Thanks, Mario Puras SoluNet Technical Support Mailto: [EMAIL PROTECTED] Direct: (321) 309-1410 888.449.5766 (USA) / 888.SOLUNET (Canada) -----Original Message----- From: Walker, James, IS [mailto:[EMAIL PROTECTED] Sent: Tuesday, June 10, 2003 1:35 PM To: '[EMAIL PROTECTED]'; [EMAIL PROTECTED] Subject: RE: No output on "show run" [7:70461] Hi, Can you post the out of 'sh proc mem'? Thanks, _________________________________________ Jim Walker Network Engineer (617) 732-8803 -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Sent: Tuesday, June 10, 2003 11:29 AM To: [EMAIL PROTECTED] Subject: No output on "show run" [7:70461] Hi all, I have an issue on a 7200 where it appears that I am running out of memory although none of the show outputs that I have seen tell me that. When I try to issue the "show run" nothing happens, I get no output. If I try to copy start run it gives me the following error: Router#sh run Router#copy start run Destination filename [running-config]? %Error opening system:/running-config (Not enough space) Router# I was thinking that perhaps this configuration is to large and it needs to be compressed. Perhaps I need to use the command "service compress-config" but not quite sure since all this is doing is compressing the NVRAM portion. I dont think that that is where my problem is but I could be wrong, please explain. Could someone explain to me what causes this to occur and how to fix it (besides a reboot). Here is the output of the "show version". Router#sh ver Cisco Internetwork Operating System Software IOS (tm) 7200 Software (C7200-IO3S-M), Version 12.2(2)T, RELEASE SOFTWARE (fc1) TAC Support: http://www.cisco.com/cgi-bin/ibld/view.pl?i=support Copyright (c) 1986-2001 by cisco Systems, Inc. Compiled Sun 03-Jun-01 04:30 by ccai Image text-base: 0x600089C0, data-base: 0x6149E000 ROM: System Bootstrap, Version 12.0(19990210:195103) [12.0XE 105], DEVELOPMENT SOFTWARE BOOTFLASH: 7200 Software (C7200-BOOT-M), Version 12.0(10)S, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) Router uptime is 18 hours, 30 minutes System returned to ROM by power-on System restarted at 15:09:19 cdt Mon Jun 9 2003 System image file is "slot0:c7200-io3s-mz.122-2.T.bin" cisco 7206VXR (NPE300) processor (revision D) with 122880K/40960K bytes of memory. Processor board ID 20394201 R7000 CPU at 262Mhz, Implementation 39, Rev 2.1, 256KB L2, 2048KB L3 Cache 6 slot VXR midplane, Version 2.0 Last reset from power-on Bridging software. X.25 software, Version 3.0.0. 2 FastEthernet/IEEE 802.3 interface(s) 10 ATM network interface(s) 125K bytes of non-volatile configuration memory. 20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K). 4096K bytes of Flash internal SIMM (Sector size 256K). Configuration register is 0x102 Router#sh run Router#copy start run Destination filename [running-config]? %Error opening system:/running-config (Not enough space) Router# Thanks, Mario Puras SoluNet Technical Support Mailto: [EMAIL PROTECTED] Direct: (321) 309-1410 888.449.5766 (USA) / 888.SOLUNET (Canada) Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=70467&t=70461 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
