What do you see in your log? How about a sh mem? If it is a memory problem it is not the lack of flash that would cause this. If your not on the console trying doing as a "term mon" and reissue the sh runn and see if your getting errors.
Dave [EMAIL PROTECTED] wrote: > Hi all, > > I have an issue on a 7200 where it appears that I am running out of memory > although none of the show outputs that I have seen tell me that. When I try > to issue the "show run" nothing happens, I get no output. If I try to copy > start run it gives me the following error: > > > Router#sh run > Router#copy start run > Destination filename [running-config]? > %Error opening system:/running-config (Not enough space) > Router# > > > I was thinking that perhaps this configuration is to large and it needs to > be compressed. Perhaps I need to use the command "service compress-config" > but not quite sure since all this is doing is compressing the NVRAM portion. > I dont think that that is where my problem is but I could be wrong, please > explain. > > Could someone explain to me what causes this to occur and how to fix it > (besides a reboot). > > Here is the output of the "show version". > > > > Router#sh ver > Cisco Internetwork Operating System Software > IOS (tm) 7200 Software (C7200-IO3S-M), Version 12.2(2)T, RELEASE SOFTWARE > (fc1) > TAC Support: http://www.cisco.com/cgi-bin/ibld/view.pl?i=support > Copyright (c) 1986-2001 by cisco Systems, Inc. > Compiled Sun 03-Jun-01 04:30 by ccai > Image text-base: 0x600089C0, data-base: 0x6149E000 > > ROM: System Bootstrap, Version 12.0(19990210:195103) [12.0XE 105], > DEVELOPMENT SOFTWARE > BOOTFLASH: 7200 Software (C7200-BOOT-M), Version 12.0(10)S, EARLY DEPLOYMENT > RELEASE SOFTWARE (fc1) > > Router uptime is 18 hours, 30 minutes > System returned to ROM by power-on > System restarted at 15:09:19 cdt Mon Jun 9 2003 > System image file is "slot0:c7200-io3s-mz.122-2.T.bin" > > cisco 7206VXR (NPE300) processor (revision D) with 122880K/40960K bytes of > memory. > Processor board ID 20394201 > R7000 CPU at 262Mhz, Implementation 39, Rev 2.1, 256KB L2, 2048KB L3 Cache > 6 slot VXR midplane, Version 2.0 > > Last reset from power-on > Bridging software. > X.25 software, Version 3.0.0. > 2 FastEthernet/IEEE 802.3 interface(s) > 10 ATM network interface(s) > 125K bytes of non-volatile configuration memory. > > 20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K). > 4096K bytes of Flash internal SIMM (Sector size 256K). > Configuration register is 0x102 > > Router#sh run > Router#copy start run > Destination filename [running-config]? > %Error opening system:/running-config (Not enough space) > Router# > > > Thanks, > > Mario Puras > SoluNet Technical Support > Mailto: [EMAIL PROTECTED] > Direct: (321) 309-1410 > 888.449.5766 (USA) / 888.SOLUNET (Canada) -- David Madland CCIE# 2016 Sr. Network Engineer Qwest Communications 612-664-3367 "Government can do something for the people only in proportion as it can do something to the people." -- Thomas Jefferson Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=70472&t=70461 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
